MELICONI SPEEDY 210 STB Bedienungsanleitung

Thank you for choosing MELICONI.

This simplified universal remote control contains all the main functions of most TV and digital

terrestrial and/or satellite decoder (STB) remote controls.

Before programming and using the remote control, fit the batteries.

Keep your Instructions and Code Booklet for future reference.

USING THE KEYS AND FUNCTIONS

FITTING THE BATTERIES

SET-UP

Read these instructions carefully before programming your remote control!

To command your appliances, you must program your Speedy 210 STB as described in

paragraphs Aor Bbelow.

Visit out Internet site www.meliconi.com for interactive instructions for easy and fast remote

control programming. Warning: programme one appliance at a time.

Before programming and using the remote control, fit the batteries.

The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown.

• The batteries must be changed once a year.

• Change the batteries if the light indicator starts to flash during use.

The batteries are low.

• This remote control has a permanent memory and does not lose the

programmed codes when the batteries are removed.

• Make a note of the code for your TV on the adhesive label supplied

inside the battery cover. This note will be handy if you have to

reprogram your remote control.

ON/OFF key to turn the appliance off,

or in some cases on.

Control the volume using

To select an external input terminal.

To select the next program or

to turn ON your TV.

Mute key.

Control the volume using

Teletext keys:

to access Teletext

close Teletext and return to

normal viewing

Numeric keypad.

Light indicator.

Selection key to control the decoder.

To select the previous program or

to turn ON your TV.

Selection key to control the TV.

istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 5

Identify the code and make a note of it following the code noting procedure

(see “PROGRAMMED CODE NOTING” section).

1. Turn on the appliance to be programmed and select a programme.

2. Look for your TV brand in the list of codes at the end of this booklet and make a note of the

corresponding code indicated alongside (e.g. Philips 0025). If your TV brand is not listed, apply the global

search described in paragraph B.

3. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down

for five seconds until the light indicator at the top starts flashing to indicate that the remote control is

programming.

4. Release the keys, Within 15 seconds, enter the brand code previously identified (e.g. 0025). The light

indicator flashes more quickly to indicate that the remote control is ready for the search.

5. Point the remote control at the appliance. Press and release the key slowly several times and stop

when the appliance goes off (you may have to press the key dozens of times).

6. When the appliance goes off, press the key to confirm.

Three long flashes indicate that the operation has been completed correctly.

Additional check

Check that some of the other functions used on your original remote control are working correctly. If the

commands function incorrectly or erratically, you have probably entered a code for a similar but different

remote control. In this case, repeat the search procedure from point 3.

HOW TO PROGRAMME THE REMOTE CONTROL

NOTE: during the search operation, the light indicator flashes more quickly. The light indicator

stops flashing and the remote control leaves the programming mode in the following cases:

• if no keys are pressed for 12 seconds

• if the code search list is completed. In this case, switch to programming mode B

This operation may take a few minutes.

1. Turn on the appliance to be programmed and select a programme.

2. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down

for five seconds until the light indicator at the top starts flashing to indicate that the remote control is

programming.

3. Release the keys. Within 15 seconds, enter the code 0000.

The light indicator flashes more quickly to indicate that the remote control is ready for the search.

4. Point the remote control at the appliance. Press and release the key slowly several times. Stop when

your appliance goes OFF (you may have to press the key over a hundred times).

5. When the appliance goes off, press the key to confirm. Three long flashes indicate that the

operation has been completed correctly.

Additional check

Check that some of the other functions used on your original remote control are working correctly.

If the commands function incorrectly or erratically, you have probably entered a code for a similar but

different remote control.

In this case, repeat the search procedure from point 2.

GLOBAL SEARCH REMOTE CONTROL PROGRAMMING

istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 6

Identify the code and make a note of it following the code noting procedure

(see “PROGRAMMED CODE NOTING” section).

NOTE: during the search operation, the light indicator flashes more quickly. The light indicator

stops flashing and the remote control leaves the programming mode in the following cases:

• if no keys are pressed for 12 seconds.

• if the code search list is completed. In this case, visit www.meliconi.com

Always write down the 4-digit codes for your remote control on the label inside the battery cover

after running the search and saving the codes.

This may be useful if you need to reprogram your remote control in the event of accidental

cancellation.

To find the codes for your remote control:

1. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down

for five seconds until the light indicator at the top starts flashing to indicate that the remote control is

programming.

2. After releasing the keys enter the code number you noted down previously. Three flashes indicate that

the code has been saved correctly. If not, try the code entry procedure again from point 1.

PROGRAMMED CODE NOTING

1. Hold the selection key whose code you are looking for down for five seconds until the light indicator at

the top starts flashing to indicate that the remote control is programming.

2. Release the selection key ( or ) and then press and release the key within eight seconds.

3. After a few seconds, the light indicator communicates the code you are looking for by flashing the four

numbers separately. Count the number of flashes for each code number. For example, for the code 1306,

the key flashes one, three, ten and six times to give:

= 1

= 3

= 0

= 6

4. Note this code on the label inside the battery cover, for rapid consultation.

RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN

TV FUNCTIONS ALWAYS ACTIVE

The MUTE, VOLUME -, VOLUME + keys can also be used to control the decoder. To use these functions on

the digital decoder, press the corresponding key while holding the STB key down at the same time.

istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 7

TROUBLESHOOTING

PROBLEM

The appliance does not respond and the light

indicator does not light up when you press a

key.

The appliance does not respond but the light

indicator lights up.

When a key is pressed, the light indicator

flashes and the appliance does not respond

to the commands.

The remote control commands are not all

working correcting.

The code for your appliance brand is not in

the list of codes of the end of this booklet.

SOLUTION

Check that the batteries are fitted correctly. If

necessary, replace them with 2 new 1.5 V

AAA/LR03 alkaline batteries.

Check that the batteries are new and that the

remote control is pointing at the appliance

without any obstacles in the way. If required,

reset the remote control code, following the

programming procedure A or B.

The batteries are low. Change them.

You may have used the wrong code. Reset

the remote control code, following the

programming procedure Aor B .

Set the remote control code, following the

global search programming procedure B.

WARRANTY: 2 years

The warranty ceases to be valid if the product is tampered with or

used incorrectly.

Remote control model Speedy 210 STB

Purchase date

If you have any queries about Speedy 210 STB:

•read this booklet carefully– this will help you to solve almost all problems

•consult our Internet site www.meliconi.com to answer all your queries more easily and quickly.

Agent's stamp

INFO LINE

istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 8

Andere MELICONI Fernbedienung Handbücher

MELICONI

MELICONI GumBody Personal 1 Bedienungsanleitung

MELICONI

MELICONI Personal 3 plus Installations- und Betriebshandbuch

MELICONI

MELICONI GUMBODY FACILE SMART Bedienungsanleitung

MELICONI

MELICONI Speedy 2.1 BIG Bedienungsanleitung

MELICONI

MELICONI Control TV.1 Bedienungsanleitung

MELICONI

MELICONI GUMBODY FACILE 100 Bedienungsanleitung

MELICONI

MELICONI TLC01 Bedienungsanleitung

MELICONI

MELICONI MYCRO Bedienungsanleitung

MELICONI

MELICONI GumBody Universal 5 web Bedienungsanleitung

MELICONI

MELICONI GumBody DIGITAL 2 SMART Bedienungsanleitung

MELICONI

MELICONI SPEEDY 110 Bedienungsanleitung

MELICONI

MELICONI Speedy 210 combo Bedienungsanleitung

MELICONI

MELICONI TLC02 Bedienungsanleitung

MELICONI

MELICONI EASY 300 Bedienungsanleitung

MELICONI

MELICONI PRATICO 2 Light Bedienungsanleitung

MELICONI

MELICONI GUMBODY UNIVERSAL 3-300 Bedienungsanleitung

MELICONI

MELICONI LOGIC12 Bedienungsanleitung

MELICONI

MELICONI SPEEDY 2 Bedienungsanleitung

MELICONI

MELICONI Control 5 500 PLUS Bedienungsanleitung

MELICONI

MELICONI pratico 6 Installations- und Betriebshandbuch

MELICONI

MELICONI CONTROL 4 Plus Bedienungsanleitung

MELICONI

MELICONI Facile 5.1 LED Bedienungsanleitung

MELICONI

MELICONI TLC05 Bedienungsanleitung

MELICONI

MELICONI Speedy 100 plus Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung