MacDon D65 Bedienungsanleitung

1. Park combine and header on a level surface. Ensure

that the combine feederhouse is level.

2. Set header angle to mid-position (between B and C on

the indicator) (not shown).

3. Set the reel fore-aft to mid-position (5 or 6 on reel arm

indicator) (not shown).

4. Lower reel completely.

5. If equipped, set stabilizer/transport wheels to the fully

raised position.

6. Raise header so cutterbar is 6-10 inches (150-250 mm)

above ground.

7. Place header float locks in unlocked (lowered) position.

STEP 1: PRE-ADJUSTMENTS

Complete these 7 steps before adjusting Float.

1. Remove the special torque wrench (A) from storage

position on RH side of the CA25 combine adapter.

2. Place torque wrench (A) on the float lock at (B).

3. Push down on torque wrench (A) until bell crank (C)

rotates forward.

4. Continue pushing down until indicator (D) on wrench

reaches a MAXIMUM reading and begins to decrease.

Note the maximum reading.

5. Refer to TABLE 1 for recommended initial float setting:

 If reading on wrench is high, header is heavy, and

float needs to be increased.

 If reading on wrench is low, header is light, and float

needs to be decreased.

6. Adjust header float to match values in TABLE 1.

Turn each bolt pair equal amounts.

 To increase float (lighten header), tighten (clockwise)

float spring bolts (E) and (F).

 To decrease float (increase header weight), loosen

(counter clockwise) float spring bolts (E) and (F).

 Ensure wrench reading is equal on both sides.

STEP 2: SET HEADER FLOAT

TABLE 1

TORQUE SETTINGS

CUTTING ON

THE GROUND

CUTTING OFF

THE GROUND

20, 25, 30 and 35 FT 1-1/2 to 2 2 to 2-1/2

40 and 45 FT 2 to 2-1/2 2-1/2 to 3

HEADER SIZE

(FT)

LEFT SIDE FLOAT RIGHT SIDE FLOAT

SETTING HEADER FLOAT

IMPORTANT

Be sure to have read your Operator’s

Manual, and complete all set-up tasks

before setting Header Float.

RIGHT SIDE

LEFT SIDE

Light

Off 8 600 - 650 3 10% - 15%

Normal

Heavy

Recommended

Lodged

Off 525 - 600 3 or 4 5% - 10% 4 or 5 Not Required

Light

Off 8 Middle (B) 600 - 650 4 10% - 15%

Normal

Heavy

Recommended

Lodged

Off Steep (D) 525 - 600 3 or 4 5% - 10% 4 or 5 3 Not Required

Light

Off 8 600 - 650 4 10% - 15%

Normal

Heavy

Lodged

Off 525 - 600 3 or 4 5% - 10% 4 or 5

Light

Shallow (A) 600 - 650 2 5%-10% 3

Normal

2 or 3

Heavy

8 3

Lodged

7 Steep (D) 525 - 600 2 5% - 10% 2 or 3

Light

Shallow (A) 600 - 650 5% - 10%

Normal

Heavy

81or2

Lodged

7 Steep (D) 525 - 600 2 or 3 5% - 10%

Light

Steep (D) 600 - 650 10% - 15% 6 or 7

Normal

Heavy

Lodged

Steep (D) 525 - 600 5% - 10%

Light

Steep (D) 600 - 650 10% - 15%

Normal

Heavy

Lodged

Steep (D) 525 - 600 4 5% - 10%

Light

Shallow (A) 600 - 650 10% - 15%

Normal

Heavy

Lodged

Steep (D) 525 - 600 4 5% - 10%

Light

Steep (D) 600 - 650 10% - 15%

Normal

Heavy

Lodged

Steep (D) 525 - 600 3 or 4 5% - 10% 4 or 5

Light

Shallow (A) 600 - 650 10% - 15%

Normal

Heavy

Lodged

Steep (D) 525 - 600 3 or 4 5% - 10% 4 or 5

Light

8 Steep (D) 600 - 650 5% - 10%

Normal

Heavy

Lodged

Steep (D) 525 - 600 5% - 10%

Light

8 Middle (B) 5% - 10%

Normal

Shallow (A)

Heavy

Middle (B)

Lodged

Steep (D) 5% - 10% 3

Light

600 - 650 5% - 10%

Normal

Heavy

Lodged

Steep (D) 525 - 600 5% - 10%

Light

8 600 - 650 5% - 10%

Normal

Heavy

Lodged

Steep (D) 525 - 600 5% - 10%

Soybeans Delta Rice California Rice

Ground4 - 8 in.

Whisker

(Note 5)

Off

OPERATING VARIABLES

Lentils

Ground

Skid Shoe

Position

(Note 4)

Reel Tine

Pitch

Reel

Speed

(Note 3)

Reel

Position

Ground2 - 6 in.

Flax

8 + in. 2 - 6 in. 10+ in.

Stabilizer

Wheel

(Note 4)

Header

Angle

(Note 1)

Knife

Speed

(Note 2)

10+ in.

Peas

Ground

CerealsCanola

Whisker

(Note 5)

Whisker

(Note 5)

4 - 8 in. 4 - 8 In.10+ in. Ground

Draper

Speed

Divider

Rods

6 or 7 Storage1 or 2

Off

On Not Required

RecommendedStorage1 or 2

10%

4 or 5

550 - 600

7600 - 650 2 6 or 7 2 or 3

6 or 7

550 - 600 10%

10%

Variable Not Required

Not RequiredStorage1 or 26 or 7

10%

2 or 3 6 or 7 Not Applicable Variable

550 - 600

210%

6 or 7

Not Required

Not RequiredVariable2 or 3

6 or 7

Not Applicable Variable Not Required

Not RequiredVariable2 or 3

1 or 2 Storage Not Required

RecommendedVariableNot Applicable

Variable Recommended

Variable

2 or 36 or 7

210%

10% Not RequiredNot Applicable

6 or 7

Shallow (A) 550 - 600

Not Required

Middle (B)

Middle (B) 6 or 7

24 or 5

10%

36 or 7

Middle (B) 550 - 600

Middle (B)

2 or 3 10%

Middle (B)

550 - 600Middle (B)

10%

6 or 7

3 or 4

Middle (B)

Shallow (A)

550 - 600

10%1

550 - 600

1 or 2 Storage

On 2

3 or 4

6 or 7

550 - 600

Variable

Crop

Type

Stubble

Height

Crop

Condition

Not Required

10%2550 - 600On 7

Upper Cross

Auger

Notes:

1. Keep header angle

as shallow as

possible. Center link

position depends on

skid shoe and

stabilizer wheel

position. Set header

angle and skid shoe

position to maxi-

mize amount of poly

on the ground while

maintaining desired

cutting height.

2. Minimum knife drive

pulley RPM.

Applicable to only

single knife drive

headers.

3. Percentage above

ground speed.

4. Cutting height is

controlled with a

combination of skid

shoes, stabilizer

wheels and header

angle. By support-

ing header with skid

shoes or stabilizer

wheels, the adapter

floats header over

obstacles and

ground contours.

5. Available through

your Dealer Parts

Department. Set

divider rods to

highest or second to

highest position in

standing crop. This

position allows the

dividers to level the

down crop for a

cleaner cut at the

ends of the header.

Whisker divider not

required on both

ends of header.

Andere Handbücher für D65

Andere MacDon Landwirtschaftliche Geräte Handbücher

MacDon

MacDon R85 Bedienungsanleitung

MacDon

MacDon PW8 Bedienungsanleitung

MacDon

MacDon D65 Bedienungsanleitung

MacDon

MacDon D1 Series Bedienungsanleitung

MacDon

MacDon D1X Series Bedienungsanleitung

MacDon

MacDon PW8 Bedienungsanleitung

MacDon

MacDon 5000 Bedienungsanleitung

MacDon

MacDon NEW HOLLAND D2 Series Bedienungsanleitung

MacDon

MacDon R113 Bedienungsanleitung

MacDon

MacDon FlexDraper FD1 Series Bedienungsanleitung

MacDon

MacDon FlexDraper FD2 Series Bedienungsanleitung

MacDon

MacDon 912 Bedienungsanleitung

MacDon

MacDon NEW HOLLAND D2 Series Bedienungsanleitung

MacDon

MacDon M155 Bedienungsanleitung

MacDon

MacDon R216 Bedienungsanleitung

MacDon

MacDon M Series Bedienungsanleitung

MacDon

MacDon FD75 Bedienungsanleitung

MacDon

MacDon R85 Bedienungsanleitung

MacDon

MacDon R113 Bedienungsanleitung

MacDon

MacDon 973 Bedienungsanleitung

MacDon

MacDon A30-S Bedienungsanleitung

MacDon

MacDon A30-S Bedienungsanleitung

MacDon

MacDon M1170NT5 Bedienungsanleitung

MacDon

MacDon M2170 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung