Kohler K-45210 Montageanleitung

Installation and Care Guide

Shower Column

Mproduct numbers are for Mexico (i.e., K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-45209 K-45210

K-45211 K-45212

1213116-2-A

Tools and Materials

Before You Begin

NOTE: This guide includes the installation sequence for the shower

column only. Install the mixing valve, mixing valve trim, and spout

according to the manufacturer’s instructions.

NOTICE: Risk of product damage. Do not apply excessive weight

or downward force to the shower column.

CAUTION: Risk of property damage. Water leakage may

occur if supply piping allows movement. Ensure the supply

piping and 1/2″-14 NPT elbow ﬁtting are securely fastened to

braces in the stud framing.

NOTE: The showerhead, hose, and handshower are purchased

separately.

Please read all instructions before you begin.

Observe all local plumbing and building codes.

Shut off the water supply.

Inspect the existing supply piping and wall materials. Replace if

necessary.

Sealant Tape

3/8"

100% Silicone Sealant

1/2"

Phillips

Screwdriver

1213116-2-A 2 Kohler Co.

Before You Begin (cont.)

The shower column is supplied with toggle anchor fasteners for

installation onto a ﬁnished wall surface. The ﬁnished wall

thickness must be a minimum of 5/8″(16 mm) and must be

adequate in strength. Two toggle anchor fasteners are required

per mounting collar.

IMPORTANT! If the supplied toggle anchor fasteners are not used

to install the shower column:

Ensure that adequate strength wall backing materials and stud

bracing are properly positioned behind the ﬁnished wall.

Obtain proper fasteners (not provided) taking into account the

type of stud bracing material and thickness of the mounting

collar, ﬁnished wall, wall backing, and stud bracing.

Fasteners must be corrosion-resistant and capable of 300 lbs (136

kg) load bearing per fastener.

A minimum of two fasteners are required per mounting collar.

Fasteners must be securely anchored into the stud bracing to

adequately support the product.

IMPORTANT! For retroﬁt/remodel installations: Check the existing

shower enclosure for adequate clearances before proceeding with the

shower column installation. Refer to the Roughing-in for the shower

column and showerhead.

Verify the distances between:

•The ceiling and the center of the existing shower arm at the

ﬁnished wall surface.

•The shower ﬂoor and the center of the existing shower arm at the

ﬁnished wall surface. Ensure sufficient clearance under the

showerhead.

•The center of the existing shower arm and the center of the

mixing valve trim.

Kohler Co. 3 1213116-2-A

Roughing-In - Upper Supply Connection

Measure the distance between the 1/2″-14 NPT elbow and the

ﬁnished wall surface. The distance must be between 1-3/8″(35

mm) and 2-7/8″(73 mm).

IMPORTANT! The shower column connection will not seal

properly if the distance exceeds 2-7/8″(73 mm); see below for the

required deep roughing-in kit.

If the distance is between 2-7/8″(73 mm) and 4″(102 mm):

Order the 1194630 Deep Roughing-in Kit.

If the distance is less than 1-3/8″(35 mm): Order the 1187917

Shallow Roughing-in Kit.

1" (25 mm) Maximum

Wall Surface Offset

1/2"-14 NPT Elbow

1-3/8" (35 mm) –

2-7/8" (73 mm)

1-3/4" (44 mm) Minimum

Escutcheon Clearance

Finished Wall Surface

1213116-2-A 4 Kohler Co.

Roughing-In

Backing

Material

3-3/4"

(95 mm)

27"

(686 mm)

18-5/8" (473 mm)

9-1/2"

(241 mm)

75" (1905 mm)

Recommended

72" (1829 mm)

Minimum

80" (2032 mm)

Recommended

75" (1905 mm)

Minimum Backing

Material

6" (152 mm)

Minimum

27"

(686 mm)

6" (152 mm)

Minimum

K-45210 (Less Showerhead, Handshower, and Hose)

K-45209 (Less Showerhead, Handshower, and Hose)

Kohler Co. 5 1213116-2-A

Roughing-In

18"

(457 mm)

18-5/8" (473 mm)

Backing

Material

Backing

Material

18"

(457 mm)

9-1/2"

(241 mm)

18-5/8" (473 mm)

75" (1905 mm)

Recommended

72" (1829 mm)

Minimum

3-3/4"

(95 mm)

78" (1981 mm)

Recommended

75" (1905 mm)

Minimum

6" (152 mm)

Minimum

6" (152 mm)

Minimum

K-45212 (Less Showerhead, Handshower, and Hose)

K-45211 (Less Showerhead, Handshower, and Hose)

1213116-2-A 6 Kohler Co.

1. Retroﬁt/Remodel Installation

CAUTION: Risk of property damage. Water leakage may

occur if supply piping allows movement. Ensure the supply

piping and 1/2″-14 NPT elbow ﬁtting are securely fastened to

braces in the stud framing.

IMPORTANT! Check the existing shower enclosure for adequate

clearances as described in section ″Before You Begin.″

Remove the existing showerhead and shower arm escutcheon.

Carefully push the existing shower arm toward the ﬁnished wall

surface.

Check for inward movement of the supply piping.

If inward movement is possible, securely fasten the supply piping

to braces in the stud framing before beginning the shower column

installation.

Remove the existing shower arm.

Measure the existing shower arm hole. Ensure that the ﬁnished

wall material has an upper supply connection hole diameter

between 1″(25 mm) minimum and 1-1/4″(32 mm) maximum,

and the hole is centered on the outlet of the 1/2″-14 NPT elbow

ﬁtting. Repair the wall surfaces if the existing shower arm hole is

not centered or exceeds the recommended dimensions.

Supply Piping

1/2"-14 NPT Elbow

Kohler Co. 7 1213116-2-A

2. Install the Supply Adapter

For New Construction Installations

CAUTION: Risk of property damage. Water leakage may

occur if supply piping allows movement. Ensure the supply

piping and 1/2″-14 NPT elbow ﬁtting are securely fastened to

braces in the stud framing.

IMPORTANT! This guide includes the installation sequence for the

shower column only. Refer to the manufacturer’s instructions for

installation of the mixing valve, mixing valve trim, and spout.

Rough-in the mixing valve, supply piping, and bath spout

connection appropriate for your installation.

Refer to the ″Roughing-in″section in this guide for proper

location of the 1/2″-14 NPT elbow ﬁtting inside the wall.

Ensure that the supply piping and 1/2″-14 NPT elbow ﬁtting are

securely fastened to the stud framing.

3/8" Hex

Wrench

Supply

Adapter

1" (25 mm)

Minimum –

1-1/4" (32 mm)

Maximum

1/2"-14 NPT Elbow

Supply Piping

1213116-2-A 8 Kohler Co.

Install the Supply Adapter (cont.)

Ensure that the ﬁnished wall material has an upper supply

connection hole diameter between 1″(25 mm) minimum and

1-1/4″(32 mm) maximum, and the hole is centered on the outlet

of the 1/2″-14 NPT elbow ﬁtting.

If your supply connection hole diameter is between 1-1/4″(32

mm) and 2-1/4″(57 mm): Order the 1194302 Large

Escutcheon/Mounting Collar Kit.

Install the ﬁnished wall material.

Install the mixing valve trim and bath spout according to the

manufacturer’s instructions.

For New Construction and Retroﬁt Installations

Apply sealant tape to the supply adapter thread.

The supply adapter has an internal 3/8″hex socket. Thread the

supply adapter into the 1/2″-14 NPT elbow using a 3/8″hex

wrench.

Kohler Co. 9 1213116-2-A

3. Mark the Mounting Hole Locations

NOTE: The upper mounting collar must be centered on the supply

adapter. The distance between the upper and lower mounting collar

centers should be 18″(457 mm) or 27″(686 mm) depending on the

length of your shower column.

Center the mounting collar on the supply adapter. Mark the left

and right mounting holes.

For K-45209/K-45210 only: From the center of the supply adapter,

measure down 27″(686 mm) and mark the horizontal

measurement with a pencil.

For K-45211/K-45212 only: From the center of the supply adapter,

measure down 18″(457 mm) and mark the horizontal

measurement with a pencil.

Center the mounting collar on the horizontal line. Measure and

mark the left and right mounting holes. Ensure the upper and

lower mounting hole locations are level and plumb to one

another.

Do not drill the mounting holes until instructed to do so.

2" (51 mm)

Supply Adapter

Mounting Collar

K-45209, K-45210,

27" (686 mm)

K-45211, K-45212,

18" (457 mm)

1213116-2-A 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-26228T Bedienungsanleitung

Kohler

Kohler K-15886 Montageanleitung

Kohler

Kohler Sterling TS27370-4G Bedienungsanleitung

Kohler

Kohler K-10121 Bedienungsanleitung

Kohler

Kohler K-9486 Bedienungsanleitung

Kohler

Kohler MEMOIRS Series Bedienungsanleitung

Kohler

Kohler Kumin K-103K36-SANA-CP Bedienungsanleitung

Kohler

Kohler 8030A Bedienungsanleitung

Kohler

Kohler K-20099T-Y Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler Purist K-T14428 Bedienungsanleitung

Kohler

Kohler EVOKE 6332T-B4 Bedienungsanleitung

Kohler

Kohler Mira Logic L19B Bedienungsanleitung

Kohler

Kohler Wave Series Bedienungsanleitung

Kohler

Kohler K-3396 Montageanleitung

Kohler

Kohler K-T195 Montageanleitung

Kohler

Kohler K-15003 Bedienungsanleitung

Kohler

Kohler K-13132-3A Montageanleitung

Kohler

Kohler Karbon K-6227A Bedienungsanleitung

Kohler

Kohler 74036T-4E2 Bedienungsanleitung

Kohler

Kohler STANCE K-37467T Bedienungsanleitung

Kohler

Kohler 13EOZD Bedienungsanleitung

Kohler

Kohler K-2191 Bedienungsanleitung

Kohler

Kohler K-6330 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung