Lantronix MatchPort b/g Pro Kurzanleitung zur Einrichtung

Part Number 900-532

Revision B December 2011

MatchPort b/g Pro

Integration Guide

MatchPort b/g Pro Integration Guide 2

transmitted or reproduced in any form or by any means without the written permission of

Lantronix. Printed in the United States of America.

MatchPort®, with its patent-pending technology, is a trademark of Lantronix. Ethernet is a

trademark of XEROX Corporation. UNIX is a registered trademark of The Open Group.

Windows is a trademark of Microsoft Corp.

Contacts Lantronix Corporate Headquarters

167 Technology Drive

Irvine, CA 92618, USA

Phone: 949-453-3990

Fax: 949-450-7249

Technical Support

Online: www.lantronix.com/support

Email/Chat: www.lantronix.com/support

Sales Offices

For a current list of our domestic and international sales offices go to the Lantronix web

site at www.lantronix.com/about/contact/.

Disclaimer and Revisions

Operation of this equipment in a residential area is likely to cause interference to other

devices, in which case the user, at his or her own expense, will be required to take

whatever measures may be required to correct the interference.

Note: This product has been designed to comply with the limits for a Class B

digital device pursuant to Part 15 of FCC and EN55022:1998 Rules when

properly enclosed and grounded. These limits are designed to provide

reasonable protection against radio interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and if not

installed and used in accordance with this guide, may cause interference to radio

communications.

Changes or modifications to this device not explicitly approved by Lantronix will void the

user's authority to operate this device.

Note: With the purchase of MatchPort b/g Pro, the OEM agrees to an OEM

firmware license agreement that grants the OEM a non-exclusive, royalty-free

firmware license to use and distribute the binary firmware image provided, only to

the extent necessary to use the MatchPort b/g Pro hardware. For further details,

please see the MatchPort b/g Pro OEM firmware license agreement.

Disclaimer This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

MatchPort b/g Pro Integration Guide 3

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This device is intended only for OEM Integrators. The OEM integrator should be aware of

the following important issues.

Labeling of the End Product

The label on the end product incorporating the MatchPort b/g pro module must clearly

state that it contains an FCC-approved RF module. For example, "This product contains

an RF transmitter FCC ID: R68MPBGPRO and IC: 3867A-MPBGPRO."

RSS-GEN Sections 7.1.4 and 7.1.5 Statement for Devices with Detachable Antennas

This device has been designed to operate with the antennas listed in the Certificate, and

having a maximum gain of 5 dBi. Antennas not included in this list or having a gain

greater than 5 dBi are strictly prohibited for use with this device, unless system-level FCC

approval is gained. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (EIRP) is not more

than that required for successful communication.

Integration Note

a) This module is authorized under limited module approval specified to mobile host

equipment. So, the antenna must be installed such that 20cm is maintained between the

antenna and users.

b) The transmitter module may not be co-located with any other transmitter or antenna.

As long as the two conditions above are met, further transmitter testing will not be

required. However, the OEM integrator is still responsible for testing their end product for

any additional compliance requirements required with this module installed (for example,

digital device emission, PC peripheral requirements, etc.)

Note: In the event that these conditions cannot be met (for example certain

laptop configurations, general purpose PCMCIA or similar cards, or co-location

with another transmitter), then the FCC authorization is no longer considered

valid and the FCC ID cannot be used on the final product (including the

transmitter) and obtaining a separate FCC authorization.

Note: Changes or modifications to this device not explicitly approved by Lantronix will

void the user's authority to operate this device.

Revision Table

Date

Rev.

Comments

April 2008

Initial Release

December 2011 B Updated absolute maximum ratings and recommended

supply voltage information.

MatchPort b/g Pro Integration Guide 4

Contents

Contents ______________________________________________________________ 4

List of Figures __________________________________________________________ 5

List of Tables___________________________________________________________ 5

1: Introduction 6

About the Integration Guide _______________________________________________ 6

Additional Documentation_________________________________________________ 6

2: Description and Specifications 7

MatchPort b/g Pro Block Diagram___________________________________________ 7

MatchPort b/g Pro Pinouts_____________________________________________________9

Power and Ground ______________________________________________________ 9

Reset________________________________________________________________ 10

Ethernet Connections ___________________________________________________ 10

Ethernet LED Connections _______________________________________________ 11

Wireless LED Connections _______________________________________________ 11

Antenna Mating Connector _______________________________________________ 11

Antenna______________________________________________________________ 12

Serial Input/Output _____________________________________________________ 13

Sample Layouts for RS485 Connectivity ____________________________________ 13

IO Configurable Pins (CPs)_______________________________________________ 15

BOOTP_EN#__________________________________________________________ 16

BOOTP enable ____________________________________________________________16

Diagnostics LED ___________________________________________________________16

Pin Connection Options______________________________________________________16

Electrical Specifications _________________________________________________ 17

Wireless Specifications__________________________________________________ 18

Technical Specifications _________________________________________________ 18

Dimensions ___________________________________________________________ 19

Recommended PCB Layout ______________________________________________ 21

Product Information Label________________________________________________ 22

3: Demonstration Kit 23

Contents of the Kit______________________________________________________ 23

Demo Board Description_________________________________________________ 23

Serial Interfaces _______________________________________________________ 24

Power Supply _________________________________________________________ 24

General Control________________________________________________________ 24

Configuration Switch Bank _______________________________________________ 25

Demo Board Layout ____________________________________________________ 27

Demo Board Schematics ________________________________________________ 28

A: Compliance 32

B: Warranty 33

MatchPort b/g Pro Integration Guide 5

List of Figures

Figure 2-1. MatchPort b/g Pro Block Diagram_____________________________________ 8

Figure 2-2. Connection Diagram to an RJ45 Jack ________________________________ 10

Figure 2-3. Recommended LED Connections____________________________________ 11

Figure 2-4. Recommended LED Connections____________________________________ 11

Figure 2-5. Reverse-SMA to U.FL (P/N 500-180-R) _______________________________ 12

Figure 2-6. U.FL to U.FL Cable (P/N 500-181-R) _________________________________ 12

Figure 2-7. R-SMA Antenna Connector Dimensions (not to scale)____________________ 12

Figure 2-8. Combined RS232/422 Transceiver___________________________________ 13

Figure 2-9. Separate RS232/422 Transceivers___________________________________ 14

Figure 2-10. Separate RS422 Transceivers for 2-Wire and 4-Wire Setups _____________ 15

Figure 2-11. BOOTP_EN# APPLICATION CIRCUIT ______________________________ 17

Figure 2-12. Side Views ____________________________________________________ 19

Figure 2-13. Top View ______________________________________________________ 20

Figure 2-14. Bottom View ___________________________________________________ 20

Figure 2-15. PCB Layout (Top View) __________________________________________ 21

Figure 2-16. Product Label __________________________________________________ 22

Figure 3-1. MatchPort Demo Board Layout______________________________________ 27

Figure 3-2. Demo Board Block Diagram ________________________________________ 28

Figure 3-3. Schematic ______________________________________________________ 29

List of Tables

Table 2-1. RS232 Connections _______________________________________________ 13

Table 2-2. JP6 RS422/485 Connections on Demo board___________________________ 13

Table 2-3. Absolute Maximum Ratings _________________________________________ 17

Table 2-4. Recommended Operating Conditions _________________________________ 17

Table 2-5. Wireless Specifications ____________________________________________ 18

Table 2-6. Specifications ____________________________________________________ 18

Table 3-1. RS-232 Signals on Serial Port 1 _____________________________________ 24

Table 3-2. RS-422 4-Wire Connector on Serial Port 1 _____________________________ 24

Table 3-3. Demo Board JP1 Jumper Configuration _______________________________ 25

Table 3-4. Demo Board JP7 Jumper Configuration for CON1 _______________________ 25

Table 3-5. Demo Board JP8 Jumper Configuration for CON2 _______________________ 25

Table 3-6. Demo Board JP8 Jumper Configuration for CON2 _______________________ 25

Table 3-7. Demo Board JP5 Jumper Configuration _______________________________ 26

Table 3-8. Demo Board Configurable Pin Jumper Configurations ____________________ 26

MatchPort b/g Pro Integration Guide 6

1: Introduction

About the Integration Guide

This guide provides the information needed to integrate the MatchPort b/g Pro™ device

server within another product. The intended audiences are the engineers responsible for

integrating the MatchPort b/g Pro into their product.

Additional Documentation

The following guides are available on the product CD and the Lantronix Web site

(www.lantronix.com)

MatchPort b/g Pro User

Guide Provides information needed to configure, use,

and update the MatchPort b/g Pro firmware.

MatchPort b/g Pro

Command Reference Lists and explains MatchPort b/g Pro command

line and XML commands.

MatchPort

Demonstration Kit Quick

Start Guide

Provides information needed to configure, use,

and update the MatchPort demonstration kit.

MatchPort b/g Pro Integration Guide 7

2: Description and Specifications

The MatchPort b/g Pro embedded device server is a complete network-enabling solution

on a 1.75"x1.75" PCB. This miniature device server empowers original equipment

manufacturers (OEMs) to go to market quickly and easily with networking and web page

serving capabilities built into their products.

The MatchPort b/g Pro has the following features:

Power Supply: Single regulated 3.3V input required. On board step down

conversion. LC filtering to minimize noises and emissions on all supply lines.

Controller: A Lantronix DSTni-FX 32-bit microprocessor, running at 166 MHz

internal bus and 83 MHz external bus.

Memory: 64 Mbits Flash and 64 Mbits SDRAM.

Wireless LAN: 802.11bg compliant radio with U.FL connector for external

antenna. 802.11i and 802.1X security standards supported.

Ethernet: 10/100 Base TX with auto-negotiation and HP auto-MDIX. On- board

100-ohm terminations included. External RJ45 jack and 1:1 Ethernet magnetics

with a minimal numbers of discrete components required.

Network interface status indication: On board WLAN and Ethernet LED

drivers.

Serial Ports: Two full duplex serial ports with hardware flow control and modem

control handshaking signals. Standard or customized baud rates up to 230 Kbps.

External level shifters for RS232. Port 1 can also be configured to drive RS422 or

RS485 level shifters.

Configurable IO Pins (CPs): Up to 7 pins are configurable as general purpose

I/Os.

Interface Signals: 3.3V-level interface signals.

Temperature Range: Operates over an extended temperature range.

MatchPort b/g Pro Block Diagram

The following drawing is a block diagram of the MatchPort b/g Pro showing the

relationships of the components.

2: Description and Specifications

MatchPort b/g Pro Integration Guide 8

Figure 2-1. MatchPort b/g Pro Block Diagram

2: Description and Specifications

MatchPort b/g Pro Integration Guide 9

MatchPort b/g Pro Pinouts

There are two headers of 1x20, 2-mm pin spacing. The odd row header is designated as P1; pins

are numbered 1 to 39. The even row header is designated as P2; pins are numbered

2 to 40.

PIN #

NAME

Dir

Active level

FUNCTION

P1.1

RESETIN#

Low

Reset. Leave floating if not used.

P1.3

RSTTODFLT

Low

Reset to Defaults

P1.5

TX1

Transmit Data, port 1

P1.7

RTS1

Request to Send, port 1

P1.9

RX1

Receive Data, port 1

P1.11

CTS1

Clear to Send, port 1

P1.13

CP1

IO Configurable Pin 1

P1.15

CP2

IO Configurable Pin 2

P1.17

CP3

IO Configurable Pin 3

P1.19

CP4

IO Configurable Pin 4

P1.21

TX2

Transmit Data, port 2

P1.23

RTS2

Request to Send, port 2

P1.25

RX2

Receive Data input , port 2

P1.27

CTS2

Clear to Send input , port 2

P1.29

CP5

IO Configurable Pin 5

P1.31

CP6

IO Configurable Pin 6

P1.33

CP7

IO Configurable Pin 7

P1.35

RSVD

Reserved. Do not connect

P1.37

S3.3V

3.3V Power Input

P1.39

GND

Ground

PIN #

NAME

Dir

Active level

FUNCTION

P2.2

GND

Ground

P2.4

RSVD

Reserved. Do not connect

P2.6

ETX+

PHY’s Differential Ethernet Transmit Data +

P2.8

ETX-

PHY’s Differential Ethernet Transmit Data -

P2.10

ETCT

Differential Ethernet Transmit Data Center Tap

P2.12

ERCT

Differential Ethernet Receive Data Center Tap

P2.14

ERX+

PHY’s Differential Ethernet Receive Data +

P2.16

ERX-

PHY’s Differential Ethernet Receive Data -

P2.18

E_LINKLED

Low

Ethernet Link LED.

P2.20

E_ACTLED

Low

Ethernet Activity LED.

P2.22

W_LINKLED

Low

Wireless LAN Link/Activity LED. Active low

P2.24

BOOTP_EN#

Low

Network Boot and Boot Loader Enable.

P2.26

RSVD

Reserved. Do not connect

P2.28

RSVD

Reserved. Do not connect

P2.30

RSVD

Reserved. Do not connect

P2.32

RSVD

Reserved. Do not connect

P2.34

RSVD

Reserved. Do not connect

P2.36

RSVD

Reserved. Do not connect

P2.38

RSVD

Reserved. Do not connect

P2.40

RSVD

Reserved. Do not connect

Power and Ground

The MatchPort b/g Pro requires a regulated 3.3Vdc +/- 5% power input at P1.37 and

ground at pin P1.39.

2: Description and Specifications

MatchPort b/g Pro Integration Guide 10

Note: To minimize noises as well as voltage drops at the connection, We recommend

direct connection of 3.3V and ground on the MatchPort b/g Pro to 3.3V power and ground

planes of the target board in place of heavy trace routing.

Reset

The MatchPort b/g Pro reset pin RESETIN# is an input-only pin and connects to an 811-

type reset IC. This input is for a pushbutton switch type manual reset. If no external reset

control is desired, leave this pin floating.

Minimum reset pulse is 2 ms.

There is an on board capacitor, 0.1uF to ground, at the RESETIN# to filter out transient

voltages. However, it is a good practice to have RESETIN# trace on the target board as

short as possible to avoid reset occurrences when transient voltages such as those

caused by ESD are present.

Ethernet Connections

The MatchPort b/g Pro provides Ethernet interface transmit ETX and receive data ERX

connections from a PHY device. Thus, before presenting signals to the outside world

using an RJ45 jack, a 1:1 Ethernet Magnetics is needed to interface and to isolate the

unit. A recommended connection diagram to an RJ45 jack with integrated 1:1 Ethernet

magnetics is shown below.

Figure 2-2. Connection Diagram to an RJ45 Jack

We recommend a low capacitance TVS diode array such as a Semtech SRV05-4 at

ETX+, ETX-, ERX+, ERX- if frequent transient voltages are present.

Andere Handbücher für MatchPort b/g Pro

Inhaltsverzeichnis

Andere Lantronix Server Handbücher

Lantronix

Lantronix SLB Bedienungsanleitung

Lantronix

Lantronix XPort Bedienungsanleitung

Lantronix

Lantronix ETS Bedienungsanleitung

Lantronix

Lantronix EDS32PR Bedienungsanleitung

Lantronix

Lantronix XPort Direct Kurzanleitung zur Einrichtung

Lantronix

Lantronix CoBox-Micro Bedienungsanleitung

Lantronix

Lantronix xPico XPW100A003-01-B Kurzanleitung zur Einrichtung

Lantronix

Lantronix EDS1100 Installationshandbuch

Lantronix

Lantronix xDirect Bedienungsanleitung

Lantronix

Lantronix Console Server 800 Bedienungsanleitung

Lantronix

Lantronix MatchPort b/g Kurzanleitung zur Einrichtung

Lantronix

Lantronix xDirect Bedienungsanleitung

Lantronix

Lantronix EDS8PS Bedienungsanleitung

Lantronix

Lantronix WiBox Bedienungsanleitung

Lantronix

Lantronix MSS Bedienungsanleitung

Lantronix

Lantronix XPress DR+ Bedienungsanleitung

Lantronix

Lantronix EDS-MD EDS-MD4 Installationshandbuch

Lantronix

Lantronix PremierWave XN Bedienungsanleitung

Lantronix

Lantronix XPico 900-691-R Bedienungsanleitung

Lantronix

Lantronix SCSxx05 Bedienungsanleitung

Lantronix

Lantronix MSS4-D Bedienungsanleitung

Lantronix

Lantronix Com Port Redirector Bedienungsanleitung

Lantronix

Lantronix UDS200 Bedienungsanleitung

Lantronix

Lantronix SecureBox SDS2100 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung