La Crosse Technology WS-8015U Bedienungsanleitung

WS-8015U

Wireless 433 MHz

Weather Station with Sun/Moon Time

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents/ Additional Equipment 3

Quick Set Up Guide 4

About WWVB 4

Detailed Set Up Guide 5-6

Battery Installation 5

Start Up Sequence 6

Explanation of LCD Information 7

Function Key Layout 7

Program Mode 8-13

Time, 12/24 Hour Mode and Date Setting 8

City Location Setting 8-9

U.S. City Codes 9-11

Canada City Codes 12

Mexico City Codes 12

Time Zone Setting 12

Daylight Saving Time (DST) Setting

Weather Measuring Units 12-13

LCD Contrast 13

Overview of Programming Sequence 13

Features and Operation 14-20

Sun Rise/Set and Moon Rise/Set Calculation 14-15

Moon Phase 15

MINIMUM/MAXIMUM TEMPERATURE/HUMIDITY 15-16

MULTIPLE REMOTE SENSORS 16

REMOTE TEMPERATURE ALARM 16-17

COMFORT INDICATOR 17

WEATHER FORECAST ICON AND PRESSURE TREND 17-18

WEATHER TENDENCY ARROWS 18

STORM WARNING ALARM 19

TWO HOUR AIR PRESSURE TENDENCY CHART 19

BAROMETRIC AIR PRESSURE READING 19

AIR PRESSURE HISTORY BAR CHART 19-20

MOUNTING 21

MAINTENANCE AND CARE 23

TROUBLESHOOTING GUIDE 23

SPECIFICATIONS 24

WARRANTY INFORMATION 25

INVENTORY OF CONTENTS

1. WS-8015U—indoor weather station

2. TX4U—remote thermo/hygro

(temperature/humidity) sensor

3. Instruction manual and warranty card

ADDITIONAL EQUIPMENT (not included)

1. Five fresh AA 1.5V alkaline batteries.

2. One wall-mounting screw (optional)

ABOUT WWVB (radio-controlled time)

The NIST (National Institute of Standards and Technology—Time and

Frequency Division) radio station, WWVB, is located in Ft. Collins, Colorado

and transmits the exact time signal continuously throughout the United States at

60 kHz. The signal can be received up to 2,000 miles away through the internal

antenna in the indoor weather station. However, due to the nature of the Earth’s

Ionosphere, reception is very limited during daylight hours. The indoor weather

station will search for a signal every night when reception is best. The WWVB

radio station derives its signal from the NIST Atomic clock in Boulder,

Colorado. A team of atomic physicists continually measure every second of

every day to an accuracy of ten billionths of a second a day. These physicists

have created an international standard, measuring a second as 9,192,631,770

vibrations of a Cesium 133 atom in a vacuum. For more information about

WWVB please see the NIST website at

http://www.boulder.nist.gov/timefreq/stations/wwvb.htm

Figure 1.

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor weather station and remote thermo/hygro sensor 3

to 5 apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote thermo/hygro sensor first then

into the indoor weather station.

(All remote thermo/hygro sensors must be started before the indoor

weather station)

4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.

In this time the indoor weather station and remote thermo/hygro sensor will start

to talk to each other and the indoor weather station will show both the indoor

temperature and humidity and the outdoor temperature and humidity. If the

indoor weather station does not display all values after the 10 minutes please

retry the set up as stated above. After all values are displayed for 10 minutes

you can place your remote thermo/hygro sensor outdoors and set your time.

The remote thermo/hygro sensor should be placed in a dry, shaded area. The

remote thermo/hygro sensor has a range of 80 feet. Any walls that the signal

will have to pass through will reduce distance. An outdoor wall or window will

have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of

resistance. Your distance plus resistance should not exceed 80 ft. in a straight

line.

NOTE: Fog and mist will not harm your remote thermo/hygro sensor but direct

rain must be avoided.

To complete the set up of your indoor weather station after the 10

minutes have passed please follow the steps in the Detailed Set Up

Guide.

Note: The remote thermo/hygro sensor transmits a signal every 3 minutes; after

the batteries have been installed, the indoor weather station will search for the

signal for a duration of 5 minutes. If there is no temperature reading in the

OUTDOOR LCD after 5 minutes, make sure the units are within range of each

other, or repeat the battery installation procedure.

DETAILED SET-UP GUIDE

I. Battery Installation

Batteries will fit tightly. To avoid start-up problems, make sure that the

batteries do not spring free. Also be sure to insert alkaline batteries into the

remote thermo/hygro sensor first, then the indoor weather station. Initial set

up should be done with the remote thermo/hygro sensor and indoor weather

station in the same room. The units should be permanently mounted only

after the signal reception has been verified.

A. Remote Temperature and Humidity Sensor, TX4U

1. Pull the cylindrical rain cover off the sensor.

2. Remove the battery cover (located on the backside of the sensor,

above the mounting post and bracket). Press the arrow and slide

the battery cover off.

3. Observing the correct polarity install 2 Alkaline AA batteries.

4. Replace battery cover, and place rain cover snugly onto the sensor.

B. Weather Center

1. Remove the battery cover (the cover has white writing on it).

2. Observe the correct polarity, and

install three Alkaline AA batteries.

3. Do not press any buttons for at least

ten minutes. If a button is pressed

before the Weather Center has

received information from the

TX4U sensor, no data will be

received from that sensor until reset.

4. Replace the battery cover.

Battery

Cover

Mounting

Bracket/Recept

Rain

Cover

Thermo-Hygro

Sensor

II. Start Up Sequence

A. Initial Start

1. Immediately after the batteries have been installed, the indoor

weather station will sound a “beep”, and the LCD will completely

light up for a brief moment.

2. All information will then appear in normal mode, with “12:00” as

the default time and “1.1” as the default date (2001 as the year).

3. “DCA” is the default city (Washington, DC, USA), with the

sunrise, sunset, moonrise and moonset times displayed for that city

at that date.

4. The indoor temperature and humidity, and barometric air pressure

(as 29.91 inHg relative RH) will also be displayed.

5. There is a “satellite” icon that appears near the bottom of the LCD,

to the right of the “max” remote temperature—this icon informs

the user that the indoor weather station is looking for signals from

the remote thermo/hygro sensor. Within five minutes the remote

temperature and humidity should be displayed—if not, remove

batteries from all units and repeat battery installation, the remote

temperature sensor first, then the indoor weather station.

B. WWVB Reception

1. Once the batteries are installed in the Weather Center, it will

automatically search for the WWVB signal. If it receives a good

signal (which is unlikely during daylight hours in most locations),

the WWVB reception indicator (looks like a tower icon) will flash.

The indoor weather station requires five full minutes of good

reception to successfully capture the signal and set to the correct

hour, minute, second, month, day and year. If the signal reception

is not successful within ten minutes, the signal search will be

cancelled and will automatically resume every two hours until the

signal is successfully captured.

2. The signal is sent from Ft. Collins, Colorado only and is similar to

an AM radio signal. Atmospheric interferences such as storms,

sunspots, and even sunlight will cause the signal to not travel as

far.

3. To maximize reception, place the indoor weather station in a

window facing Colorado, at least six feet from any electrical

source (computers, televisions, refrigerators, etc.). Do not move

the indoor weather station while it is searching for the signal.

4. The time and date can be manually set. Once the signal is captured,

it will override any time and date set to the time zone selected.

5. Once the time and date are set, the indoor weather station will

conduct a search every night at midnight and correct to the

accurate time and date (Daylight Saving Time is automatic). If the

signal has been received in the past 24 hours, the reception

indicator will be displayed.

III. Explanation of LCD Information

A. The below picture highlights the LCD features

B. There are many different modes the indoor weather station can be set

to. The LCD shown is the normal operating mode, and your actual data

shown will be different based on your local settings and conditions.

IV. Function Key Layout

A. The below picture shows the eight function keys used in programming

and operation of your indoor weather station

V. Program Mode

The program mode is laid out in a manner that allows you to program each

function separately, or you can follow the instructions entirely to program the

indoor weather center. Complete programming is usually done for the initial

set-up, and will require you to skip step 1 and 2 of each programming section.

The programming mode can be exited at any time by either pressing the “CH”

button, or waiting for the 16-second time-out to take effect.

A. Overview of programming mode sequence

Note: If the country setting is other than USA step 8 is city, step 9 is time

zone, etc.

1. Hour 2. Minute 3. 12/24 hour 4. Year

5. Month 6. Date 7. Country 8. State

9. City 10. Time Zone 11. DST on/off 12. °F/°C

13. inHg/hPa 14. Relative

pressure setting 15. Forecast

sensitivity 16. Storm

warning setting

17. Storm

alarm on/off 18. LCD

contrast 19. LI on/off

B. Time, 12/24 Hour Mode and Date Setting

The WWVB signal will override any manual set time and date information. The

time will be based on the time zone selected.

1. Press and hold the “SET” button for 1 second.

2. The hour is now flashing.

3. Press and release the “+” or “–“ button to select the current hour.

Note: In 12h mode “PM” will appear to the left of the time during PM hours.

If the time is not within the PM hours nothing will be displayed. Be sure to set

the time to the correct AM/PM time to ensure automatic reception.

4. Press the “SET” button to advance to the minute

5. The minute is now flashing.

6. Press and release the “+”or “–“ button to select the current

minute.

7. Press and release the “SET” button to advance to the 12/24-hour

setting.

8. “12” is now flashing.

9. Press and release the “+”or “–“ button to select either 12 (am/pm)

or 24 hour (military) time format.

10. Press and release the “SET” button to advance to the year setting.

11. The year is now flashing.

12. Press and release the “+”or “–“ button to select the current year.

13. Press and release the “SET” button to advance to the month

setting.

14. The month is now flashing.

15. Press and release the “+”or “–“ button to select the current

month.

16. Press and release the “SET” button to advance to the date setting.

17. The date is now flashing.

18. Press and release the “+”or “–“ button to select the current date.

19. Press and release the “SET” button to advance to the location

setting (skip steps 1 and 2 in section B if continuing).

C. City Location Setting

The list of the cities available is listed after this section.

1. Press and hold the “SET” button for 1 second.

2. Press and release the “SET” button 6 times.

3. The country location will flash (USA default/factory setting).

4. Press and release the “+”or “–“ button to select the country

(USA=United States, CAN=Canada, MEX=Mexico).

5. Press and release the “SET” button to advance to the state setting

(USA only) or the city location (Canada or Mexico).

Skip to step nine if Mexico or Canada is selected

6. The state is now flashing.

7. Press and release the “+”or “–“ button to select the state.

8. Press and release the “SET” button to advance to the city setting.

9. The city is now flashing.

10. Press and release the “+”or “–“ button to select the city closest to

your location (abbreviated by airport code, if applicable).

11. Press and release the “SET” button to advance to the time zone

setting (skip steps 1 and 2 in section D if continuing).

Section C lists the available city codes. Section D continues with the

setup programming.

Andere Handbücher für WS-8015U

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9066U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WW85777v2 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 308-1415BW Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9018U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1517 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7025TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology KCombo3 WS-9080U-IT WS-9640U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1416v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 328-10618 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Outdoor Sensor Handbuch

La Crosse Technology

La Crosse Technology S88785 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7049U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7042 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1414M Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-3102U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1451v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308A-146 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WW85777 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 308-1415FCTv2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7047U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 9245 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7390U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9006U Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung