Lippert LUVERNE 401720 Bedienungsanleitung

LUVERNETRUCK.COM •PRODUCT SUPPORT: 877.287.8634 •401720-INS-RA •02/22/2022 •ECN9236 •PAGE 1

Product Registration and Warranty

LUVERNE stands behind our products with industry-leading warranties. To get copies of the product

warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys

INSTALLATION MANUAL 401720

Parts List

Qty Description

2Mounting bracket

2AC mounting bracket

2AC top mounting bracket

2U-bolt, 3-3/4"

12 Lock washer, 5/16"

8Thread-cutting bolt, 5/16"

14 Washer, 5/16"

8Flange nut, M8

8Hex bolt, M8

8Clip nut, M8

4Spacer

4Bolt retainer

Tools Required

Socket, 1/2" Ratchet

Wrench, 1/2" Drill

Flathead screwdriver Drill bit, 3/8"

Marker Drill bit, 3/32"

Putty knife Drill bit, 19/64"

Maintenance

Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive

cleaners, abrasive pads, wire brushes or other similar products that may damage the ﬁnish.

Product Photo

Front

Rear

Torque Speciﬁcations

M8 bolt 20 ft-lbs.

5/16" bolt 20 ft-lbs.

Use above torque setting unless otherwise noted

Level of Difficulty

Easy

Installation difficulty levels are based on time

and effort involved and may vary depending on

the installer level of expertise, condition of the

vehicle and proper tools and equipment.

This is the first of two manuals

required to complete this installation.

The second manual is included with

your side bars / running boards.

NOTICE

Visit www.luvernetruck.com for a full-color copy of this

instruction manual, as well as helpful videos, guides and much more!

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

Periodic inspection of your product should be performed

to ensure all hardware and / or components remain secure.

To help prevent damage to the product or vehicle, refer to the specified

torque specifications when securing hardware during the installation process.

LUVERNETRUCK.COM •PRODUCT SUPPORT: 877.287.8634 •401720-INS-RA •02/22/2022 •ECN9236 •PAGE 2

Step 1B - Vans without factory studs

Starting on the driver side, locate

the front bracket mounting location.

(See figure 2 on the last page of the manual).

From the underside of the plastic

rocker molding, use a flathead screwdriver

to release the bottom push pins.

NOTICE

Plastic trim clips are single use only.

DO NOT REMOVE. Only release

the bottom push pins. Use a putty

knife to lightly pry the trim away

from the rocker panel if clearance is needed.

Locate the mounting location for the

first bracket and mark the locations for

each mouning hole. Using a 3/32" drill bit,

drill a pilot hole in each of the marked spots.

Enlarge with a 3/8" drill bit.

Slide two M8 clip nuts over the lower set of

holes in the pinch weld and insert the 3.75"

U-bolt through the upper set of drilled holes.

Secure the U-bolt with the bolt retainers and

slide two black spacers on the U-bolt followed

by the mounting bracket. Secure the bracket

with two M8 nuts on the studs and two 5/16"

lock washers and two M8 bolts in the clip nuts.

Snug the hardware,

but do not fully tighten.

Step 1

Note: For vans without

factory studs skip to Step 1B.

Starting on the driver side, locate

the front bracket mounting location.

For vans with factory studs, slide a 1/4" spacer

on each of the studs. Place the front bracket

on the studs and secure with two M8 flange

nuts on the studs and two 5/16" thread cutting

bolts into the factory holes on the bottom of the

rocker panel.

LUVERNETRUCK.COM •PRODUCT SUPPORT: 877.287.8634 •401720-INS-RA •02/22/2022 •ECN9236 •PAGE 3

Step 3

Hold the assembled AC bracket along the pinch

seam and mark each of the four hole locations.

Step 2

Assemble the rear AC bracket using two

M8 bolts, two 5/16" washers and two M8 nuts.

On the driver side, locate the

second bracket mounting location.

(See figure 2 on the last page of the manual).

Step 4

Using a 3/32" drill bit, drill a pilot hole in each

of the marked spots. Enlarge the two upper

holes with a 19/64" drill bit and the

two bottom holes with a 3/8" drill bit.

NOTICE

The upper two holes will use self-threading

bolts. Do not oversize these holes.

Step 5

Slide two clip nuts over the bottom drilled holes.

Secure the AC bracket to the bottom two holes

using two M8 bolts and two 5/16" lock washers.

Secure the AC bracket to the two

upper holes using two 5/16" thread-cutting

bolts and two 5/16" lock washers.

Tighten all hardware.

LUVERNETRUCK.COM •PRODUCT SUPPORT: 877.287.8634 •401720-INS-RA •02/22/2022 •ECN9236 •PAGE 4

Step 6

Repeat Steps 1 through 5 on the passenger side of the vehicle.

Tighten all hardware.

Note: To complete the installation, refer to the

manual included with your running boards / side steps.

8-3/4"

42-1/2"

Figure 1

Passenger side shown

Figure 2

Driver side shown

Andere Lippert Autozubehör Handbücher

Lippert

Lippert Stargazer Spirit XTR Skylight Bedienungsanleitung

Lippert

Lippert 10570 Gebrauchsanweisung

Lippert

Lippert Level-up Bedienungsanleitung

Lippert

Lippert Project 2000 Sliding Step Bedienungsanleitung

Lippert

Lippert VELA POP-UP ROOF Bedienungsanleitung

Lippert

Lippert FLYSCREEN N Series Bedienungsanleitung

Lippert

Lippert Ground Control 3.0 Bedienungsanleitung

Lippert

Lippert Power Steps 2.0 Bedienungsanleitung

Lippert

Lippert Curt 18415 Bedienungsanleitung

Lippert

Lippert Vela Pop Up Gebrauchs- und Pflegehandbuch

Lippert

Lippert Stargazer Nano Wide Skylight Bedienungsanleitung

Lippert

Lippert THEATER SEATING Gebrauchs- und Pflegehandbuch

Lippert

Lippert Promaster Bedienungsanleitung

Lippert

Lippert Tire Linc Montageanleitung

Lippert

Lippert Vela Bedienungsanleitung

Lippert

Lippert Power Step 2.0 Bedienungsanleitung

Lippert

Lippert LatchXtend RV Door Handle Bedienungsanleitung

Lippert

Lippert TI-276 Bedienungsanleitung

Lippert

Lippert Curt 16613 Bedienungsanleitung

Lippert

Lippert CURT 45937 Bedienungsanleitung

Lippert

Lippert SolidStep 4.0 Bedienungsanleitung

Lippert

Lippert SolidStep Gen 2 Montageanleitung

Lippert

Lippert Thin Shade 806621 Montageanleitung

Lippert

Lippert SMART BED UNIVERSAL KIT Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung