Mazda 0000-8G-N03 Bedienungsanleitung

AS 090-M11415cma1209

Page 1 of 4

Genuine Accessories

Installation Instructions

Part Number

0000-8G-N03

Applicable Models:

2010 CX-9

Package Contents

Front Mask

Tools Required

Stubby Phillips

Screwdriver

Snap Head Screw (Qty. 4)

Front End Cover (Qty. 1)

0Before Installation

A. Area to be covered by mask must be clean. It is recommended that you wash and wax vehicle prior to installation.

B. Both vehicle and mask must be completely dry prior to installation. If moisture under mask is allowed to dry on

vehicle, paint may cloud.

C. Any repainted surfaces in contact with mask must be allowed to cure completely. Consult paint manufacturer or

repair facility if you are not sure.

1Install Hood Cover

A. With hood open, stretch hood cover (A)

onto hood, pulling each side one or two

inches at a time, until corners fit snugly.

Install hooks on ends of straps (B,C)

into corresponding holes on underside

of hood. Pull evenly on ends of

adjustable straps (B) until tight. Secure

loose ends in elastic loops.

Hood Cover (Qty. 1)

Plastic Washer (Qty. 4)

U-Nut (Qty. 4)

Scissors

Page 2 of 4

AS 090-M11415cma1209

2Remove wheel well fasteners

A. Using stubby phillips screwdriver, remove upper and

lower plastic fasteners along front edge of both front

wheel wells corresponding to snaps on mask. A. In both front wheel wells, lift wheel well liner to reveal

holes.

B. Slip u-nuts (D) over holes in metal edge that correspond

to the front mask. Make sure that the holes are aligned

properly.

C. Release liner to its original position. Using a stubby

phillips screwdriver, install washer (E) and snap head

screws (F) into holes with newly installed u-nuts.

3Install wheel well hardware

Cut outs on front end cover

A. If your vehicle has fog lights, remove

cut outs in area shown using the

following method:

a) Using a pair of scissors and

working from the back side of

the mask, cut the stitching

(thread) along all sides that

are holding the cut outs (G) to

mask.

Note: Be careful not to cut the felt

or thread under the cut outs.

Improper removal will result in

damage to the mask.

Page 3 of 4

AS 090-M11415cma1209

6Install upper attachments

A. On driver’s side, insert small pads (J) into space at

center below headlight. Slide fully inserted pads towards

wheel well. Repeat on opposite side.

5Install upper attachments

A. On driver’s side of vehicle, attach clips (H) to back edge

of air intake grille. Repeat on opposite side.

B. On driver’s side of vehicle, attach attach elastic with hook

(I) to back edge of upper grille support. Repeat on

opposite side.

Install wheel well attachments

A. Press snaps (L) onto snap head screws (F) in both front

wheel wells.

B. Attach clips (M) to edge of both front wheel wells.

7Install upper attachments

A. On driver’s side, insert large pads (K) in slots around

inside edge of headlight. Repeat on opposite side.

Page 4 of 4

AS 090-M11415cma1209

12 Care and Cleaning

A. Always remove mask before washing vehicle.

B. Hand clean mask using mild soap, rinse thoroughly with

clean water and line dry completely. Do not machine dry!

C. Use Mazda Vinyl/Leather Protectant (or equivalent) to

preserve color and finish.

D. WARNING: Running up on curb will damage this product.

Manufacturer will not be responsible for damage to product

due to accident or misuse.

11 Post Installation Inspection

A. Close hood and check alignment between hood cover

and front end cover along seam (between fender and

hood). If adjustment is necessary, adjust the hood cover

by adjusting the hood cover straps. Refer to step 1.

B. If mask should flap due to high speed or wind conditions,

adjust or remove mask completely.

10 Install bottom attachments

A. Attach clips (P) to back edge of

bottom vent.

B. Attach elastics with hooks (Q) to

edge of lower fascia.

Install lower vent attachments

A. Attach elastics with hooks (N) to rear edge of

lower vent.

B. Attach plastic clip (O) to rear edge of lower

vent.

Andere Mazda Autozubehör Handbücher

Mazda

Mazda C830-V7-050A Bedienungsanleitung

Mazda

Mazda 0000-8L-K01 Bedienungsanleitung

Mazda

Mazda TD11 V3 460F Leitfaden

Mazda

Mazda KA0G V1 370 Bedienungsanleitung

Mazda

Mazda KPF1 V3 460 Leitfaden

Mazda

Mazda 0000-8G-L12 Bedienungsanleitung

Mazda

Mazda 0000-89-N01 Bedienungsanleitung

Mazda

Mazda 6 GJ 2.2 D 2012 Bedienungsanleitung

Mazda

Mazda 2005 Miata MX-5 Bedienungsanleitung

Mazda

Mazda GS2A -V1-132 Bedienungsanleitung

Mazda

Mazda CX-9 Bedienungsanleitung

Mazda

Mazda 0000-8G-K05 Bedienungsanleitung

Mazda

Mazda 0000-8C-Z02 Bedienungsanleitung

Mazda

Mazda 0000-8K-L05 Bedienungsanleitung

Mazda

Mazda A2DP Bedienungsanleitung

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda 0000-8L-G03A Bedienungsanleitung

Mazda

Mazda 0000-8G-K02 Bedienungsanleitung

Mazda

Mazda 0000-8E-N31 Bedienungsanleitung

Mazda

Mazda 0000-8P-R04 Bedienungsanleitung

Mazda

Mazda 0000-8L-R02 Bedienungsanleitung

Mazda

Mazda 0000-8C-Z05 Bedienungsanleitung

Mazda

Mazda 0000 81 L25 Bedienungsanleitung

Mazda

Mazda 0000-8L-L2 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung