Kramer SL-1N Bedienungsanleitung

SL-1N Quick Start

P/N:

2900- 301273QS

Rev:

Scan for full manual

SL-1N Quick Start Guide

This guide helps you install and use your SL-1N for the first time.

Go to www.kramerav.com/downloads/SL-1N to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

SL-1N Master Room Controller

1 Power supply (12V DC)

4 Rubber feet

Kramer RC-IR3 Infrared Remote Control Transmitter with

batteries and user manual

1 Quick start guide

Step 2: Get to know your SL-1N

Feature

Function

RELAYS Terminal Blocks

Connect to low-voltage relay-driven devices (from 1 to 3)

IR Output Terminal Blocks

Connect to IR emitter cables (from 1 to 2)

RS-232 Terminal Blocks

Connect to the RS-232 devices (from 1 to 2)

ETHERNET RJ-45 Connector

Connects to the PC or other serial controller through computer networking

LAN

DEFAULT Pushbutton

Press to reset to factory default definitions:

IP number −192.168.1.39, mask –255.255.0.0, gateway –0.0.0.0, also to

remove the current configuration

First disconnect the power cord and then connect it again while pressing the

ETH Factory Reset button. The unit powers up and loads its memory with the

factory default definitions and erases all stored presets

K-NET Terminal Block

PIN GND is for the ground connection; PIN B (-) and PIN A (+) are for

RS-485, and PIN +12V is for powering the unit

The ground connection is sometimes connected to the shield of the RS-485

cable

12V DC Connector

For supplying power to the unit

IR IN Sensor and LED

Accepts IR remote commands

IR INPUT 3.5mm Mini Jack

Connects to a remote infrared sensor

NET LED

Illuminates while transmitting over Ethernet

K-NET LED

Illuminates when the K-NET is active (red –transmit, green –receive, during

normal activity flashes red)

RS-232 Tx/Rx LEDs

Illuminates while transmitting/receiving on an RS-232 port (1 to 2) (red –

transmit, green –receive)

IR LEDs

Illuminates when an IR port is active

RELAYS LEDs

Illuminates when a relay is active (1 to 3)

SRVC DIP-Switch

Slides down for service use only, slides up for normal operation

K-NET TERM DIP-Switch

Slides down for K-NET termination, slides up for not terminated

PROGRAM USB Connector

Connect to a computer for unit configuration and firmware upgrading

Step 3: Mount SL-1N

Install SL-1N using one of the following methods:

•Attach the rubber feet and place the unit on a flat surface.

•Fasten a bracket on each side of the unit and attach it to a flat surface

(see www.kramerav.com/downloads/SL-1N).

•Mount the unit in a rack using the recommended rack adapter

(see www.kramerav.com/product/SL-1N).

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your SL-1N.

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/SL-1N.

Using third-party cables may cause damage!

Step 5: Connect power

Connect the power cord to SL-1N and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the

terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

Step 6: Operate SL-1N

Operate via the RC keypad, IR remote control, K-NET or Ethernet

Andere Handbücher für SL-1N

Dieses Handbuch passt für folgende Modelle

Andere Kramer Controller Handbücher

Kramer

Kramer 860 Bedienungsanleitung

Kramer

Kramer SL-12 Bedienungsanleitung

Kramer

Kramer FC-22ETH Bedienungsanleitung

Kramer

Kramer PT-12 Bedienungsanleitung

Kramer

Kramer SL-240 Bedienungsanleitung

Kramer

Kramer FC-26LA Bedienungsanleitung

Kramer

Kramer RC-7B Bedienungsanleitung

Kramer

Kramer RC-7B Bedienungsanleitung

Kramer

Kramer K-NET RC-53D Bedienungsanleitung

Kramer

Kramer RC-62 Bedienungsanleitung

Kramer

Kramer SL-10 Bedienungsanleitung

Kramer

Kramer RC-2C Bedienungsanleitung

Kramer

Kramer RC-63DLN Bedienungsanleitung

Kramer

Kramer RC-74DL Bedienungsanleitung

Kramer

Kramer RC-7LC Bedienungsanleitung

Kramer

Kramer VA-4H Bedienungsanleitung

Kramer

Kramer RC-43SL Bedienungsanleitung

Kramer

Kramer SL-1 Bedienungsanleitung

Kramer

Kramer KT-107-INWL Bedienungsanleitung

Kramer

Kramer RC-6 Bedienungsanleitung

Kramer

Kramer RC-8RKL Bedienungsanleitung

Kramer

Kramer SL-280 Bedienungsanleitung

Kramer

Kramer SL-240C Bedienungsanleitung

Kramer

Kramer RC-52N Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch