Ken A Vision PrepScope T-1252 Bedienungsanleitung

5615 Raytown Road, Kansas City, MO 64133 U.S.A Tel. 816-353-4787 Fax. 816-358-5072

Email: [email protected] www.ken-a-vision.com

11.03

Direct X 8.1

CARE AND MAINTENANCE

Your Digital Prep Scope is a fine precision instrument and should be treated

with care. When not in use it should be protected from dust by the plastic cover

provided. Lenses and eyepieces should be cleaned periodically with optical lens

tissue which is soft and lint free. Painted surfaces can be cleaned with a moistened

cloth.

Ken-A-Vision has qualified technicians on staff to repair and service all your

microscopes. Contact us at 1.816.353.4787 for more details.

Ken-A-Vision reserves the right to make design improvements and other changes in accordance with

the latest technology. There is no obligation to make changes in products already manufactured. Copy

Right 2003 Ken-A-Vision Corporation.

WARRANTY: ONE YEAR (CAMERA) AND TEN YEAR (MICROSCOPE WARRANTY AGAINST

DEFECTIVE PARTS AND WORKMANSHIP.

Digital Prep Scope

Instruction Manual

T-1252

INS-SC50DVP

Connecting The USB Cable:

The USB cable is pre-attached to your Digital Prep Scope. Please note that

you must first install the supplied software before connecting the USB cable to

your computer. For the initial setup to be complete, before connecting the USB

cable to your computer be sure the software CD supplied is still in your CD Rom

Focus

With the Digital Prep Scope connected to the USB port, the switch turned on,

place a prepared slide under the stage clips and move into position for viewing.

Use the 4x objective first. Raise the stage until it will go no higher. Then lower the

stage to bring into focus. (View the image on the computer screen or through the

eyepiece) Once the image is sharp you should be able to simply turn the nose-

piece to the next higher objective lens and do minor adjustments with the fine

focus knob.

Diopter

After obtaining focus of the specimen on monitor/computer using the micro-

scope focus adjustments, adjust the diopter, located on eyepiece tube, for individ-

ual eye correction when viewing through the microscope.

Disk Diaphragm

The rotating disk is located under the stage. (2 = smallest, and 8 = largest)

The different sized holes are used to control the amount of light that is projected

upward into the slide. Simply bring one of the different sized holes in line with

the stage opening. These is no set rule regarding which setting to use with a

particular lens.

Built-In Illuminator

The light source life is approximately 100,000 hours and can be turned on

and off with the power switch located on the side of the unit. The light source is

Eyepiece

The widefield eyepiece is locked into place to avoid loss. Their should be no

need to tighten. An eyepointer is built-in to the eyepiece. The diopter on the

eyepiece tube allows for focus adjustment while viewing specimens.

System Recommendations:

Pentium II 433mhz

Microsoft Internet Explorer 5.0

128mb of RAM

Windows 98 (SE), 2000, ME, XP

8mb Video (24bit color)

Digital Prep Scope

APPLICATION

Thank you for purchasing your Ken-A-Vision Digital Prep Scope. We designed

this compact digital microscope with optical quality and to withstand student use.

The contoured metal base is covered with high-density plastic to prevent chipping

during normal student use. These and other features, were designed to enhance

the Digital Prep Scope to offer you the best value.

TECHNICAL SPECIFICATIONS

* 10x Widefield eyepiece with pointer

* DIN Objective lens: 4x, 10x, 40xR

* Coarse & Fine Focal Adjustmnet

* Power Source: USB

* Light Source: “Propietary Light Board” Technology Equivalent to a 20 watt

bulb

* “Light Board” Life 100,000 hours

* Cool Operating Temperature Less than 25 Degrees C

DIGITAL MICROSCOPE PREPARATION

Check the focus adjustment. The oversized knobs are designed for better

gripping. The focus knob should turn easily to change the focus, but the stage

will not drift or slip on its own.

Check the stage stop safety feature. This has been preset from the

factory and should not need adjustment. However, when checking be sure the

stage moves up and down when turning the focusing knob. The stage stop is a

thumb screw with a lock nut found just behind the stage. To check the stop, first

place a prepared slide in position for viewing. With the 4x objective in position

for viewing, move the focus knob until the stage is as high as it can be. Turn the

40x objective into place. This objective should be very close to the slide, but not

touching.

OPERATION

Loading the Software:

Simply insert CD-Rom provided into your CD-Rom drive and select Vision

Viewer/Pupil CAM drivers. Next, select Install drivers then install drivers. Then

follow the prompts. For more detailed information, please refer to the software

instruction manual.

Andere Handbücher für PrepScope T-1252

Andere Ken A Vision Mikroskop Handbücher

Ken A Vision

Ken A Vision T-1922C Bedienungsanleitung

Ken A Vision

Ken A Vision T-2701 Bedienungsanleitung

Ken A Vision

Ken A Vision Comprehensive Scope 2 T-19011C Bedienungsanleitung

Ken A Vision

Ken A Vision Professor ESH101 Bedienungsanleitung

Ken A Vision

Ken A Vision Comprehensive Scope T-1901 Bedienungsanleitung

Ken A Vision

Ken A Vision Professor ESH101 Bedienungsanleitung

Ken A Vision

Ken A Vision Microprojector 2 Bedienungsanleitung

Ken A Vision

Ken A Vision Comprehensive Scope 2 T-19011C Bedienungsanleitung

Ken A Vision

Ken A Vision PrepScope T-1201C Betriebsanleitung

Ken A Vision

Ken A Vision PrepScope 2 T-12011C Bedienungsanleitung

Ken A Vision

Ken A Vision T-1931C Bedienungsanleitung

Ken A Vision

Ken A Vision Video Flex® except 2000 series Bedienungsanleitung

Ken A Vision

Ken A Vision Comprehensive T-1901C Bedienungsanleitung

Ken A Vision

Ken A Vision X2000 Handbuch

Ken A Vision

Ken A Vision Comprehensive Scope 2 Bedienungsanleitung

Ken A Vision

Ken A Vision T-1941 Bedienungsanleitung

Ken A Vision

Ken A Vision Comparison Scope 2 T-19241C Bedienungsanleitung

Ken A Vision

Ken A Vision Dual Purpose Scope 2 Bedienungsanleitung

Ken A Vision

Ken A Vision Comparison Scope T-1924C Bedienungsanleitung

Ken A Vision

Ken A Vision Research Scope T-29041 Bedienungsanleitung

Ken A Vision

Ken A Vision T-1955 Bedienungsanleitung

Ken A Vision

Ken A Vision VisionScope T-2400 Bedienungsanleitung

Ken A Vision

Ken A Vision Comprehensive T-1901C Bedienungsanleitung

Ken A Vision

Ken A Vision VisionScope 2 T-22001 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung