Kohler K-T309 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-T309 K-T312

K-T313

1023642-2-C

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this valve according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1023642-2-C 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

CAUTION: Risk of product damage to the K-306-KS valve

assembly. When using this valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

We recommend that you determine if the maximum water

temperature is acceptable before installing this trim. If

temperature adjustment is needed, refer to the ″Water

Temperature Adjustment″section.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″Off″

position.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Thermometer

Strap

Wrench Thread

Sealant

Plumbers

Putty Hex

Wrench

Assorted

Screwdrivers

Kohler Co. 3 1023642-2-C

1. Install the Spout

Remove the temporary nipple.

Apply thread sealant and install a 1/2″nipple so it extends 1/2″

(1.3 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant around the inlet

end of the spout according to the manufacturer’s instructions.

Apply thread sealant to the nipple and thread the spout onto the

nipple.

Carefully tighten with a clean strap wrench.

Remove all excess putty.

Nipple Spout

1/2"

(1.3 cm)

Apply

plumbers

putty.

1023642-2-C 4 Kohler Co.

2. Install the Showerhead

CAUTION: Risk of product damage. To avoid plugging the

showerhead spray outlets, use thread sealant tape on the shower

arm threads. Do not use thread sealant compound (pipe dope).

Remove the temporary nipple from the shower elbow.

Apply thread sealant tape and install a 1/2″NPT nipple to

extend 1/2″(1.3 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant to the back of

the shower arm according to the manufacturer’s instructions.

Apply thread sealant tape to the nipple and thread the shower

arm onto the nipple.

Carefully tighten with a clean strap wrench.

Remove all excess putty.

With the showerhead off, ﬂush out the system.

Apply thread sealant tape to the shower arm, and thread the

showerhead to the shower arm.

1/2"

(1.3 cm)

Nipple

Showerhead

Apply

plumbers

putty.

Shower

Arm

Kohler Co. 5 1023642-2-C

3. Water Temperature Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature.

Complete the information on the valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

1023642-2-C 6 Kohler Co.

4. Diverter Assembly

For Valves With a Diverter

Remove and discard the plaster guard and/or dome, if installed.

Position the actuator over the diverter stem. Tighten the setscrew.

Slide the guide over the actuator and thread it onto the diverter

stem.

For All Models

Remove and discard the plaster guard and/or dome if they are

installed.

Slide the faceplate over the valve stem.

Set the shroud against the faceplate.

Discard plaster

guard with dome.

Diverter

Stem

Actuator

Installations with a Diverter

Guide

Setscrew

Valve Stem

Discard plaster

guard with dome.

Valve Stem

Shroud

Faceplate

All Models

Kohler Co. 7 1023642-2-C

5. Install the Handle

CAUTION: Risk of product damage to the K-306–KS valve

assembly. When using this valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Remove the sleeve from the handle assembly.

Set the sleeve into the center of the shroud with the screw holes

aligned.

Secure the sleeve with two screws.

If you have a thin wall installation, remove the large and small

bearings from the long stem extension.

Reinstall the large and small bearing and washers onto the short

stem extension.

Secure the chosen stem extension into the handle assembly with a

screw.

Thread the handle assembly over the sleeve, and securely hand

tighten.

Sleeve

Screws

Screw

Short Stem Extension

Small Bearing

Large Bearing

Washers

Handle Assembly

Long Stem

Extension

1023642-2-C 8 Kohler Co.

Guide d’installation

Garniture de baignoire mono-contrôle et de

douche

INSTRUCTIONS IMPORTANTES

À LIRE ET À LAISSER AU CLIENT

AVERTISSEMENT : Risque de brûlures ou de blessures graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition de débit

croisé au régulateur et modiﬁer la température de l’eau.

•Les facteurs qui changent la température de l’eau fournie à cette

valve, tels que les changements de température d’eau saisonniers,

et le remplacement ou l’entretien du chauffeau, changeront la

température maximale de l’eau fournie par le régulateur et

pourront présenter un danger de brûlures.

•La valve à pression équilibréene compensera pas les changements

de température d’alimentation d’eau; ajuster la température

maximale de cette valve à pression équilibrée si de tels

changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de cette valve selon les

instructions.

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

S’il ne vous est pas possible de comprendre les instructions

d’installation ou de réglage de la température données par ce

document, veuillez contacter notre département du service clientèle

aux États-Unis.1-800-4-KOHLER. Hors des États-Unis, veuillez

contacter votre distributeur.

Kohler Co. Français-1 1023642-2-C

INSTRUCTIONS IMPORTANTES (cont.)

AVIS IMPORTANT AUX INSTALLATEURS! Veuillez remplir le

coupon dans le guide du propriétaire ainsi que sur l’étiquette de la

valve. Conserver le guide du propriétaire pour future référence.

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de commencer

ATTENTION : Risque d’endommagement de l’ensemble de

valve K-306KS. Lorsque cette valve est utilisée en installation

ﬁbres de verre ou acrylique, utiliser le kit d’installation de mur

ﬁn (88526).

Respecter tous les codes de plomberie et de bâtiment locaux.

Le mur ﬁni ou la baignoire/douche doit être installé avant

d’installer cette garniture.

Nous conseillons de déterminer si la température maximale de

l’eau est acceptable avant d’installer la garniture. S’il un réglage

de température est nécessaire, se réferer à la section ″Réglage de

la température d’eau″.

Thermomètre

Clé à

sangle Joint

d'étanchéité

pour filetage

Mastic de

plombier Clé

hexagonale

Tournevis

assortis

1023642-2-C Français-2 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-5665 Montageanleitung

Kohler

Kohler KARAT K-23883 Bedienungsanleitung

Kohler

Kohler K-6448 Montageanleitung

Kohler

Kohler K-1124-G Kurzanleitung

Kohler

Kohler Supply K-13724 Bedienungsanleitung

Kohler

Kohler K-11618 Bedienungsanleitung

Kohler

Kohler K-10121 Bedienungsanleitung

Kohler

Kohler VIA Series Service-Handbuch

Kohler

Kohler K-14663 Montageanleitung

Kohler

Kohler K-3820 Montageanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler STRAYT 37341-4 Bedienungsanleitung

Kohler

Kohler ENGLEFIELD TAPWARE STUDIO 20149A-4 Bedienungsanleitung

Kohler

Kohler K-16230 Bedienungsanleitung

Kohler

Kohler K-4108BR Bedienungsanleitung

Kohler

Kohler K-4350 Series Montageanleitung

Kohler

Kohler TROCADERO K-2247-1 Bedienungsanleitung

Kohler

Kohler K-2829 Bedienungsanleitung

Kohler

Kohler Purist K-T97328-4-BN Bedienungsanleitung

Kohler

Kohler K-72777 Montageanleitung

Kohler

Kohler Mira Agile S Eco Bedienungsanleitung

Kohler

Kohler K-R99252X-4CD Montageanleitung

Kohler

Kohler Fluence K-702221-6L Bedienungsanleitung

Kohler

Kohler Mira Jump 7.5 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung