Lippert Project 2000 Sliding Step Bedienungsanleitung
Project 2000 Sliding Step
OWNER'S MANUAL
Rev: 02.08.22 Page 2 CCD-0004560
TABLE OF CONTENTS
Introduction 2
Safety 3
Operation 4
Wiring Diagram 5
Diagram 1 5
For Automatic Opening/Closing Kit 6
Maintenance 8
Troubleshooting 8
Emergency Operation 8
Resources Required 8
Notes 9
Introduction
The Project 2000 Sliding Step is a resistant to corrosion, lightweight, and has a thermal breaker in case of
high strain. The foot board is constructed of anodized aluminum with anti-slip rubber.
Disassembly of the Project 2000 Sliding Step voids the warranty. Contact Lippert to obtain replacement parts.
Additional information about this product can be obtained from lci1.com/support or by downloading the
free LippertNOW app. The app is available on Apple App Store® for iPhone® and iPad® and also on Google
Play™ for Android™ users.
iPhone®, and iPad® are registered trademarks of Apple Inc.
Google Play™ and Android™ are trademarks of Google Inc.
For information on the assembly or individual components of this product, please visit:
https://support.lci1.com/steps/
NOTE: Images used in this document are for reference only when assembling, installing and/or operating
this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Rev: 02.08.22 Page 3 CCD-0004560
The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause
death or serious personal injury if not performed safely and within the parameters set forth in this
manual.
Failure to follow instructions provided in this manual may result in death, serious personal injury
and/or severe product and property damage, including voiding of the component warranty.
Always wear eye protection when performing service, maintenance or installation procedures.
Other safety equipment to consider would be hearing protection, gloves and possibly a full face
shield, depending on the nature of the task.
The “CAUTION” symbol above is a sign that a safety risk is involved and may cause personal injury
and/or product or property damage if not safely adhered to and within the parameters set forth
in this manual.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions,
i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This
manual cannot begin to plot out instructions for every possibility, but provides the general instructions,
as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the
provided instructions may result in death, serious personal injury, severe product and/or property damage,
including voiding of the LCI limited warranty.
Do not step on a retracted step. Stepping on a retracted step can cause personal injury and/or
severely damage the motor. Extend the step to safely use the product as intended.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Rev: 02.08.22 Page 4 CCD-0004560
Operation
Do not walk on the step until it is completely stopped. Do not interfere with the step while in
operation. Doing so may cause serious personal injury.
Make sure that children are away from the electric step when it is in motion.
1. Park the unit on level ground.
2. Press and hold the switch to extend the step. The motion will continue until the step is completely
extended when it will automatically stop. Release the switch.
3. Press and hold the switch to retract the step. The motion will stop when the step is completely
retracted. Release the switch.
NOTE: Some step models offer a safety feature which provides automatic closure of the steps when the
vehicle is started.
Rev: 02.08.22 Page 5 CCD-0004560
Wiring Diagram
Diagram 1
"A" connector
"B" connector
"A"
"B"
"A" CONNECTOR
Pin N°
Description
1
Button common (+12 V)
2
--
3
--
4
D +
5
--
6
--
7
RETURN command
8
EXIT command
"B" CONNECTOR
Pin N°
Description
1
(-GND)
2
motor -
3
motor +
4
+12 V dc
Step Open: Alert Indicator will be active when ignition is switched on.
NOTE: D+ should be a positive line that comes from the vehicle any time the parking brake is disengaged
or the ignition is engaged.
Common Button (+12V)
Command
RETURN
Command
EXIT
Command
EXIT
Command
RETURN
Common Button (+12V)
15A Fuse
+12V DC
adjustment screw
Alert Indicator circuit must be ltered to 12V.
Alert Indicator
Rev: 02.08.22 Page 6 CCD-0004560
Wiring Diagram
For Automatic Opening/Closing Kit
Rev: 02.08.22 Page 7 CCD-0004560
Wiring Diagram
For Automatic Opening/Closing Kit (Continued)
Step Open: Alert Indicator will be active when ignition is switched on.
NOTE: D+ should be a positive line that comes from the vehicle anytime the parking brake is disengaged
or the ignition is engaged.
Alert Indicator circuit must be ltered to 12V.
A B
Alert Indicator
Rev: 02.08.22 Page 8 CCD-0004560
Maintenance
1. Make sure unit is parked on a stable, level surface.
2. Make sure power to the unit is turned off and/or disconnected.
Troubleshooting
Prior to starting maintenance procedures, disconnect power to the step’s electrical system to
prevent inadvertent operation of the step.
3. After driving on roads that are salted, wash the step with fresh water.
NOTE: If protective panels need to be removed for service or maintenance, reinstall panels as soon as
possible after service/maintenance has been completed.
Fig. 1
Resources Required
• Phillips screwdriver
Emergency Operation
1. The sliding electric single step is equipped with a manual activation option.
2. Locate the hole under the step.
3. Using a screwdriver, insert it into the hole (Fig. 1).
4. Push up the driving gear with the screwdriver to disengage the electric motor.
5. Move the step to the desired position.
6. Remove the screwdriver to lower the driving gear and stop the step from moving.
Rev: 02.08.22 Page 9 CCD-0004560
Notes
The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (LCI).
LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an
authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.
The information contained in this manual is subject to change without notice and at the sole discretion of LCI.
Revised editions are available for free download from lippert.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert Components, Inc.
Inhaltsverzeichnis
Andere Lippert Autozubehör Handbücher
Lippert
Lippert Sway Command 1.5 Bedienungsanleitung
Lippert
Lippert Thin Shade 806621 Montageanleitung
Lippert
Lippert Curt 60654 Bedienungsanleitung
Lippert
Lippert SolidStep 4.0 Bedienungsanleitung
Lippert
Lippert 2000 Series Bedienungsanleitung
Lippert
Lippert SolidStep Gen 2 Montageanleitung
Lippert
Lippert Promaster Bedienungsanleitung
Lippert
Lippert TI-276 Bedienungsanleitung
Lippert
Lippert Stargazer Nano Wide Skylight Bedienungsanleitung
Lippert
Lippert Level-up Bedienungsanleitung
Lippert
Lippert Stargazer Spirit XTR Bedienungsanleitung
Lippert
Lippert THEATER SEATING Gebrauchs- und Pflegehandbuch
Lippert
Lippert FLYSCREEN N Series Bedienungsanleitung
Lippert
Lippert ARIES S224050 Bedienungsanleitung
Lippert
Lippert Power Steps 2.0 Bedienungsanleitung
Lippert
Lippert Vela Bedienungsanleitung
Lippert
Lippert LUVERNE 401720 Bedienungsanleitung
Lippert
Lippert 45940-85 Bedienungsanleitung
Lippert
Lippert Vela Pop Up Bedienungsanleitung
Lippert
Lippert LatchXtend RV Door Handle Bedienungsanleitung
