La Crosse Technology WS-7215U-IT Bedienungsanleitung

WS-7215U-IT

Wireless 915 MHz

Radio-controlled Temperature Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 3

Quick Set-Up Guide 4

Detailed Set-Up Guide

Battery installation 5

Program Mode

Program Sequence and Default Settings 6

Function Keys 6

Setting the LCD Contrast 7

Setting the Time Zone 7-8

Daylight Saving Time Setting 8

Radio-controlled Time Setting 9

12/24-hour Time Setting 9

Setting the Time 10-11

Setting the Year, Day and Month 11

Setting the Snooze 12

Setting the Temperature Format 12

Setting the forecast sensitivity

Features

Indoor Temperature and Humidity 13

Outdoor Temperatures 13

Minimum & Maximum Records (Indoor,

Outdoor, & Resetting) 14-15

Additional Remote Control Sending Units (Set-Up,

Viewing, & Operation) 15-16

Mounting 17-18

Troubleshooting 19-20

Maintenance & Care 20

Specifications 21

Warranty Information 22-23

INVENTORY OF CONTENTS

1. The Wireless Temperature Station (Figure 1).

2. One remote temperature sensor with mounting bracket (Figure 2).

3. Three each, ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1. Two fresh AA 1.5V batteries for the Wireless Temperature Station.

Figure 1

Time LCD

Date LCD

Indoor LCD

Outdoor LCD

Figure 2

Mounting

Bracket TX29U-IT remote

temperature sensor

INSTANT TRANSMISSION is the state-

of-the-art new wireless transmission

technology, exclusively designed and

developed by LA CROSSE

TECHNOLOGY. INSTANT

TRANSMISSION offers you an

immediate update (every 4 seconds!) of

all your outdoor data measured from

the sensors: follow your climatic

variations in real-time!

This product offers:

2. Two fresh AA 1.5V batteries for the remote temperature sensor.

3. One, Philips screwdriver for mounting.

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency Division)

WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time and date

signal continuously throughout the United States at 60 kHz. The signal can be received up to

2,000 miles away through the internal antenna in the Wireless Temperature Station.

However, due to the nature of the Earth’s Ionosphere, reception is very limited during

daylight hours. The temperature station will search for a signal every night when reception is

best. The WWVB radio station derives its signal from the NIST Atomic clock in Boulder,

Colorado. A team of atomic physicists is continually measuring every second, of every day,

to an accuracy of ten billionths of a second per day. These physicists have created an

international standard, measuring a second as 9,192,631,770 vibrations of a Cesium-133 atom

in a vacuum. For more information on the atomic clock and WWVB please see the NIST

website at http://www.boulder.nist.gov/timefreq/stations/wwvb.htm.

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the Wireless Temperature Station and remote temperature sensor 3 to 5

feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then into the

Wireless Temperature Station.

(All remote temperature sensors must be started before the Wireless

Temperature Station)

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the Wireless Temperature Station and remote temperature sensor will

start to talk to each other and the display will show both the indoor temperature and

an outdoor temperature. If the Wireless Temperature Station does not display both

temperatures after the 15 minutes please retry the set up as stated above. After both

indoor and outdoor temperatures are displayed for 15 minutes you can place your

remote temperature sensor outdoors and set your time.

The remote temperature sensor should be placed in a dry, shaded area. The

temperature sensor has a range of 330 feet. Keep in mind that the 330 feet is in open

air with no obstructions and that radio waves DO NOT curve around objects. Actual

transmission range will vary depending on what is in the path of the signal. Each

obstruction (roof, walls, floors, ceilings, thick trees, etc.) will effectively cut signal

range in half.

Example: A Wireless Temperature Station with a 330 feet range is mounted on an

interior wall, so that the signal has to pass through one interior wall, one exterior

wall, and across the 10 feet width of the room between the 2 walls. The first wall

will reduce the range to 165 feet, and the second wall will reduce the range to 87

feet. Factoring in the 10 foot room, this leaves a maximum of 77 feet of remaining

signal range.

This allowance is typically enough for a frame wall with non-metallic siding;

however certain materials can reduce range even further. Metal siding, stucco, and

some types of glass can reduce signal range by as much as ¾ or more, compared to

the ½ reduction typical of most obstructions. It is possible to receive a signal

through these materials, however maximum range will be much less due to their

tendency to absorb or reflect a much larger portion of the sensor’s signal.

To complete the set up of your Wireless Temperature Station after the 15 minutes

have passed please follow the steps that follow in the Detailed Set-Up Guide.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION (When one temperature sensor is being

used)

1. First, insert the batteries to the temperature sensor (see “A. Remote

Temperature sensor” below).

2. Within 30 seconds of powering up the sensor, insert the batteries to the

Temperature Station (see “B. Wireless Temperature Station” below). Once

the batteries are in place, all segments of the LCD will light up briefly.

Following the indoor temperature and humidity, and the time as 12:00 will

be displayed. If they are not shown in LCD after 60 seconds, remove the

batteries and wait for at least 60 seconds before reinserting them. Once the

indoor data is displayed user may proceed to the next step.

3. After the batteries are inserted, the Temperature Station will start receiving

data signal from the sensor. The outdoor temperature should then be

displayed on the Temperature Station. If this does not happen after 2

minutes, the batteries will need to be removed from both units and reset

from step 1 and the signal reception icon is no longer shown.

A. REMOTE TEMPERATURE SENSOR

1. Remove the mounting bracket. The

bracket snaps on and off easily.

2. Remove the battery cover, by sliding the

cover down.

3. Observing the correct polarity install 2 AA

batteries. The batteries will fit tightly (to

avoid start-up problems make sure they do

not spring free).

4. Replace the battery cover by sliding upwards. Be sure battery

cover is on securely.

B. WIRELESS TEMPERATURE STATION

1. Remove the battery cover. To do this, insert a solid object in

the space provided at the lower-central position of the battery

cover, then push up and pull out on the battery cover.

2. Observe the correct polarity, and install 2 AA batteries.

3. Replace the battery cover.

*When the signal is successfully received by the Wireless Temperature

Station, the icon will be switched on. (If not successful, the icon will not be

shown in LCD) So the user can easily see whether the last reception was

Battery

Cover

Battery

cover

Sensor signal

reception icon*

successful (icon on) or not (icon off). On the other hand, the short blinking

of the icon shows that a reception is being done now.

•

If the signal reception is not successful on the first frequency (915MHz) for

45 seconds, the frequency is changed to 920MHz and the learning is tried

another 45 seconds. If still not successful the reception is tried for 45 seconds

on 910MHz. This will also be done for re-synchronization.

PROGRAM MODE

Programming Note: If 30 seconds is allowed to pass, or the CH button is

pressed during the programming mode, the unit will confirm/set the last

information entered—the display will stop flashing and return to normal

time-date readings. If you don’t leave the program mode during the

programming of sections III through XII, you can advance to step 4 of the

next program setting. If you do leave the program setting (or want to

program a specific setting) follow each instructional step to program that

setting.

I. PROGRAMMING SEQUENCE AND DEFAULT SETTINGS

The programming sequence and default (factory) settings are as

follows:

LCD Contrast 5

Time Zone -5 (Eastern)

Daylight Saving Time 1 (on)

Radio-controlled time reception ON

12/24-hour time 12

Time 12:00

Year 2006

Day and Month 1.1.

Snooze (this function not used) 10

Temperature Format °F

Setting the forecast sensitivity (this function not used)

Please note that while there is a snooze adjustment in the programming this

is an unused function as there is no alarm on the indoor temperature station.

II. FUNCTION KEYS

The function keys are located on the front of the unit directly below the

LCD.

III. SETTING THE LCD CONTRAST

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

Note: There are 8 LCD contrast levels to choose from—“Lcd 0” is

the lightest, and “Lcd 7” is the darkest.

3. Press and release the IN button to select the level you desire.

4. Press and release the SET button to confirm and advance to

the Time Zone setting.

IV. TIME ZONE SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting

will flash.

3. Press and release the SET button again.

4. The time zone will flash in the date LCD.

5. Press and release the IN button to select your time zone.

Note: When a time zone for the U.S. is selected the corresponding

abbreviation will appear above the time (please see the table on the

next page). It is possible to select any time zone from –12 GMT to

+12 GMT (for example to see the time in another country)

TIME ZONES

GMT 0

ALT Atlantic -4

EST Eastern -5

CST Central -6

MST Mountain -7

PST Pacific -8

ALA Alaska -9

HAW Hawaii -10

6. Press and release the SET button to confirm and advance to

the Daylight Saving Time setting.

V. DAYLIGHT SAVING TIME (DST) SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

3. Press and release the SET button twice.

4. “DST” will appear in the date LCD and either “1” or “0” will

flash.

5. Press and release the IN button to select DST on or off.

“DST 0” indicates that the feature is off and the WWVB will not

change times automatically. “DST 1” indicates that the feature is

on and the WWVB will change times automatically.

Note: Some locations (Arizona and parts of Indiana) do not

follow Daylight Saving Time, and should select “DST 0.”

6. Press and release the SET button to confirm and advance to

the radio-controlled time on/off setting.

VI. RADIO-CONTROLLED TIME ON/OFF SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

3. Press and release the SET button three times.

4. “RCC” will appear in the date LCD and “ON” or “OFF” will

flash in the time LCD.

5. Press and release the IN button to select radio-controlled time

on or off.

6. Press and release the SET button to confirm and advance to

the 12/24-hour time setting.

VII. 12 OR 24 HOUR TIME SETTING

1. Press and hold the SET button for 5 seconds.

2. “LCD” will show in the time LCD and the number setting will

flash.

3. Press and release the SET button four times.

4. “12h” or “24h” will flash in the time LCD.

5. Press and release the IN button to select 12 or 24-hour time

format.

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology CA74962 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Weather Direct WD-3308 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9077U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology The Weather Channel WS-9005TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6821A Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-805 Installationsanleitung

La Crosse Technology

La Crosse Technology WS-1517 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 302-604B Abmessungen

La Crosse Technology

La Crosse Technology WS-9032U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7013U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1412-3TX Abmessungen

La Crosse Technology

La Crosse Technology WS-9037U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6282 Installations- und Betriebshandbuch

La Crosse Technology

La Crosse Technology 308-1415BWV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1710 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C85845 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 061317 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C84428 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-145 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C79790 Abmessungen

La Crosse Technology

La Crosse Technology WS-7013BZ Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7136U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-3502 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-3104U Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung