Kohler K-697 Montageanleitung

Homeowners Guide

Concentric Thermostatic Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-697, K-698

1066046-5-B

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

CAUTION: Risk of scalding hazard. This device has been

calibrated at the factory to ensure a safe maximum water

temperature. Any variance in settings or water inlet

conditions from those used during factory calibration may

raise the discharge temperature above the safe limit, and may

present a scalding hazard.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

The installer is responsible for adjusting the maximum water

temperature of this valve according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the temperature adjustment

instructions in this document, in the United States please contact our

Customer Service Department at 1-800-4KOHLER. Outside the U.S.,

please contact your distributor.

IMPORTANT NOTICE: Please ﬁll in the blanks in the information box

in the Homeowners Guide and on the valve label. Retain the

Homeowners Guide for future reference.

•The maximum temperature is calibrated so the outlet water

temperature does not exceed 120°F (49°C).

•Factory calibrated inlet conditions are:

Hot and cold water pressure = 45 psi (3.2 kg/cm

)

Hot water supply temperature = 145°F (63°C)

Cold water supply temperature = 65°F (18°C)

•If inlet conditions differ from those used during factory

calibration, it may be necessary to re-calibrate the valve after

installation. The installer must check the mixed ﬂow

temperature after installation, and adjust the valve as needed

according to the instructions.

1066046-5-B 2 Kohler Co.

IMPORTANT INSTRUCTIONS (cont.)

NOTICE TO HOMEOWNERS! This device has been preset by

_______________________ of _______________________________ to

ensure a safe maximum temperature. Any change in the setting may

raise the discharge temperature above the limit considered safe, and

lead to scalds.

Date: ______________

Thank You For Choosing Kohler Company

Thank you for choosing Kohler Company. Your Kohler Company

product reﬂects the true passion for design, craftsmanship, artistry, and

innovation Kohler Company stands for. We are conﬁdent its

dependability and beauty will surpass your highest expectations,

satisfying you for years to come.

All information in this guide is based upon the latest product

information available at the time of publication. At Kohler Company,

we strive to fulﬁll our mission of improving the level of gracious living

for each person who is touched by our products and services. We

reserve the right to make changes in product characteristics, packaging,

or availability at any time without notice.

Kohler Co. 3 1066046-5-B

Integral Supply Stop Operation

NOTE: Use a 3/8″square drive or 10 mm hex wrench to adjust the

stops.

Turn Off the Stops

Use a 3/8″square drive or 10 mm hex wrench to turn the integral

stops 90° counterclockwise to shut off both the hot and cold water

inlet supplies.

NOTE: If the integral stop turns, but the outer ring does not turn,

ﬁrmly tighten (clockwise) the integral stop. Then rotate

counterclockwise. The outer ring should then turn with the integral

stop.

Conﬁrm the stops are closed using the diagram above.

Turn the ﬂow control counterclockwise to release excess water.

The cartridge may now be removed for servicing or replacement.

NOTE: Keep a rag handy to catch excess water that will gradually

drain when valve cartridge is removed.

Off On

Integral Stop

1066046-5-B 4 Kohler Co.

Integral Supply Stop Operation (cont.)

Service the Stops

NOTE: Keep a rag handy to catch excess water that will gradually

drain when stop cartridge is removed.

Turn off both the hot and cold water at the nearest supply

shut-off or water main.

Verify that the water is off before continuing.

For models with a locking bar, loosen the two screws, slide the

locking bar up until it is clear of the stops, and tighten the screws

to keep the locking bar from sliding back down.

Use a 3/8″square drive or 10 mm hex wrench to remove the stop

assemblies.

Thread the new stop assemblies into the valve and tighten.

Open the stops using a 3/8″square drive or 10 mm hex wrench.

Loosen the screws on the locking bar and slide it down.

Tighten the screws.

Turn on the hot and cold water supplies.

Check for leaks.

Kohler Co. 5 1066046-5-B

Servicing the Filters

Turn off the water supply.

Remove the trim.

Close the stops following the directions in the previous section.

NOTE: 1/2″models do not have a locking assembly, 3/4″model

shown.

Insert a 3/8″square drive or 10 mm a hex wrench into the

appropriate stop (hot is left side, cold is right side) and remove it.

Remove the screen assembly by turning clockwise.

Clean or replace the screen assembly as needed.

Rotate the ﬂow control clockwise 90° to close it.

Install the screen to the stop assembly.

Reinstall the screen assembly by pushing in and turning

counterclockwise.

Open the supply stops and check for leaks.

Reinstall the trim.

Stop and Screen

Assembly

Twist toward notch.

Remove screen.

1066046-5-B 6 Kohler Co.

Check the Maximum Water Temperature

CAUTION: Risk of personal injury. If the maximum water

temperature is above 120°F (49°C) the water temperature

must be reset to 120°F (49°C) or below to minimize scalding

hazards. Do not set the water temperature above 120°F

(49°C). Setting the water temperature at or below this

temperature will minimize the risk associated with scalding

hazards.

Turn on the water supply if it is not already on.

Remove the plaster guard.

Turn the water to full hot by turning the handle counterclockwise

until it stops.

Let the water run for at least two minutes.

Use a thermometer to determine the temperature. Make sure the

maximum temperature is below 120°F (49°C).

Turn counterclockwise

to open water flow.

Turn temperature

counterclockwise to hot.

Temporary

Shutoff Knob

Kohler Co. 7 1066046-5-B

Maximum Hot Water Adjustment

Turn the valve off.

Remove the trim or mud guard if present.

Remove the stem screw. Do not remove the stem adapter.

NOTE: The spline adapter will most likely stay inside the stem

adapter. Do not remove the spline adapter from the stem if it does

not remain in the stem adapter.

Insert the provided 2.5 mm hex wrench into the center of the

stem. Make sure it ﬁts snugly into the head of the hex screw at

the bottom of the stem.

Turn the hex screw clockwise to decrease the temperature,

counterclockwise to increase it.

Position the stem adapter on the stem and turn the water to full

hot.

Use a thermometer to determine the temperature of the water.

Repeat the adjustment with the hex wrench until the desired

temperature is attained.

Reinstall the screw and tighten.

Reinstall the trim.

Allow the water to ﬂow for several minutes to stabilize the water

temperature.

Loosen and remove screw.

Do not remove stem adapter.

Screw

Turn counterclockwise to

increase temperature.

Stem

Adapter

1066046-5-B 8 Kohler Co.

Troubleshooting

This troubleshooting guide is for general aid only. For warranty

service, contact your dealer or wholesale distributor.

Symptoms Probable Cause/Recommended

Action

1. Only hot or cold water from

outlet. A. Inlet supplies are reversed. See

″Reversed Inlet Supplies″section

of the valve Installation Guide.

B. No hot water reaching shower

control.

C. Check ﬁlter screens for

blockage.

2. Fluctuating or reduced ﬂow

rate. Normal function of thermostatic

control when operating conditions

are unsatisfactory.

A. Check ﬁlter screens for ﬂow

restriction.

B. Make sure that the minimum

ﬂow rate is sufficient for supply

conditions.

C. Make sure that inlet

temperature differentials are

sufficient.

D. Service stops are not fully

threaded in. Rotate both service

stops until fully threaded.

E. Service stops are not fully open.

Open them all the way.

F. Check thermostatic performance;

renew thermostatic cartridge, if

necessary.

3. No ﬂow from shower control

outlet. A. Check ﬁlter screens for

blockage.

B. Hot or cold supply failure;

thermostat holding correct

shutdown function.

C. Flow control cartridge does not

work. Check and replace if

necessary.

D. Service stops are shut off.

Rotate both stops

counterclockwise.

4. Blend temperature drift. Indicates operating conditions

changed.

Kohler Co. 9 1066046-5-B

Troubleshooting (cont.)

Symptoms Probable Cause/Recommended

Action

A. Refer to symptom 2 above.

B. Hot supply temperature

ﬂuctuation.

C. Supply pressure ﬂuctuation.

5. Maximum blend temperature

setting too hot or too cold. A. Indicates incorrect maximum

temperature setting; refer to the

″Adjust Temperature Settings″

section.

B. Refer to symptom 4 above.

6. Water leaking from the valve

body. Seal(s) worn or damaged.

A. Obtain service kit and replace

seal(s).

B. If leaking from around the

temperature spindle, replace the

thermostatic cartridge.

7. Flow knob or temperature

knob is stiff to operate. A. Impaired free movement of

internal components. Remove the

trim faceplate and reinstall with

the drive features aligned as

directed in the installation guide.

B. Replace the valve cartridge.

8. Flow control handle does not

move. A. Remove the ﬂow handle, rotate

the ﬂow control on the cartridge

clockwise to the ″OFF″position.

Turn it slightly counterclockwise

(about 5 degrees) and reinstall the

ﬂow handle. Conﬁrm the

temperature control is engaged

and test the operation of the

controls.

B. Replace the valve cartridge.

Lifetime Limited Warranty

KOHLER

Faucet Lifetime Limited Warranty

Kohler Co. warrants its Faucets* manufactured after January 1, 1997, to

be leak and drip free during normal residential use for as long as the

original consumer purchaser owns his or her home. If the Faucet

should leak or drip during normal use, Kohler Co. will, free of charge,

mail to the purchaser the cartridge necessary to put the Faucet in good

1066046-5-B 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Modernlife Touchless 77786K-TF-0 Bedienungsanleitung

Kohler

Kohler K-15182 Bedienungsanleitung

Kohler

Kohler K-13132-3A Montageanleitung

Kohler

Kohler K-15003 Bedienungsanleitung

Kohler

Kohler 45541A-0 Bedienungsanleitung

Kohler

Kohler Mira Atom ERD Bedienungsanleitung

Kohler

Kohler Wave 12791T-4 Bedienungsanleitung

Kohler

Kohler K-994 Bedienungsanleitung

Kohler

Kohler K-7779 Montageanleitung

Kohler

Kohler K-2271 Bedienungsanleitung

Kohler

Kohler K-2277 Bedienungsanleitung

Kohler

Kohler K-45415 Montageanleitung

Kohler

Kohler MasterShower K-T9472 Bedienungsanleitung

Kohler

Kohler K-T9493 Bedienungsanleitung

Kohler

Kohler ALEO Bedienungsanleitung

Kohler

Kohler Flipside 15596T Bedienungsanleitung

Kohler

Kohler K-1124-G Kurzanleitung

Kohler

Kohler K-616 Montageanleitung

Kohler

Kohler Fluence K-702221-6L Bedienungsanleitung

Kohler

Kohler K-106 Montageanleitung

Kohler

Kohler KT6908 Bedienungsanleitung

Kohler

Kohler K-1418-GCR Kurzanleitung

Kohler

Kohler K-5805 Montageanleitung

Kohler

Kohler K-5415 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung