Kramer VS-62DT Bedienungsanleitung

VS-62DT Quick Start (P/N: 2900-300665QS REV 1)

P/N:

2900- 300665QS

Rev:

Scan for full manual

VS-62DT Quick Start Guide

This guide helps you install and use your VS-62DT for the first time.

Go to www.kramerav.com/downloads/VS-62DT to download the latestuser manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VS-62DT 6x2 UHD Matrix Switcher

4 Rubber feet

IRremote control transmitter with batteries

1 Power supply (48V DC)

1 Quick start guide

Step 2: Get to know your VS-62DT

Feature

Function

IR Sensor & LED

Signal receiver for the infrared remote control transmitter. LED lights yellow

ON LED

Lights when the unit ispowered on

INPUT SELECTOR TO OUT 1 (1to 6)

Press one of the six inputs to switch it to Output1

SWAP Button

Press to swap output 1 and output 2 (analog audio only)

EDID Button

Press to capture the EDID

VOL+ Button

Press to increase the analog audio volume on output 1

VOL- Button

Press to decrease the analog audio volume on output 1

MUTE Button

Press to toggle muting of output 1 analog audio

POE STATUS LED

Lights when transmitting power over Ethernet to anotherdevice

PROG mini USB connector

Used for upgrading the firmware

INPUT SELECTOR TO OUT 2 (1 to 6)

Press one of the six inputs to switch it to Output 2

LOCK Button

Press and hold to toggle locking and unlocking the front panel buttons

PATTERN Button

Press to activate the test pattern generator. When the generator is active, press

one of the input buttons to select a test pattern

VOL+ Button

Press to increase the analog audio volume on output 2

VOL- Button

Press to decrease the analog audio volume on output 2

MUTE Button

Press to toggle muting of output 2 analog audio

LINK LED

Lights when there is activity on the HDBaseTconnection

Feature

Function

REMOTE INPUT TO OUT 1 TB

Connects to external contact closure input switches

REMOTE INPUT TO OUT 2 TB

Connects to external contact closure input switches

RS-232 TB

Connects to a local RS-232 source

AUDIO OUT 1 TB

Connects to a balanced stereo audio acceptor

AUDIO OUT 2 TB

Connects to a balanced stereo audio acceptor

SETUP DIP-Switches

Sets the device configuration (see Step 7)

ETHERNET RJ-45 connector

Connects to a network for control

RESET Button

Press while power-cycling the device to reset to factorydefault parameters

48V DC Connector

Connects to a power supply for the unit

INPUT 1to 6HDMI Connectors

Connect to up to 6 HDMI sources

HDBT OUT 1 RJ-45 Connector

Connects to an HDBaseT TP line

OUT 2 HDMI Connector

Connects to an HDMI acceptor

Step 3: Install the VS-62DT

Attach the rubber feet and place on a table or mount the VS-62DT in a rack (using an optional RK-1 rack mount).

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-62DT. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the VS-62DT.

Connect the audio output:

To a balanced stereo audio

acceptor:

To a unbalanced stereo

audio acceptor:

Step 5: Connect the power

Connect the 48V DC power adapter to the VS-62DT and plug it into the mains electricity.

Step 6: Acquiring an EDID

To copy the EDID from an Output to one or more

Inputs:

1. Press the EDID button to enter the EDID setting mode.

The EDID button lights.

2. From the To OUT 1 (top) row, press each of the Inputs

to which you want to copy the EDID from Output 1.

Each selected Input LED lights.

3. From the To OUT 2 (bottom) row, press each of the

Inputs into which you want to copy the EDID from

Output 2.

Each selected Input LED lights.

4. Press the EDID button.

The button no longer lights and the EDID changes are

saved.

To copy the default EDID to one or more Inputs:

1. Press the EDID button to enter the EDID setting mode.

The EDID button lights.

2. For each Input to which you want to copy the default

EDID, press both the To OUT 1 and To OUT 2 buttons

simultaneously.

Both top row and bottom row Input LEDs light.

3. Press the EDID button.

The button no longer lights and the EDID changes are

saved.

Step 7: Set the DIP-switches

Use the DIP-switches to set the device configuration

Feature

Description

HDCP support on inputs

On (down)—Disable HDCP support on all inputs

Off (up)—Enable HDCP support which is defined by P3000 commands

Video mode switching

Output 1

On (down)—Auto

Off (up)—Manual

Last connected/Priority

mode Output 1

When DIP-switch 2 is set to Auto (ON):

On (down)—Enable Last Connected mode

Off (up)—Enable Priority mode where the priority of each input is defined

bythe input number, (1 is the highest priority)

Video mode switching

Output 2

On (down)—Auto

Off—Manual

Last connected/Priority

mode Output 2

When DIP-switch 4 is set to Auto (ON):

On (down)—Enable Last-connected mode

Off (up)—Enable Priority mode where the priority of each input is defined

bythe input number, (1 is the highest priority)

N/A

Step 8: Operate via the front panel buttons and via the:

IR remote controller

Web pages:

RS-232 and Ethernet:

Default RS-232

Parameters

Baud Rate:

115,200 (9600)

Parity:

None

Data Bits:

Command Format:

ASCII

Stop Bits:

Example (Route the video from the

HDMI3 input to the HDMI OUT2

port):

#ROUTE 1,2,3<cr>

TCP/IP Parameters

IP Address:

192.168.1.39

Default UDP Port #:

50000

Subnet mask:

255.255.255.000

Maximum combined

TCP and UDP Ports:

Default

gateway:

192.168.1.254

Step 9: Control peripheral devices via IR remote control:

You can use a remote control transmitter (that is used for controlling a peripheral device, for example, a DVD player) to send

commands (to the A/V equipment) from/to any of the transmitters /receivers connected to the HDBT connectors.

Andere Handbücher für VS-62DT

Inhaltsverzeichnis

Andere Kramer Matrix-Umschalter Handbücher

Kramer

Kramer XL 3216V Bedienungsanleitung

Kramer

Kramer VP-778 Bedienungsanleitung

Kramer

Kramer VS-6YC Bedienungsanleitung

Kramer

Kramer VS-88FO Bedienungsanleitung

Kramer

Kramer VS-62DT Bedienungsanleitung

Kramer

Kramer Sierra Video 1616V5S Bedienungsanleitung

Kramer

Kramer VS-42UHD Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1204V5S Bedienungsanleitung

Kramer

Kramer Sierra Video 6448V5Sxl Bedienungsanleitung

Kramer

Kramer VP-4x8 Bedienungsanleitung

Kramer

Kramer 3232HDS Bedienungsanleitung

Kramer

Kramer 88V3 Bedienungsanleitung

Kramer

Kramer VS-2516 Bedienungsanleitung

Kramer

Kramer VS-3232DN Bedienungsanleitung

Kramer

Kramer VS-62H Bedienungsanleitung

Kramer

Kramer 1608HD Bedienungsanleitung

Kramer

Kramer VS-3232V Bedienungsanleitung

Kramer

Kramer VS-401YC Bedienungsanleitung

Kramer

Kramer VS-2616 Bedienungsanleitung

Kramer

Kramer VS-88DT Bedienungsanleitung

Kramer

Kramer 1616D Bedienungsanleitung

Kramer

Kramer VP-4x4xl Bedienungsanleitung

Kramer

Kramer VS-88A Bedienungsanleitung

Kramer

Kramer MTX3-16-M Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Shinybow USA

Shinybow USA SB-8811 Bedienungsanleitung

Optimus

Optimus Compact Bedienungsanleitung