KWIK GOAL PRO PREMIER 2B9006 Bedienungsanleitung

ASSEMBLY INSTRUCTIONS FOR 2B9006 & 2B9006SW PRO PREMIER COPA GOAL

NOTE: Components may be packaged in one or more additional boxes.

2. Read through entire instruction before beginning assembly and installation.

1. Unpack all parts and check for damage that may have occurred during shipping. If damage has

occurred, notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging

immediately. Wet or damp packaging may damage contents.

140 Pacific Drive Quakertown, PA 18951

(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869

Visit our website @ kwikgoal.com

2016, Rev. 2019 Kwik Goal Ltd.

Right Post (1)

(Part# UZ649)

Left Post (1)

(Part# UZ1527)

Parts

NZ391 Rev. 07/15/19

***CAUTION***

This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES

and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings

must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use

must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal

Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use

this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.

All warning and safety labels included with this product must be visible at all times.

Any modifications to this or any Kwik Goal product will void any and all warranties.

280”

Crossbar (2)

(Part# UZ393)

280”

Back Bottom Bar (1)

(Part# UZ966) 100-3/8” 100-3/8”

140 Pacific Drive Quakertown, PA 18951

(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869

Visit our website @ kwikgoal.com

1998 rev 2009 Kwik Goal Ltd.

2. Safety/Warning labels must be clearly visible.

IMPORTANT GOAL SAFETY INSTRUCTIONS

READ CAREFULLY

1. Check for structural integrity and proper connecting hardware before every

use. Replace damaged or missing parts or fasteners immediately.

3. Securely anchor moveable soccer goals at ALL times.

4. Always instruct players, managers, coaches, trainers, teachers, maintenance

workers and all other personnel who might come in contact with the goal,

on the safe handling of and potential dangers associated with moveable

soccer goals.

5. Always exercise extreme caution when moving goals and provide adequate

manpower to move goals of varied sizes and weights. Moveable soccer goals

should only be moved by authorized personnel.

6. NEVER allow anyone to climb on the net or goal framework.

7. Moveable soccer goals should only be used on LEVEL fields, NEVER on a

slope or hill area.

8. Remove nets when goals are not in use.

9. Most of the tip-over injuries occurred when goals were unattended. Anchor

or chain one goal to another or to nearby fence posts, dugouts, or any other

similar sturdy fixture when not in use. If this is not practical, store moveable

soccer goals in a place where children cannot have access to them.

10. Fully disassemble goals for seasonal storage.

NZ391 Rev. 07/15/19

Chain (4)

w/ Snap Link & Anchor Plate

(Part# UZ846 )

Back Pole Brace (2)

(Part# UZ1526)

Back Pole Brace (2)

(Part# UZ1525)

Post Brace (2)

(Part# UZ737)

Anchor Bag (6)

(Part# 10B1605)

Ground Anchor (4)

w/hardware

(Part# 10B101 Set of 4)

***CAUTION***

This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES

and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings

must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use

must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal

Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use

this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.

All warning and safety labels included with this product must be visible at all times.

Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19

Back Pole (2)

(Part# UZ1524)

Net (1)

(Part# 3B1502)

Red Dot Blue Dot

Back Bottom Bar

Connector (2)

(Part# UZ1033)

Back Pole Cap (2)

(Part # VZ719)

Tamper Resistant

Net Clip (100)

(Part# 10B3401 Pack of 100)

Net Clip Driver (1)

(Part# VZ140)

Left Base (1)

(Part# UZ1520)

100-3/8”

Right Base (1)

(Part# UZ1521)

100-3/8”

Channel Spacer (8)

(Part# UZ812)

Bolt Cap (4)

(Part# VZ751)

Net Rope

Assembly (2)

(Part# JZ215 Pack of 2

w/ Snaplink)

Any modifications to this or any Kwik Goal product will void any and all warranties.

***CAUTION***

This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES

and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings

must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use

must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal

Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use

this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.

All warning and safety labels included with this product must be visible at all times.

NZ391 Rev. 07/15/19

7/16” Lock Nut (Part# TZ47) (4)

Hardware

Note: Hardware may be packaged separately

in one or more boxes. Open all packages

before beginning assembly.

7/16” X 6” Hex Bolt (Part# TZ380) (4)

7/16” Flat Washer (Part# TZ171) (8)

3/8“ x 1-3/4” Hex Bolt (Part# TZ227) (16)

3/8" x 7/8" Hex Bolt (Part# TZ249) (18)

3/8” x 5/8” Hex Bolt (Part# TZ383) (4)

5/16" X 1” Hex Bolt (Part# TZ121) (8)

5/16" Flat Washer (Part# TZ269) (8)

3/8“ Lock Washer (Part# TZ65) (36)

3/8“ Flat Washer (Part# TZ60) (40)

3/8" Square Nut (Part# TZ247) (22)

5/16" Lock Washer (Part# TZ122) (8)

1/4" X 2” Eye Bolt (Part# TZ381) (2)

1/4" Lock Nut (Part# TZ19) (2)

1/4"Flat Washer (Part# TZ361) (2)

Ratchet with

7/16” ,1/2”, 5/8”,

9/16” & 3/4”

Sockets

9/16

7/16”, 1/2”, 5/8”,

9/16” & 3/4”

Wrenches

Rubber Mallet

Assembly Tools

Knob w/o Threads (4)

(Part# VZ687)

280”

Pole Rope

Assembly (4)

(Part# JZ222 Pack of 4)

112”

4. Insert one square nut in each of the assembled posts.

3. Attach left post and right post to crossbar using channel spacers and 3/8” hex bolts. Note direction of decals

before fastening. Be sure connections are pressed firmly together before tightening hex bolts.

Left Post

Right Post

Crossbar

Decals

3/8” Square Nut

3/8” X 1-3/4” Hex Bolt

Channel Spacer

3/8” Flat Washer

Right Post

3/8” Lock Washer

Crossbar

Any modifications to this or any Kwik Goal product will void any and all warranties.

***CAUTION***

This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES

and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings

must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use

must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal

Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use

this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.

All warning and safety labels included with this product must be visible at all times.

NZ391 Rev. 07/15/19

5. Attach base to crossbar and bottom back bar as shown.

Note direction of decals before fastening. Assemble all

hardware first, then go back and tighten each bolt. Be

sure connections are pressed firmly together before

tightening hex bolts.

6. Using a rubber mallet, install bolt caps on exposed threads of

7/16” X 6” hex bolts.