Kohler K-116 Bedienungsanleitung

Installation Guide

Widespread Lavatory Faucets

K-116, K-432, K-454,

K-6813, K-7304, K-7435,

K-8211, K-8212, K-10269,

K-10272, K-10273, K-10577,

K-10578, K-11076, K-11551,

K-12265, K-15261, K-15265,

K-15816

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1002628-2-P

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Assorted

Screwdrivers Adjustable

Wrench

Plumbers Putty Sealant Tape

Heavy Duty Pipe

Sealant with Teflon

1002628-2-P 2 Kohler Co.

1. Spout Installation

Apply a bead of plumbers putty or other sealant to the underside

of the spout or putty ring (if supplied) according to the putty

manufacturer’s instructions.

Locate the center hole and insert the spout.

NOTE: For a thin-walled lavatory (such as stainless steel), slide the

washer and nut onto the spout shank. Securely tighten the nut with

a wrench. Do not overtighten.

Slide the metal washer and nut onto the spout shank.

Position the metal washer so the second hole lines up with the

drain lift rod hole on the back of the spout.

Securely tighten the nut with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Apply plumbers

putty.

Putty Ring

(if included)

Metal

Washer

Nut

Kohler Co. 3 1002628-2-P

2. Handle Valve Installation

NOTE: The valve body marked ″COLD″(with blue lettered tape

attached to the tube) should be installed to the right of the faucet.

Apply a bead of plumbers putty or other sealant to the underside

of the escutcheons according to the manufacturer’s instructions.

Insert the valve bodies into the proper mounting holes.

Install a washer and a nut onto the underside of each valve body.

Rotate each valve body until the copper tubing faces toward the

outside of the lavatory.

While holding the valve bodies in place, securely tighten the

locknuts with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Handle

Escutcheon

Apply plumbers

putty.

Valve Body

Copper

Tube

Nut

Washer

1002628-2-P 4 Kohler Co.

3. Supply Tee and Hose Installation

Insert the plastic gasket and the rubber washer into the supply

tee.

Thread the supply tee onto the spout shank until hand-tight.

Ensure that the arms of the supply tee are aligned to face the left

and right sides of the lavatory.

Thread a ﬂexible hose onto each handle valve outlet. Securely

tighten the hose with a wrench. Do not overtighten.

Connect the ﬂexible hoses to the supply tee. Do not use thread

sealant. To avoid kinking the hoses, loop them.

Securely tighten the hose with a wrench. Do not overtighten.

Hose

O-Ring

End Body Outlet

End Body

Supply Tee

Flexible Hose

Gasket

Rubber Washer

Kohler Co. 5 1002628-2-P

4. Install the Drain

Remove the plastic cap from the drain assembly.

Remove the stopper from the ﬂange.

Remove the ﬂange from the drain body.

Thread the body nut down the drain body.

Slide the seal down to the body nut.

From underneath the lavatory, insert the drain body through the

drain hole.

Apply plumbers putty to the underside of the ﬂange.

Thread the ﬂange onto the top of the drain body.

Thread the body nut up the drain body until the seal is

compressed against the underside of the lavatory.

Wipe away any excess plumbers putty from around the ﬂange.

Remove the rod nut from the drain body.

Remove the clip from the rod.

Body Nut

Stopper

Stopper Bolt

Plastic Cap

Lift Rod

Flange

Drain Body

Tailpiece

Seal

Rod

Clip

Rod Nut

Link

Thumbscrew

1002628-2-P 6 Kohler Co.

Install the Drain (cont.)

Insert the short end of the rod into the seal hole and under the

stopper. Loosely secure in place with the rod nut.

Push the rod down to open the drain.

Insert the stopper into the drain assembly.

Remove and adjust the stopper so it lifts approximately 3/8″(1

cm) when opened. To adjust, hold the stopper bolt and turn the

stopper counterclockwise to raise and clockwise to lower.

Reinstall the stopper.

For Vandal-Resistant Installations: Remove the rod nut. While

the stopper is in place, insert the end of the rod through the hole

in the stopper bolt. Secure the rod with the rod nut.

For All Other Installations: Tighten the rod nut to secure the rod.

Identify the best hole in the link to allow full operation of the rod

and the lift rod.

Align the link hole with the rod and slide the clip and the link

onto the rod with the thumbscrew facing the back of the lavatory.

To move the link to the proper position, squeeze the clip and

slide it along the rod.

Align the link with the faucet lift rod and push the lift rod

through the hole in the link. If required, loosen the thumbscrew

on the link.

Verify that the lift rod knob rests on the escutcheon when the

drain is in the full open position.

Tighten the thumbscrew to secure the lift rod position.

Kohler Co. 7 1002628-2-P

5. Supply Connections

Install the lavatory using the lavatory manufacturer’s instructions.

Connect the supply tubes to the handle valve inlets, and to the

supply stops. Left is hot and right is cold.

Tighten all connections.

Supply

Tube

Valve

Inlet

Shut-off

Valve

1002628-2-P 8 Kohler Co.

6. Installation Checkout

Connect the tailpiece and P-trap (as needed).

Ensure that all connections are tight.

Remove the aerator by turning it counterclockwise.

Open the drain.

Turn on the main water supply and check for leaks. Adjust as

needed.

Open both hot and cold valves and run water through the spout

for about a minute to remove debris. Check for leaks. Turn the

faucet off.

Remove any debris from the aerator and reinstall.

Spout

Aerator

Kohler Co. 9 1002628-2-P

Guide d’installation

Robinets de lavabo à large entraxe

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation ou d’alimentation

d’eau sont endommagés.

Replacer les tubes d’alimentation ou d’évacuation si nécessaire.

Pour les nouvelles installations, installer le robinet avant

d’installer le lavabo.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Tournevis assortis Clé à molette

Mastic de plomberie Ruban d'étanchéité

pour filetage

Pâte d'étanchéité pour

tuyaux au Téflon

Kohler Co. Français-1 1002628-2-P

Andere Handbücher für K-116

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-18485 Montageanleitung

Kohler

Kohler Carillon K-7806-95 Bedienungsanleitung

Kohler

Kohler Clearflo K-7160-TF Montageanleitung

Kohler

Kohler HYDRO-TOWER 100 K-6281T-NA Bedienungsanleitung

Kohler

Kohler Sterling 20243 Montageanleitung

Kohler

Kohler Sunstruck K-24008-GH Bedienungsanleitung

Kohler

Kohler K-10540 Montageanleitung

Kohler

Kohler K-4350 Series Montageanleitung

Kohler

Kohler K-T14419 Montageanleitung

Kohler

Kohler K-7653 Montageanleitung

Kohler

Kohler K-10481 Bedienungsanleitung

Kohler

Kohler ELLISTON 75522T-4 Bedienungsanleitung

Kohler

Kohler K-14402 Bedienungsanleitung

Kohler

Kohler AIRFOIL 37271X-7 Bedienungsanleitung

Kohler

Kohler Sterling 225C7 Montageanleitung

Kohler

Kohler 99721T-4 Bedienungsanleitung

Kohler

Kohler K-T10277 Montageanleitung

Kohler

Kohler K-8816 Bedienungsanleitung

Kohler

Kohler K-6665 Bedienungsanleitung

Kohler

Kohler K-10268 Bedienungsanleitung

Kohler

Kohler Memoirs K-T448 Montageanleitung

Kohler

Kohler KUMIN 18655T-CP Bedienungsanleitung

Kohler

Kohler K-9245 Montageanleitung

Kohler

Kohler K-10430 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung