Mazda 0000-8E-R10 Bedienungsanleitung

GENUINE ACCESSORIES

Installation Instructions

Supplemental Trailer Hitch Harness

Part Number:

2017 > CX-5 (GAS 2.5L)0000-8E-R10

Applicable Models:

Tools Required Before Installation

Large Tie

Wraps

(QTY 7)

Installation

Instructions

Drill &

6mm Drill Bit

Wire Cutters

1.) Read installation instructions before

proceeding.

2.) Be careful not to damage vehicle paint

or kit components.

3.) Do not over tighten bolts, tighten to

speciﬁed torque.

Page 1 of 10

(QTY 1)

Package Contents:

Tape

Measure

Page 2 of 10

Tools Needed:

Wire Cutters

1. Underneath vehicle, cut all existing tie

wraps attaching 4-Flat trailer harness to

vehicle using wire cutters.

2. Leave ﬂoor grommet from interior of

vehicle containing 4-Flat trailer harness

seated. Do not remove.

3. Remove harness connector from hitch

bracket.

4. Harness should be free at this point and

only attached at grommet.

FRONT

Tie Wrap

(LARGE)

Tow Hitch Cross Member

UNDERSIDE OF VEHICLE

Tie Wrap

(LARGE)

Tie Wrap

Hitch Plate

4-Flat Harness

Floor Grommet

FACTORY

HARNESS

FACTORY

HARNESS

4-Flat Harness Routing Overview

CAUTION

Make sure not to damage

any factory harnesses

during removal.

A4-FLAT HARNESS TIE WRAP REMOVAL

Take caution not to damage or cut trailer hitch harness or any

factory installed harnesses during the removal of the ties wraps.

CRITICAL

STEP

4-Flat

Harness

Tie Wrap

Page 3 of 10

BDRILL HOLE IN BUMPER FASCIA

Drill + 6mm bit

Tape Measure

Tools Needed:

1. Locate attachment point (a) on the bumper

fascia to measure the drill point for the

tie wrap attachment. Measure 40mm towards

the receiver tube of the hitch and 15mm

upwards. Drill a 6mm hole at the drill point.

Continues on next page

DRILL HERE

40mm

15mm

Bumper fascia

mount

(a)

REFERENCE IMAGE

Bumper

Fascia

(a)

DRILLED HOLE

Tow Hitch Cross Member

UNDERSIDE OF VEHICLE

4-Flat Harness Routing Overview

Tie Wrap

(d)

Tie Wrap

(e)

Tie Wrap

(a) Tie Wrap

(b)

Tie Wrap

(c)

4-FLAT HARNESS REROUTE TO HITCH RECEIVER

1. Starting at grommet area, route

4-Flat trailer harness over top of hitch

attachment bracket in direction towards

hitch receiver tube.

1.1

4-Flat

Trailer Harness

Grommet

Hitch Attachment

Bracket

Receiver

Tube Cross

Member

1.2

2. Route 4-Flat trailer harness underneath

hitch cross member and up towards the

fascia support bracket.

Cross

Member

Bottom

Receiver

Tube

3. Route 4-Flat trailer harness behind

fascia support bracket making sure

the harness is routed between the

bumper fascia and bracket.

Bumper fascia

support bracket

Cross

Member

Page 4 of 10

1. After performing Step 1, verify that a minimum of 50mm has been achieved

between exhaust and harness. If not, remove tie wrap and repeat Step 1

above using a new tie wrap. If 50mm has been achieved, move on to Step 2.

Due to the extreme high temperatures produced by the exhaust, a minimum

clearance of 50mm must be maintained between exhaust and harness.

Failure to do so will result in severe damage to harness and loss of trailer

functions, such as brake light and turn signal lights.

CRITICAL

STEP

Page 5 of 10

Continues on next page

Exhaust

Tie Wrap

(a)

1. Secure the 4-FLATtrailer connector into the hitch bracket as shown.

Remove all slack in the wiring towards the drilled hole (a). Use a large tie

wrap to fully secure the wire harness ensuring a 50mm clearance from the

indented section of the exhaust closest to the harness as shown in the

measurement photo and make sure to remove all slack. It’s important that

the corrugated tube is routed over the edge of the bracket for protection.

CRITICAL

STEP

4-FLAT

connector

Hitch Bracket

Edge of

Bracket

Corrugated

Tube

CRITICAL

STEP

It’s important that the corrugated tube is routed over the edge of the bracket for

protection. Damage to harness may occur otherwise.

CRITICAL

STEP

50mm

Tools Needed:

Wire Cutters

Tie Wraps

Large

ESECURE 4-FLAT HARNESS FROM HITCH TO VEHICLE

Page 6 of 10

2. After the distance veriﬁcation trim the

cable tie using the wire cutters and

rotate the tie wrap head up so it is

not visible from the rear of the vehicle

to avoid injury.

3. Conﬁrm harness is routed between the

bumper fascia and support bracket. If

so, remove all slack between tie wrap

location (a) and tie wrap location (b)

and use a large tie wrap to secure

harness to support bracket, tighten the

tie wrap and trim the tie wrap tail with

wire cutters.

4. Use a large tie wrap (c) to secure

the harness to the bottom of the

cross member of the hitch. Tie

wrap should be located 100mm

from cross member end. Remove

all slack, tighten the tie wrap and

trim the tie wrap tail with wire cutters.

(b)

(a)

Support

Bracket

(a)

TOP

Cross

Member

Cross

Member

Cross

Member

Cross

Member

Bottom

(c)

Continues on next page

Tie Wrap

ROTATE UP

HEAD UP

100mm

Page 7 of 10

Cross

Member

5. While removing all slack, use a large tie wrap

to secure the harness to the hitch attachment

bracket (d). Tighten the tie wrap and trim the

tail using wire cutters.

6. Remove all the slack in the harness near the wire attachment point near the grommet.

This is located on the rear side of the bumper deﬂector (e). Use a large tie wrap to

secure the harness to the attachment point. Remove all slack, tighten the tie wrap and

trim the tie wrap tail using wire cutters.

(c)

EFINISHING STEPS

(d)

Attachment

Bolt

5-6 Grommet

(e)

(d)

4-Flat

Trailer Harness

Tie Wrap

Page 8 of 10

TROUBLESHOOTING GUIDE

TRAILER HITCH WIRING KITAPPLICA BLE M ODELS:

2017> CX-5

PAR T NUM BER:

0000-8E-R07A

0000-89-R32A

TOOLS REQUIRED

 

METHOD

1aeeggooeooeaeof e

aefaoeo

Poeeaof efeaeaoofoe

oeao go ee

efo eo

a o

o e

See Fig.1 page 14

TOOLS REQUIRED

TEST LIGHT

METHOD

1. Attach the test light ground connection to the male pin of the

harness’s 4-ﬂat connector.

2. Probe each of the female pins individually to conﬁrm correct

circuit operation. Right Turn/Stop Green

Left Turn/Stop Yellow

Tail Brown

Ground White

0000-8E-R10 2017 > CX-5 (GAS 2.5L)

APPLICABLE MODELS

PART NUMBER:

Page 9 of 10

INSTALLATION INSPECTION

TRAILER HITCH WIRING KIT

Inspection Parts Clearance/Fit

Scratches/Dirt/

Harness

Interference

Installation/

Tightening/

Engagement

Operation

Check

Tow Harness Functions

Tow Harness

Tow Harness Module Ground

Screw

Driver’s Side Left Rear Interior

Trim Panel

Passenger Side Right Rear Interior

Trim Panel

Rear Threshold Plate

Rear Foam Inserts

Rear Floor Covering

Vehicle Negative Power Cable

4-FLAT Harness

50mm Between Exhaust & Harness

Inspect the installed / reinstalled parts for the following items:

0000-8E-R10

PART NUMBER:

2017 > CX-5 (GAS 2.5L)

APPLICABLE MODELS

Notes:

1. Verify signal functionality at the trailer harness plug using test procedure on page 8.

2. Ensure tow harness module ground bolt is torqued to 7.0 N m.

Page 10 of 10

Date

Vehicle

VIN

Checked Person in

Charge

If the battery is disconnected, the power windows may no longer fully open or fully

close automatically.

1. Turn the ignition key to the “ON” position.

2. Press the power window switch to fully open the power windows.

3. Lift up the power window switch to fully close the power windows, and keep it pulled up

for approximately 2 seconds.

4. Position the engine switch at “OFF”, and then at “ON” again. When the function doesn’t work

after these procedures, please contact your Mazda dealer.

CAUTION

If the battery is disconnected, the DSC may stop operating.

(The DSC OFF indicator will flash at this time, and the TCS/DSC operation indicator will illuminate.)

1. Turn the ignition switch to “OFF” and then turn it back to “ON”.

2. Turn the steering wheel clockwise as far as it will go, and then turn it back counterclockwise as far as it

will go.

3. Check that the TCS/DSC operation indicator is turned off.

4. Turn the ignition switch to “OFF” and then turn it back to “ON”.

5. Check that the TCS/DSC operation indicator is turned off. If the TCS/DSC operation indicator is still

illuminated or the DSC indicator is not turned off when the ignition switch is turned back to “ON”, contact

your Mazda dealer.

CAUTION

1. After performing Step 1 on page 5, verify that a minimum of 50mm has been achieved

between exhaust and harness. If not, remove tie wrap and repeat Step 2

using a new tie wrap. If 50mm has been achieved, move on to Step 3.

Due to the extreme high temperatures produced by the exhaust, a minimum

clearance of 50mm must be maintained between exhaust and harness. Failure to do

so will result in severe damage to harness and loss of trailer functions, such as

brake light and turn signal lights.

Inhaltsverzeichnis

Andere Mazda Autozubehör Handbücher

Mazda

Mazda 0000-8G-L12 Bedienungsanleitung

Mazda

Mazda 0000-8E-N31 Bedienungsanleitung

Mazda

Mazda 0000-8G-K05 Bedienungsanleitung

Mazda

Mazda CX-9 Bedienungsanleitung

Mazda

Mazda Auto-Dimming Mirror Bedienungsanleitung

Mazda

Mazda 0000 81 L25 Bedienungsanleitung

Mazda

Mazda 4100-78-828A Bedienungsanleitung

Mazda

Mazda A2DP Bedienungsanleitung

Mazda

Mazda KMV6V7210 Bedienungsanleitung

Mazda

Mazda 6 GJ 2.2 D 2012 Bedienungsanleitung

Mazda

Mazda GENUINE SIDE UNDER SPOILER Bedienungsanleitung

Mazda

Mazda C830-V7-050A Bedienungsanleitung

Mazda

Mazda KPF1 V3 460 Leitfaden

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda CT-L1005 Installationsanleitung

Mazda

Mazda MVG 4507 F Bedienungsanleitung

Mazda

Mazda 2005 Miata MX-5 Bedienungsanleitung

Mazda

Mazda 0000-8P-R04 Bedienungsanleitung

Mazda

Mazda TD11 V3 460F Leitfaden

Mazda

Mazda 0000-8C-Z05 Bedienungsanleitung

Mazda

Mazda DC3L-V1-370A Bedienungsanleitung

Mazda

Mazda 0000-8L-G03A Bedienungsanleitung

Mazda

Mazda DN4J-V7-110 Bedienungsanleitung

Mazda

Mazda 0000 8C Z01 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung