KWIK GOAL 2B1901 Bedienungsanleitung

NZ429 Rev. 10/07/19

NOTE: Components may be packaged in one or more additional boxes.

ASSEMBLY INSTRUCTIONS FOR 2B1901 BFR-1 REBOUNDER

2. Read through entire instruction before beginning assembly and installation.

1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,

notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or

damp packaging may damage contents.

Parts

Left Base (1)

(Part# UZ1656)

86”

Right Base (1)

(Part# UZ1657)

Rear Base (1)

(Part# UZ1658)

85-3/8”

86”

Post (3)

(Part# WZ968)

Upper Adjustment Tube (2)

(Part# UZ1653)

76-3/4”

Lower adjustment Tube (2)

(Part# UZ1654)

75”

Crossbar (1)

(Part# UZ1655)

86”

***CAUTION***

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

Any modifications to this or any Kwik Goal product will void any and all warranties.

Sticker

140 Pacific Drive Quakertown, PA 18951

800-531-4252 Kwikgoal.com

2019 Kwik Goal Ltd. ©

IMPORTANT SAFETY INSTRUCTIONS

3. BFR-1 rebounder must be on flat, level ground when in use.

4. Never allow anyone to climb on netting or framework.

READ CAREFULLY

1. Perform routine inspections on all fasteners and components to ensure that they are

secure and in good condition. Kwik Goal recommends routine inspections on a

monthly basis, as well as before and after each use.

5. Use a minimum of two people to move BFR-1. Understand, and follow all

steps of moving rebounder as outlined in assembly instructions.

2. Check cable assembly on each front corner as part of monthly and before / after use

inspections. Replace worn, damaged, or missing hardware and cables. Be sure

fasteners are tightened properly. If immediate repairs cannot be made, remove

rebounder from use and store in a secure area.

WARNING

Cable Assembly

Two Places

NZ429 Rev. 10/07/19

140 Pacific Drive Quakertown, PA 18951

800-531-4252 Kwikgoal.com

2019 Kwik Goal Ltd. ©

Channel Spacer (See Frame Hdw)

(Part# UZ812)

Net (1)

(Part# 3B807)

(Part# 10B3101 Pack of 100)

Net Clip (60)

Crossbar Corner (4)

(Part# UZ1418)

Left Corner (1)

(Part# UZ1651) (Part# UZ1652)

Right Corner (1) Threaded Channel Spacer

(See Wheel Hdw)

(Part# UZ691)

(Part# UZ1649)

Adjustment Tube Connector (4)

(Part# UZ1648)

Base Connector (2) Mounting Bracket (2)

(Part# UZ659)

Parts (continued)

Stop Plate (2)

(Part# UZ1254)

Tire and Wheel Assembly (2)

(Part# VZ349)

NZ429 Rev. 10/07/19

Plastic

Metal

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

***CAUTION***

Any modifications to this or any Kwik Goal product will void any and all warranties.

9/16

1/2”, 9/16”, 3/4” & 15/16”

Wrenches

Scissors

5/16” Flat Washer (Part# TZ4) (12)

3/8“ x 1-3/4” Hex Bolt (Part# TZ227) (2)

3/8” Flat Washer (Part# TZ60) (14)

3/8” Square Nut (Part# TZ247) (10)

3/8“ Flat Washer (Part# TZ60) (24)

Frame Hdw (Part# JZ259)

Hardware

3/8“ Lock Nut Thin (Part# TZ370) (2)

before beginning assembly.

Channel Spacer (Plastic) (Part# UZ812) (12)

5/8“ Lock Nut (Part# TZ294) (2)

Connector Hdw (Part# JZ260)

1/2“ Lock Nut (Part# TZ28) (2)

5/16” x 3-1/4” Hex Bolt (Part# TZ206) (4)

5/16” x 1/4” Plastic Spcr (Part# TZ418) (4)

3/8“ Lock Washer (Part# TZ65) (4)

5/8“ x 3-1/2” Hex Bolt (Part# TZ369) (2)

Wheel Hdw (Part# JZ226)

3/8“ x 3/4” Soc Cap Scrw (Part# TZ208) (2)

3/8“ x 1” Hex Bolt (Part# TZ1) (4)

5/8“ Jam Nut (Part# TZ108) (2)

3/8“ Flat Washer (Part# TZ60) (4)

in one or more boxes. Open all packages

1/2“ Flat Washer (Part# TZ297) (2)

Anti-seize (Part# VZ327) (2)

Note: Hardware may be packaged separately

Large Nylon Washer (Part# TZ204) (2)

3/8“ Lock Washer (Part# TZ65) (24)

Threaded Channel Spacer (Metal) (Part# UZ691) (2)

3/8“ x 1-3/4” Hex Bolt (Part# TZ227) (24)

1/4” Tooth Lock Washer (Part# TZ129) (2)

1/4” x 3/4” Pan Hd Screw (Part# TZ376) (2)

5/16” x 5-1/4” Hex Bolt (Part# TZ416) (2)

5/16” Lock Nut (Part# TZ5) (6)

3/8“ x 7/8” Hex Bolt (Part# TZ249) (12)

3/8” Lock Washer (Part# TZ65) (14)

Handle (Part#VZ679) (1)

Cable Assembly (Part#VZ871) (2)

Ratchet with

1/2”, 9/16”, 3/4” & 15/16”

Sockets

Parts (continued)

Assembly Tools

5/16” Hex

Wrench

Cable Assembly

(See Connector Hdw)

(Part# VZ871)

Handle

(See Connector Hdw)

(Part# VZ679)

Bungee (120)

(Part# 10B3501 Pack of 30)

NZ429 Rev. 10/07/19

Phillips Screwdriver

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

***CAUTION***

Any modifications to this or any Kwik Goal product will void any and all warranties.

Tape Measure

3. Hardware for this step is in the Wheel Hdw pack

Assemble left and right wheel assemblies.

NZ429 Rev. 10/07/19

1/2" Lock Nut

1/2" Flat Washer

Mounting

Bracket

5/8" X 3 1/2"

Hex Bolt

5/8" Jam Nut

Stop Plate

5/8" Lock Nut

3/8" X 3/4" Socket Head Capscrew

3/8" Lock Nut

Tire and Wheel

Assembly

Stop Plate

Tighten nut snug,

then loosen until

Mounting Bracket can

rotate on Stop Plate.

Left Side Wheels

1/2" Lock Nut

1/2" Flat Washer

Mounting

Bracket

5/8" X 3 1/2"

Hex Bolt

5/8" Jam Nut

Stop Plate

Right Side Wheels

5/8" Lock Nut

3/8" X 3/4" Socket Head Capscrew

3/8" Lock Nut

Tire and Wheel

Assembly

Stop Plate

Tighten nut snug,

then loosen until

Mounting Bracket can

rotate on Stop Plate

Mounting

Bracket

Mounting

Bracket

Large Nylon Washer

Apply two small (1/4” max) drops of

anti-seize to each side of washer.

Keep anti-seize close to center hole.

Large Nylon Washer

Apply two small (1/4” max) drops of

anti-seize to each side of washer.

Keep anti-seize close to center hole.

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

***CAUTION***

Any modifications to this or any Kwik Goal product will void any and all warranties.

Assemble posts, crossbar, crossbar corners and post corners as shown. Be sure sticker on crossbar is oriented

correctly. Press joints together firmly before tightening bolts.

Note: Square nuts will float loose in channel until used later.

4. Hardware for steps 4 through 6 are in the Frame Hdw and Connector Hdw packs

Post

Crossbar Corner

Crossbar

Post

Left Corner

Right Corner

Post

Channel Spacer

(Plastic)

3/8" Flat Washer

3/8" Lock Washer

3/8" x 1-3/4" Hex Bolt

3/8” Square Nut

Post

Crossbar Corner Crossbar

3/8” Square Nut (2)

3/8" x 1-3/4" Hex Bolt

3/8" Lock Washer

3/8" Flat Washer

Post

NZ429 Rev. 10/07/19

Channel Spacer

(Plastic)

Crossbar Corner

Crossbar

3/8” Square Nut (2)

3/8" x 1-3/4" Hex Bolt

3/8" Lock Washer

3/8" Flat Washer

Post

Channel Spacer

(plastic)

Left Corner

Post

3/8" Flat Washer

3/8" Lock Washer

3/8" x 1-3/4" Hex Bolt

3/8” Square Nut

Channel Spacer

(Plastic)

***CAUTION***

Any modifications to this or any Kwik Goal product will void any and all warranties.

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

Top of sticker

this side

5. Attach adjustment tube and base connectors to assembled frame at locations shown.

Post

Crossbar Corner

Crossbar

30”

Post Base Connector

Base Connector

Adjustment Tube Connector

Left Corner

Right Corner

Post

Adjustment Tube Connector

Crossbar

3/8” Flat Washer

3/8” Lock Washer

3/8” x 7/8” Hex Bolt

3/8” Square Nuts

NZ429 Rev. 10/07/19

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

Any modifications to this or any Kwik Goal product will void any and all warranties.

***CAUTION***

Base Connector

Right Corner

3/8” Flat Washer

3/8” Lock Washer

3/8” x 7/8” Hex Bolt

3/8” Square Nut

3/8” x 1-3/4” Hex Bolt

Base Connector

Left Corner

3/8” Flat Washer

3/8” Lock Washer

3/8” x 1-3/4” Hex Bolt

3/8” Square Nut

3/8” x 7/8” Hex Bolt

6. Hardware for steps 6 through 10 are in the Frame Hdw, Wheel Hdw, and Connector Hdw packs.

Note: Square nuts will float loose in channel until used later.

Assemble bases and crossbar corners. Press joints together firmly before tightening bolts.

Left Base

Right Base

Rear Base

Crossbar Corner

NZ429 Rev. 10/07/19

3/8" x 1-3/4" Hex Bolt

3/8" Lock Washer

3/8" Flat Washer

3/8" Square Nut

Channel Spacer

(Plastic)

3/8" x 7/8" Hex Bolt

3/8" Lock Washer

3/8" Flat Washer

Cable Assembly

3/8" x 1-3/4" Hex Bolt

3/8" Lock Washer

3/8" Flat Washer

Channel Spacer

(Plastic)

3/8" Square Nut

Threaded inserts

towards outside

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

Any modifications to this or any Kwik Goal product will void any and all warranties.

***CAUTION***

NZ429 Rev. 10/07/19

7. Attach adjustment tube connector and handle to assembled base at locations shown.

30”

Handle

Adjustment Tube Connector

Rear Base

3/8” Flat Washer

3/8” Lock Washer

3/8” x 7/8” Hex Bolt

3/8” Square Nuts

1/4" x 3/4" Pan Hd Screw

1/4” Internal Tooth Lock Washer

Handle

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

***CAUTION***

Any modifications to this or any Kwik Goal product will void any and all warranties.

Left Base

Right Base

NZ429 Rev. 10/07/19

Left Base

Right Base

Rear Base

Post

Crossbar

8. Attach post / crossbar assembly to base assembly and insert threaded channel spacer (metal) into base. Tighten

lock nut until one to two threads protrude out of the top of the nut.

Sports equipment not in use must be disassembled and stored in a safe, secure place. Assembled sports

equipment should not be left unattended. Sports equipment should be checked for safety on a regular basis.

***CAUTION***

Any modifications to this or any Kwik Goal product will void any and all warranties.

5/16” x 5-1/4” Hex Bolt

5/16”Flat Washer

5/16”Lock Nut

Insert Threaded Channel

Spacer (Metal)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KWIK GOAL Sport & Outdoor Handbücher

KWIK GOAL

KWIK GOAL KWIK FLEX 2B1505 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B4006 Bedienungsanleitung

KWIK GOAL

KWIK GOAL WC-ASK Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B2201 Bedienungsanleitung

KWIK GOAL

KWIK GOAL FUSION 2B3806 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B3003 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 7E201 Bedienungsanleitung

KWIK GOAL

KWIK GOAL KWIK FLEX 2B1502 Bedienungsanleitung

KWIK GOAL

KWIK GOAL KWIK TOM 16B3901 Bedienungsanleitung

KWIK GOAL

KWIK GOAL FUSION 2B3806SW Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B5004 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B2 Bedienungsanleitung

KWIK GOAL

KWIK GOAL FUSION GOAL 2B3806 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2P201 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B4003 Bedienungsanleitung

KWIK GOAL

KWIK GOAL ACADEMY GOAL 2B5006 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B6001 Bedienungsanleitung

KWIK GOAL

KWIK GOAL FUSION 120 GOAL Bedienungsanleitung

KWIK GOAL

KWIK GOAL Academy GOAL 2B5002 Bedienungsanleitung

KWIK GOAL

KWIK GOAL WC-240 Bedienungsanleitung

KWIK GOAL

KWIK GOAL FUSION 25B386512 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B3024 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 16B6 Bedienungsanleitung

KWIK GOAL

KWIK GOAL 2B4005 Bedienungsanleitung

Beliebte Sport & Outdoor Handbücher anderer Marken

Flybar

Flybar POGO TRICK BOARD Bedienungsanleitung

Crivit

Crivit 93713 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 90865 Bedienungsanleitung

Hudora

Hudora 76171 Montageanleitung

Axler

Axler GSU-1 Bedienungsanleitung

Aquaglide

Aquaglide FREEFALL 6 LANDING PAD Bedienungsanleitung

Cap Strength

Cap Strength POWER RACK FM-CS7000F Bedienungsanleitung

La Sportiva

La Sportiva RACE BORG Bedienungsanleitung

Crivit

Crivit 302640 Bedienungsanleitung

Sportime

Sportime Equalizer Bedienungsanleitung

T&R Sports

T&R Sports 5FT FOOSBALL TABLE Bedienungsanleitung

Salewa

Salewa VERT Bedienungsanleitung

KICK

KICK Decagon Bedienungsanleitung

byox

byox FJ-4.5FT Bedienungsanleitung

CHINESPORT Spa

CHINESPORT Spa 01325 Bedienungsanleitung

AXI.COM

AXI.COM ConesPro101 Bedienungsanleitung

Insportline

Insportline IN 2052 Bedienungsanleitung

Rugged Interactive

Rugged Interactive CardioWall Compact Kurzanleitung