KERN Optics OZO-5 Bedienungsanleitung

OZO-5_OZP-5-BA-e-1510

KERN & Sohn GmbH

Ziegelei 1

D-72336 Balingen

E-mail: [email protected]

Tel: +49-[0]7433- 9933-0

Fax: +49-[0]7433-9933-149

Internet: www.kern-sohn.com

User instructions

Stereo zoom microscope

KERN OZO-5, OZP-5

OZO 551, OZO 552, OZO 553, OZO 554

OZP 555, OZP 556, OZP 557, OZP 558

Version 1.0

01/2015

OZO-5_OZP-5-BA-e-1510 2

KERN OZO-5, OZP-5

Version 1.0 01/2015

User instructions

Stereo zoom microscope

Table of contents

1Before use....................................................................................3

1.1 General notes............................................................................................................................ 3

1.2 Notes on the electrical system................................................................................................ 3

1.3 Storage ...................................................................................................................................... 4

1.4 Maintenance and cleaning....................................................................................................... 5

2Nomenclature...............................................................................6

3Basic data.....................................................................................8

4Assembly......................................................................................9

5Operation and functionality.......................................................11

5.1 Getting started........................................................................................................................ 11

5.2 Adjust the interpupillary distance ........................................................................................ 11

5.3 Adjusting the magnification.................................................................................................. 11

5.4 Dioptre adjustment and focussing ....................................................................................... 12

5.5 Adjusting the stand................................................................................................................ 13

5.6 Using eye cups / High Eye Point eyepieces ........................................................................ 14

5.7 Brightness adjustment........................................................................................................... 15

5.8 Using external illumination units.......................................................................................... 16

5.9 Fitting and adjusting a camera ............................................................................................. 17

5.10 Using additional accessories................................................................................................ 19

5.11 Changing the bulb.................................................................................................................. 21

5.12 Changing the fuse .................................................................................................................. 21

6Optical data ................................................................................22

7Features......................................................................................23

8Trouble shooting........................................................................25

9Service........................................................................................26

10 Disposal......................................................................................26

11 Further information....................................................................26

3 OZO-5_OZP-5-BA-e-1510

1 Before use

1.1 General notes

You must open the packaging carefully, to make sure that none of the accessories in

the packaging fall on the floor and get broken.

In general, microscopes should always be handled carefully because they are

sensitive precision instruments. When using or transporting the microscope it is

particularly important to avoid abrupt movements, as this may damage the optical

components.

You should also avoid getting dirt or finger prints on the lens surface, because in

most cases this will reduce image clarity.

To maintain the performance of the microscope, it must never be disassembled. So

components such as lenses and other optical elements should be left as they were

before use. Also the electrical parts in the base of the device must not be tampered

with, as in this area there is an additional risk of triggering an electric shock.

1.2 Notes on the electrical system

(OZO 552, OZO 554, OZP 556, OZP 558)

Before connecting to a mains power supply, you must make sure that you are using

the correct input voltage. The information to select the correct mains cable is located

on each device, on the rear of the product directly above the connection socket. You

must comply with this information. If you do not comply with these specifications, then

fires or other damage to the device could occur.

The main switch must also be switched off before the mains cable is connected. In

this way you will avoid triggering an electric shock.

If you are using an extension cable, then the mains cable you use must be earthed.

If the original fuse should blow, it must only be replaced by an appropriate fuse.

Suitable replacement fuses are included with the delivery.

When carrying out any procedures whereby you come into contact with the electrical

system of the device, such as, for example, changing the bulb or fuse, only carry out

these procedures when the power is disconnected.

OZO-5_OZP-5-BA-e-1510 4

1.3 Storage

You should ensure that the device is not exposed to direct sunlight, temperatures

which are too high or too low, vibrations, dust or a high level of humidity.

The ideal temperature range is between 0 and 40°C and a relative humidity of 85%

should not be exceeded.

The device should always be located on a rigid, smooth, horizontal surface.

For devices with pillar stands, the microscope holder must not be rotated back too

far. If you do this, there is a risk that the microscope could tip over.

When the microscope is not being used, you should fit the objective cap and cover

the microscope with the enclosed dust protective cover.

If the eyepieces are being stored separately, the protective caps must be fitted to the

tube connectors. In most cases, if dust and dirt gets inside the optical unit of a

microscope this can cause irreversible errors or damage.

The best way to store accessories which consist of optical elements, such as, for

example, eyepieces and objectives, is in a dry box with desiccant.

5 OZO-5_OZP-5-BA-e-1510

1.4 Maintenance and cleaning

In any event, the device must be kept clean and dusted regularly.

If any moisture should be occur, before you wipe down the device you must ensure

that the mains power is switched off (if lighting unit is fitted).

When glass components become dirty, the best way to clean them is to wipe them

gently with a lint-free cloth.

To wipe oil stains or finger prints off the lens surface, moisten the lint free cloth with a

mixture of ether and alcohol (70 / 30 ratio) and use this to clean the lens.

You must be careful when handling ether and alcohol, as these are highly flammable

substances. You must therefore keep it away from naked flames and electrical

devices which can be switched on and off, and only use it in well-ventilated rooms.

However organic solutions of this type should not be used to clean other components

of the device. This could lead to damage to the paint finish. To do this, it is sufficient

to use a neutral cleaning product.

You could also use the following cleaning products to clean the optical components:

Special cleaner for optical lenses

Special optical cleaning cloths

Bellows

Brush

When handled correctly and checked regularly, the microscope should give many

years of efficient service.

Should repairs still be necessary, please contact your KERN dealer or our Technical

Department.

OZO-5_OZP-5-BA-e-1510 6

2 Nomenclature

Using the OZP 558 as an example

(Trinocular / with lighting)

7 OZO-5_OZP-5-BA-e-1510

Rear view

OZO-5_OZP-5-BA-e-1510 8

3 Basic data

OZO-5 / OZP-5

Optical system

Greenough

Dimmable lighting

Yes

Tube

angled at 35°

Interpupillary distance

52 –76 mm

Dioptre adjustment

On both sides

Packaging dimensions WxDxH

370 x 330 x 385 mm

OZO-5

Magnification ratio

8.8:1

OZP-5

Magnification ratio

9.2:1

Standard configuration

Model

KERN

Tube

Eyepiece

Field of view

Objective

Zoom

Stand

Illumination

OZO 551

Binocular

HSWF 10x Ø 23 mm

Ø 28.75 –3.3

0.8x –7x

Pillar

OZO 552

Binocular

HSWF 10x Ø 23 mm

Ø 28.75 –3.3

0.8x –7x

Pillar

3W LED (reflected light); 3W LED

(transmitted light)

OZO 553

Trinocular

HSWF 10x Ø 23 mm

Ø 28.75 –3.3

0.8x –7x

Pillar

OZO 554

Trinocular

HSWF 10x Ø 23 mm

Ø 28.75 –3.3

0.8x –7x

Pillar

3W LED (reflected light); 3W LED

(transmitted light)

OZP 555

Binocular

HSWF 10x Ø 23 mm

Ø 38.3 –4.2

0.6x -5.5x

Pillar

OZP 556

Binocular

HSWF 10x Ø 23 mm

Ø 38.3 –4.2

0.6x -5.5x

Pillar

3W LED (reflected light); 3W LED

(transmitted light)

OZP 557

Trinocular

HSWF 10x Ø 23 mm

Ø 38.3 –4.2

0.6x -5.5x

Pillar

OZP 558

Trinocular

HSWF 10x Ø 23 mm

Ø 38.3 –4.2

0.6x -5.5x

Pillar

3W LED (reflected light); 3W LED

(transmitted light)

9 OZO-5_OZP-5-BA-e-1510

4 Assembly

The first step is to position the microscope stand on a firm, level surface. The term

stand covers the stand base (standing surface) as well as the metal pillar which is

connected to it.

The holder is already on pillar of the stand, but you must always check whether it is

fixed securely and that it is in the correct position (preferably centrally and facing to

the front).

Please see section 5.5 for more details on adjusting the stand.

The next step is to place the microscope head on the holder, by passing the

objective through the holder ring until the rest of the head is above the ring.

You must use the small silver adjusting screw on the front of the holder ring to fix the

head in place.

The alignment of the microscope head is left to the user to do and can be adjusted to

suit the individual application situations.

To make it easier to operate the focus wheels or lighting control for example, we

recommend that you position the head with the tube connectors centrally to the front.

Ideally, the holder and head are then parallel on the central axis of the stand base

(see figure on page 10).

Then you can remove the protective caps from the tube connectors so that you can

then fit the eyepieces. When doing this, please be particularly careful that you do

not touch the optical lenses with your fingers and that no dust enters the

apertures.

You should also never fit two eyepieces with different magnifications.

With regard to the use of a device with lighting (OZO 552, OZO 554, OZP 556, OZP

558) you must make sure that the frosted glass stand inlay is fitted in the centre

of the stand base, so that the transmitted light can be used correctly.

Also, when using reflected light please make sure, that the connection cable

between the holder and upper side of the pillar is plugged in.

Additional optional attachments:

The eye cups supplied with the microscopes can be fitted to the eyepieces.

(see section 5.6).

You can fit a C-mount adapter to the appropriate connection point on the top

of the microscope head for trinocular devices (OZO 553, OZO 554, OZP 557,

OZP 558). This enables you to fit and use digital cameras. (remove protective

cap first) (see section 5.9).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KERN Optics Mikroskop Handbücher

KERN Optics

KERN Optics OBL-14 Bedienungsanleitung

KERN Optics

KERN Optics OBD 127 Bedienungsanleitung

KERN Optics

KERN Optics OZL 46 Series Bedienungsanleitung

KERN Optics

KERN Optics OBN-13 Bedienungsanleitung

KERN Optics

KERN Optics OIV-6 Bedienungsanleitung

KERN Optics

KERN Optics OBF-1 Bedienungsanleitung

KERN Optics

KERN Optics OBE 121 Bedienungsanleitung

KERN Optics

KERN Optics OCM 161 Bedienungsanleitung

KERN Optics

KERN Optics OBD-1 Bedienungsanleitung

KERN Optics

KERN Optics OKN-1 Bedienungsanleitung

KERN Optics

KERN Optics OZL-9 Bedienungsanleitung

KERN Optics

KERN Optics OZM-98 Series Bedienungsanleitung

KERN Optics

KERN Optics OZM 912UK Bedienungsanleitung

KERN Optics

KERN Optics OZM-9 Series Bedienungsanleitung

KERN Optics

KERN Optics OZM-5 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

KERN Optics

KERN Optics OBT 101 Bedienungsanleitung

KERN Optics

KERN Optics OBE 1 Bedienungsanleitung

KERN Optics

KERN Optics OKM-1 Bedienungsanleitung

KERN Optics

KERN Optics OBN-15 Bedienungsanleitung

KERN Optics

KERN Optics OSE-42 Bedienungsanleitung

KERN Optics

KERN Optics OSF-4G Bedienungsanleitung

KERN Optics

KERN Optics OZL-47 Bedienungsanleitung

KERN Optics

KERN Optics OBN132 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung

AO Cycloptic Bedienungsanleitung