Mazda 0000-8G-L12 Bedienungsanleitung

AS 090-M11411cma0709

Page 1 of 8

Genuine Accessories

Installation Instructions

Part Number

0000-8G-L12

Applicable Models:

2010 > Mazda 3 s-model w/o Air Dam

Package Contents

Front Mask

Tools Required

Stubby Phillips

Screwdriver

Scissors

Front End Cover (Qty. 1)

0Before Installation

A. Area to be covered by mask must be clean. It is recommended that you wash and wax vehicle prior to installation.

B. Both vehicle and mask must be completely dry prior to installation. If moisture under mask is allowed to dry on

vehicle, paint may cloud.

C. Any repainted surfaces in contact with mask must be allowed to cure completely. Consult paint manufacturer or

repair facility if you are not sure.

D. Dealers should provide all customers with a copy of these installation instructions for future reference.

1Cut out license plate flap on front end cover

A. If state or provincial law requires

use of front license plate, cut

hole out in license plate cutout

area (A) using scissors. Slip

opening around bracket.

Caution: Cut out section

previous to mask installation,

making sure to not cut elastic

straps.

U-Nut (Qty. 8)

Snap Head Screw (Qty. 8)

Washer (Qty. 8)

Page 2 of 8

AS 090-M11411cma0709

A. With hood open, lay front end cover over front of vehicle. On both sides of vehicle slip pocket (E) over edge of upper bumper

bracket above headlight.

B. Attach clips (F) to upper edge of bumper facia on both sides of hood latch.

4Install upper attacments

3Install wheel well hardware

A. In both front wheel wells, lift wheel well liner to reveal holes.

B. Slip u-nuts (B) over holes in metal edge that correspond to

the front mask. Make sure that the holes are aligned

properly.

C. Release liner to its original position. Using a stubby phillips

screwdriver, install washer (C) and snap head screws (D)

into holes with newly installed u-nuts.

2Remove wheel well fasteners

A. Using stubby phillips screwdriver, remove the four plastic

fasteners illustrated below along front edge of both front

wheel wells.

Page 3 of 8

AS 090-M11411cma0709

8Install lower vent attachments

A. Attach 4 elastics with

hooks (K) to back edge of

grill at top of lower air

vent.

B. Attach 5 elastics with

hooks (L) to back edge of

grill at bottom of lower air

vent.

6Install pads at headlights

A. On driver’s side, insert pads (H) in slots around headlights.

Repeat on passenger’s side of vehicle.

5Install wheel well attachments

A. Press 4 snaps (G) onto snap head screws (D) in

both front wheel wells. Assistance may be

required to evenly pull mask to snaps.

7Install upper vent attachments

A. Attach 2 clips (I) to back

edge of facia at bottom of

upper air vent.

B. Attach 4 elastics with

hooks (J) to back edge of

facia at top of upper air

vent.

Page 4 of 8

AS 090-M11411cma0709

11 Post Installation Inspection

A. If mask should flap due to high speed or wind

conditions, adjust or remove mask completely.

12 Care and Cleaning

A. Always remove mask before washing vehicle.

B. Hand clean mask using mild soap, rinse thoroughly with

clean water and line dry completely. Do not machine dry!

C. Use Mazda Vinyl/Leather Protectant (or equivalent) to

preserve color and finish.

D. If mask is left on vehicle in rain, dirt can potentially be

washed under the mask and could scratch the vehicle. It

is recommended that the mask be removed and cleaned

along with vehicle as instructed if left on during rain, sleet

or snow.

E. WARNING: Running up on curb will damage this product.

Manufacturer will not be responsible for damage to product

due to accident or misuse.

10 Install lower bumper attachments

A. Attach 4 elastics with hooks (N) to holes on underside of

bumper.

9Install side lower attachments

A. On both sides of vehicle, attach 2 clips (M) to underside

of bumper.

Inhaltsverzeichnis

Andere Mazda Autozubehör Handbücher

Mazda

Mazda 0000-8G-N03 Bedienungsanleitung

Mazda

Mazda KPF1 V3 460 Leitfaden

Mazda

Mazda 6 GJ 2.2 D 2012 Bedienungsanleitung

Mazda

Mazda 0000 81 L25 Bedienungsanleitung

Mazda

Mazda 0000-8P-R04 Bedienungsanleitung

Mazda

Mazda DN4J-V7-110 Bedienungsanleitung

Mazda

Mazda 0000-89-N01 Bedienungsanleitung

Mazda

Mazda CX-5 Bedienungsanleitung

Mazda

Mazda TD91 79 CFZ Bedienungsanleitung

Mazda

Mazda BDEL-V7-410 Bedienungsanleitung

Mazda

Mazda 0000-8C-Z02 Bedienungsanleitung

Mazda

Mazda GENUINE ACCESSORIES Bedienungsanleitung

Mazda

Mazda 0000-8G-K02 Bedienungsanleitung

Mazda

Mazda 0000-8G-K05 Bedienungsanleitung

Mazda

Mazda 0000-8K-L05 Bedienungsanleitung

Mazda

Mazda CB01-V4-701 Bedienungsanleitung

Mazda

Mazda A2DP Bedienungsanleitung

Mazda

Mazda Highbay BY007P Bedienungsanleitung

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda KMV6V7210 Bedienungsanleitung

Mazda

Mazda PROTEGE 5 Bedienungsanleitung

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda 0000-8E-G01 Bedienungsanleitung

Mazda

Mazda 0000-8E-R10 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung