Mazda 0000-8C-G21A Bedienungsanleitung

GENUINE ACCESSORIES

INSTALLATION INSTRUCTIONS

PART NUMBERS: APPLICABLE MODELS:

0000-8C-Z02 Electrochromic Mirror w/ Compass / HomeLink® 2008 > Mazda Tribute

0000-8C-G21A Compass / HomeLink® Installation Kit

REQUIRED COMPONENTS:

ITEM QTY DESCRIPTION SERVICE PART NUMBER

1 1 Mirror Assembly with Compass and HomeLink®0000-8C-Z02

INSTALLATION KIT COMPONENTS:

2 1 Harness Assembly – Power and Ground 0000-8C-G26

3 2 Wire Tap 0000-8C-H09

4 6 Tie Wrap --

5 1 Wire Retention Clip 0000-8C-G27

6 1 Self-Tapping Hex Screw (8mm) --

7 1 User Guide --

HOMELINK®AND THE HOMELINK HOUSE®ARE REGISTERED TRADEMARKS OF JOHNSON CONTROLS, INC.

TOOLS REQUIRED:

Clean Rag Wire Cutters Power Driver with: Ratchet

Fiberstick Electrical Tape - Socket Adapter Phillip’s Screwdriver

Pliers #T20 Torx - 8mm Socket

Page 1 of 17 9/1/2010

INSTALLATION PRECAUTIONS / NOTES:

•Do not use excessive force when removing OE mirror from windshield.

•Do not place wire harness against objects with sharp edges that may cause electrical

shorting.

•On vehicles equipped with “A” pillar air bag, verify mirror harness path remains clear of

air bag. Harness should follow, and be tied to existing OEM wiring with tie wraps.

•Verify that power harness path will not interfere with brake, clutch, emergency brake or

air bag operation. Use tie wraps to hold the wiring away from critical locations.

Perform the following pre-installation steps:

1. Place kit components on a clean, padded

surface and inspect for damage or defects.

2. Record customer’s programmed radio stations

(if applicable).

1. Disconnect negative battery terminal.

a) Using 8 mm socket, remove negative battery

terminal. (Fig. 1-1)

2. Remove driver-side door seal.

a) Pull back past top of A-pillar trim. (Fig. 1-2)

3. Partially remove A-pillar trim.

a) Using fiber stick, pull the top portion of the A-

pillar trim out toward the passenger-side

approximately ½” to detach (2) clips. (Fig. 1-3)

Fig. 1-1

Negative

Battery

Terminal

1 Preparation

Fig. 1-2

Fig. 1-3

Page 2 of 17 9/1/2010

Page 3 of 17 9/1/2010

Fig. 1-4

b) Grasp A-pillar trim and slide upward. (Fig. 1-4)

c) Rotate A-pillar trim and allow to hang by tether in

order to gain access to A-pillar. Removal of

retaining clip is not needed. (Fig. 1-5)

4. Remove driver side sun visor and bracket.

a) Remove two (2) Phillip’s screws from inner

bracket. (Fig. 1-6)

b) Remove sun visor.

c) Remove one (1) Phillip’s screw from outer bracket.

(Fig. 1-7)

d) Remove sun visor bracket.

Fig. 1-5

NOTE

During reassembly, ensure retaining clip is aligned with slot in

illa

Phillip’s

Screw

Fig. 1-6

Phillip’s

Screw

Fig. 1-7

Retaining Clip

Fig. 1-9

Phillip’s

Screw

Fig. 1-8

5. Remove overhead console.

a) Open sunglass holder and remove two (2)

Phillip’s screws. (Fig. 1-8)

b) Pull toward front of vehicle and downward to remove

overhead console. (Fig. 1-9)

1. Carefully remove OE mirror by pulling downward with

steady, even force until mirror detaches from mounting

button and then slide up. (Fig. 2-1)

1. Attach EC mirror.

a) Hold the mirror head and slide the mount

downwards as far as possible over the windshield

button, until fully seated.

3 EC Mirror Installation

2 Removal of OE Rearview Mirror

. 2-1

Fig. 3-1

1.3 ft-lbs

b) Using a #T20 Torx, tighten the mirror mounting

bracket screw to 1.3 ft-lbs (17.8 kg-cm). (Fig. 3-1)

Page 4 of 17 9/1/2010

. 4-1

1. Plug 10-pin connector into back of EC mirror. (Fig. 4-1)

4 Route EC Mirror Harness to Vehicle Power

NOTE

Slide harness sleeve as close to mirror connector as

ossible.

Wire

Retention

Clip

. 4-2

2. Route EC harness from mirror to headliner.

a) Route power harness toward passenger side

of mirror. (Fig. 4-2)

b) Attach retaining clip to channel mount tubing of

mirror, ensuring clip opening is facing driver side.

(Fig. 4-2)

Fig. 4-3

c) Gain access to overhead by gently pulling down

on headliner and route EC harness from mirror

into vehicle overhead. (Fig. 4-3)

CAUTION

Be careful not to crease headliner.

3. Route EC harness to driver-side A-pillar.

a) Route power harness between vehicle headliner

and roof to top of driver-side A-pillar area.

(Fig. 4-4)

. 4-4

Page 5 of 17 9/1/2010

Tie

Wraps

CAUTION

Fig. 4-5

4. Route EC harness down A-pillar and secure with (3)

small tie wraps as shown. (Fig. 4-5)

CAUTION

Verify mirror harness path is clear of air bag (if equipped).

CAUTION

Do not secure to plastic drain tube if present.

MY 2010

use section:

5c5b

MY 2009

use section:

MY 2008

use section:

The following installation steps in section 5 are model year specific.

Ensure that the model year of the vehicle and the installation steps used

match as noted below:

NOTE

2008 Models

Fig. 5-1

1. Separate EC harness power and ground wires.

5a Connect B+ Constant and Ignition

a) Pull power and ground wires apart (approx. 8

inches). (Fig. 5-1)

Connector C214

Fig. 5-2

2. Attach wire tap connector to +12V ignition in lower

10-pin A-pillar connector.

a) Locate 10-pin connector (C214) on driver side

A-pillar. (Fig. 5-2)

b) Using fiber stick, remove 10-pin connector from

A-pillar. (Fig. 5-2)

Page 6 of 17 9/1/2010

Page 7 of 17 9/1/2010

Fig. 5-3

C214

+12V IGN

c) Locate the Gray wire, Pin #10 (next to Green /

Blue-striped wire in pin #6 and the Yellow /

Green-striped wire in pin #9). (Fig. 5-3)

d) Attach wire tap connector to Gray Wire

approximately ½” down from connector.

(Fig. 5-4)

e) Using pliers, close 2 sides of wire-tap onto wire.

3. Connect EC Power harness to +12V ignition.

a) Insert male spade terminal of Black / White-

striped wire into opening of wire tap on the

Gray wire. (Fig. 5-5)

4. Attach wire tap connector to B+ Constant in upper

10-pin A-pillar connector.

a) Locate the Yellow / Green-striped wire in pin

#5, of the 10-pin upper connector. (Fig. 5-6)

NOTE

Ensure correct wire

in location 10

)

is identified.

Upper

Connector

Grey

Pin #10

Lower

Connector

Fig. 5-4

Fig. 5-5

Ensure male spade connector is fully inserted into wire tap.

Check to see that the spade connector did not miss the slot.

Check to see that it is not visible on either side of the female

connector.

CAUTION

C214

. 5-6 B+ CONSTANT

NOTE

Ensure correct wire

in location 5

)

is identified.

b) Attach wire tap connector to Yellow / Green-

striped wire approximately ½” up from

connector. (Fig. 5-7)

c) Using pliers, close 2 sides of wire-tap onto wire.

(Fig. 5-7)

5. Connect EC power harness to B+ Constant.

a) Insert male spade terminal of Solid Black wire

into opening of wire tap on the Yellow / Green-

striped wire. (Fig. 5-8)

1. Separate EC harness power and ground wires.

a) Pull power and ground wires apart (approx. 8

inches). (Fig. 5-9)

2. Attach wire tap connector to +12V ignition in lower

14-pin A-pillar connector.

a) Locate 14-pin connector (C214) on driver side

A-pillar. (Fig. 5-10)

Yellow / Green

Pin #5

Lower

Connector

Upper

Connector

Fig. 5-7

Fig. 5-8

Ensure male spade connector is fully inserted into wire tap.

Check to see that the spade connector did not miss the slot.

Check to see that it is not visible on either side of the female

connector.

CAUTION

Fig. 5-9

5b Connect B+ Constant and Ignition

2009 Models

Fig. 5-10

Connector C214

b) Using fiber stick, remove 14-pin connector from

A-pillar. (Fig. 5-10)

Page 8 of 17 9/1/2010

c) Locate the Blue wire, Pin #11 (across from

Green / Red-striped wire in pin #4 and the

Gray / Violet-striped wire in pin #3).

(Fig. 5-11)

d) Attach wire tap connector to Blue Wire

approximately ½” down from connector.

(Fig. 5-12)

e) Using pliers, close 2 sides of wire-tap onto wire.

3. Connect EC Power harness to +12V ignition.

a) Insert male spade terminal of Black / White-

striped wire into opening of wire tap on the

Blue wire. (Fig. 5-13)

Fig. 5-11

C214

+12V IGN

NOTE

Ensure correct wire

in location 11

)

is identified.

Upper

Connector

Blue

Pin #11

Lower

Connector

Fig. 5-12

Fig. 5-13

Ensure male spade connector is fully inserted into wire tap.

Check to see that the spade connector did not miss the slot.

Check to see that it is not visible on either side of the female

connector.

CAUTION

Fig. 5-14

C214

B+

4. Attach wire tap connector to B+ Constant in upper

14-pin A-pillar connector.

a) Locate the Yellow / Green-striped wire in pin

#5, of the 14-pin upper connector. (Fig. 5-14)

NOTE

Ensure correct wire

in location 5

)

is identified.

Page 9 of 17 9/1/2010

Page 10 of 17 9/1/2010

Connector C214

Fig. 5-18

Fig. 5-17

Fig. 5-16

Yellow / Green

Pin #5

Lower

Connector

Upper

Connector

Fig. 5-15

c) Attach wire tap connector to Yellow / Green-

striped wire approximately ½” up from

connector. (Fig. 5-15)

d) Using pliers, close 2 sides of wire-tap onto wire.

(Fig. 5-15)

5. Connect EC power harness to B+ Constant.

a) Insert male spade terminal of Solid Black wire

into opening of wire tap on the Yellow / Green-

striped wire. (Fig. 5-16)

1. Separate EC harness power and ground wires.

b) Pull power and ground wires apart (approx. 8

inches). (Fig. 5-17)

5c Connect B+ Constant and Ignition

2010 and Newer Models

Ensure male spade connector is fully inserted into wire tap.

Check to see that the spade connector did not miss the slot.

Check to see that it is not visible on either side of the female

connector.

CAUTION

2. Attach wire tap connector to +12V ignition in lower

20-pin A-pillar connector.

c) Locate 20-pin connector (C214) on driver side

A-pillar. (Fig. 5-18)

d) Using fiber stick, remove 20-pin connector from

A-pillar. (Fig. 5-18)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mazda Autozubehör Handbücher

Mazda

Mazda MVG 4507 F Bedienungsanleitung

Mazda

Mazda KPF1 V3 460 Leitfaden

Mazda

Mazda Auto-Dimming Mirror Bedienungsanleitung

Mazda

Mazda 0000 81 L25 Bedienungsanleitung

Mazda

Mazda Bluetooth Handsfree System Bedienungsanleitung

Mazda

Mazda CB01-V4-701 Bedienungsanleitung

Mazda

Mazda C830-V7-050A Bedienungsanleitung

Mazda

Mazda 0000-8E-G01 Bedienungsanleitung

Mazda

Mazda TD11 V3 460F Leitfaden

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda KA0G V1 370 Bedienungsanleitung

Mazda

Mazda TD91 79 CFZ Bedienungsanleitung

Mazda

Mazda 0000-8E-N31 Bedienungsanleitung

Mazda

Mazda BDEL-V7-410 Bedienungsanleitung

Mazda

Mazda 4100-78-828A Bedienungsanleitung

Mazda

Mazda 0000-8G-N03 Bedienungsanleitung

Mazda

Mazda 0000-8P-R04 Bedienungsanleitung

Mazda

Mazda CX-3 Bedienungsanleitung

Mazda

Mazda 0000-8G-K02 Bedienungsanleitung

Mazda

Mazda DC3L-V1-370A Bedienungsanleitung

Mazda

Mazda 0000-89-N01 Bedienungsanleitung

Mazda

Mazda KMV6V7210 Bedienungsanleitung

Mazda

Mazda GENUINE ACCESSORIES Bedienungsanleitung

Mazda

Mazda 0000-8L-L2 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung