Mercia Garden Products 01DTPRMSHDB1008DDOP-V1 Gebrauchsanweisung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

01DTPRMSHDB1008DDOP-V1

DIP TREATED PREMIUM SHIPLAP DUTCH BARN 10X8 DOUBLE DOOR OPENING WINDOW

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 1

Please retain product label and instructions for future reference

General Instructions

P 2

01DTPRMSHDB1008DDOP-V1

Overall Dimensions:

Width = 2539mm

Depth = 2970mm

Height = 2626mm

Base Dimensions:

Width = 2350mm

Depth = 2912mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Gable Strip 12x121x2090mm QTY 2

WB-2090MM

Butt Hinge QTY 4

PI-07-0066

Felt QTY 2

PI-01-0015

15 Door Cloaking Strip 27x44x1670mm QTY 1

F2744-1670MM

16 Door Strip 12x45x1449mm QTY 1

S1245-1449MM

17 Door Strip 12x45x1772mm QTY 2

S1245-1772MM

18 Window Strip 12x56x1037mm QTY 2

S1256-1037MM

19 Cover Trims 12x56x1790mm QTY 7

S1256-1790MM

Barge Board 12x95x678mm QTY 1

S1295-G-678MM

Barge Board 12x95x734mm QTY 2

S1295-G-734MM

Fascia 12x95x900mm QTY 4

S1295-G-900MM

Fascia 12x95x662mm QTY 4

S1295-G-662MM

Casement Stay QTY 2

PI-07-0007

T Hinge QTY 6

PI-07-0021

Tower Bolt QTY 2

PI-07-0030

Turn Button QTY 2

PI-07-0034

Hasp and Staple

Lock QTY 1

PI-07-0221

Weatherproof Lock QTY 1

PI-07-0222

30 Door Blocks

27x44x150mm QTY 2

F2744-150MM

31 Truss Blocks

27x44x100mm QTY 2

F2744-G-120MM

23 Bottom Door Framing 27x44x1336mm QTY 1

F2744-1336MM

29 Truss Brace 27x44x1640mm QTY 2

F2744-G-1680MM

U Channel QTY 4

PI-07-0013

Joining Plates QTY 6

PI-07-0220

1311 12

Top Roof QTY 4

AI-S21MBDBR1473X654-V1

Bottom Roof QTY 4

AI-S21MBDBR1473X898-V1

Window QTY 2

AI-FW1000X540-V1

Floor Blocks

27x44x400mm QTY 10

F2744-400MM

568

Front Panel QTY 2

AI-S21SHPPTOV512X1761-V1

Door QTY 2

AI-S21FBMBZBD676X1770-V1

Gable Top Left QTY 2

AI-S22HDBGTL1180X817-V1

Gable Top Right QTY 2

AI-S22HDBGTR1180X817-V1

Lower Truss QTY 2

AI-S22HDBTF800X88-V1

Upper Truss QTY 2

AI-S22HDBTF629X88-V1

Window Panel QTY 2

AI-01S21SH1LFW1417X1814-V1

Floor QTY 4

AI-S21MBF1456X1175-V1

Back Panel

Width 1180mmQTY 2

AI-S21SHPP1180X1796-V1

Side Panel

Width 1417mm QTY 2

AI-S21SHPP1417X1814-V1

20 Gable Cover Trims

12x56x710mm QTY 1

S1256-710MM

22 Top Door Framing 44x44x1800mm QTY 1

F4444-1800MM

21 Top Door Framing

44x44x280mm QTY 2

F4444-280MM

50mm Screw x 95

Felt Tacks x 155

16mm Screw x 24

30mm Screw x 251

60mm Bolt x 8

20mm Screw x 9

60mm Screw x 8

40mm Screw x 48

100mm Screw x 2

P 3

Please retain product label and instructions for future reference

Nail Bag

There may be extra screws present in the nail bag

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

Pre drill

hole

50mm

screw

Step 1

Parts Needed- No.1 QTY 4

Place the oor panels (No.1) onto a rm

and level base. Ensure the base has

suitable drainage, free from areas where

standing water can collect.

Secure the oors together using 8x50mm

screws through the oor bearers in an

alternating pattern.

Repeat the step to create two oor

assemblies.

16x50mm Screws

Pre drill

hole

40mm

screw

Step 2

Parts Needed- No.14 QTY 10

Locate the Floor Blocks (No.14) between

the oor framing, ensuring they are

spaced equally.

Secure to the oor using 2x40mm screws

per block, going through the oor

cladding and into the oor blocks below.

20x40mm Screws

Step 3

Pre drill

hole

40mm

screw

Locate the second oor assembly along

side the rst oor assembly.

Secure to the oor using 2x40mm screws

per block, going through the oor

cladding and into the oor blocks below.

20x40mm Screws 1

FRONT

BACK

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

Step 4

Parts Needed- No.2 QTY 1

- No.3, (or 4) QTY 1

**Please note: These side panels are

interchangeable. Decide which layout

works best for you before assembly.**

Locate the Back Panel (No.2) and the Side

panel (No.3) (or Window Panel) onto the

oor, secure the panels at the corner

using 3x50mm screws.

Do not secure the building to the oor

until the roof is tted.

Position the panels so there is equal

spacing.

**Please note: The Side Panels are

slightly higher than the back panels.**

3x50mm Screws

FRONT

BACK

PANEL

SIDE

PANEL

Pre drill

hole

50mm

screw

Locate the Second Back Panel (No.2) and

Side panel (No.3) (or Window Panel) onto

the oor, secure the panels at the joins

using 3x50mm screws per join in an

alternating pattern.

Do not secure the building to the oor

until the roof is tted.

Position the panels so there is equal

spacing.

**Please note: The Side Panels are

slightly higher than the back panels.**

6x50mm Screws

Step 5

Parts Needed- No.2 QTY 1

- No.3, (or 4) QTY 1

FRONT

BACK

PANEL

SIDE

PANEL

Pre drill

hole

50mm

screw

Step 6

Parts Needed- No.4, (or 3) QTY 1

Locate the Window Panel (No.4) (or Side

Panel) onto the oor, secure the panels at

the corner using 3x50mm screws.

Do not secure the building to the oor

until the roof is tted.

Position the panels so there is equal

spacing.

**Please note: The Side Panels are

slightly higher than the back panels.**

3x50mm Screws

BACK

PANEL

SIDE

PANEL

BACK

FRONT

Pre drill

hole

50mm

screw

Locate the Second Window Panel (No.4)

(or Side Panel) onto the oor, secure the

panels at the joins using 3x50mm screws

per join in an alternating pattern.

Do not secure the building to the oor

until the roof is tted.

Position the panels so there is equal

spacing.

**Please note: The Side Panels are

slightly higher than the back panels.**

3x50mm Screws

Step 7

Parts Needed- No.4, (or 3) QTY 1

BACK

PANEL

SIDE

PANEL

BACK

FRONT

P 5

Please retain product label and instructions for future reference

Pre drill

hole

50mm

screw

Locate the Front Panels (No.6) onto the

oor, secure the panels at the corners

using 3x50mm screws per join.

Do not secure the building to the oor

until the roof is tted.

Position the panels so there is equal

spacing.

**Please note: The Front Panels are

slightly lower than the side panels.**

6x50mm Screws

Step 8

Parts Needed- No.6 QTY 2

FRONT

PANEL

SIDE

PANEL

Pre drill

hole

Locate the Top Door Framings (No.21 and

No.22) onto the top of the front panels,

the framing should be really ush to the

back edges of the framing within front

panels.

Secure the framing using 8x60mm screws,

ensuring to go through the top door

framing, and into the front panel framing.

Locate the Bottom Door Framing (No.23)

between the front panels. Do Not secure

the Bottom Door Framing to the oor until

the roof is tted.

**Please note: The Front Panels are

slightly lower than the side panels.**

8x60mm Screws

Step 9

Parts Needed- No.21 QTY 2

- No.22 QTY 1

- No.23 QTY 1

60mm

screw

FRONT

PANEL

SIDE

PANEL

Pre drill

hole

50mm

screw

Lay the Gable tops (No.7 and No.8) along

side each other, ensure they are ush at

the bottom. Secure together using

4x50mm screws in an alternating pattern.

Repeat step to create a second assembly.

8x50mm Screws

Step 10

Parts Needed- No.7 QTY 2

- No.8 QTY 2

Pre drill

hole

50mm

screw

Locate the Gable tops (No.7 and No.8)

onto the top of the front and back panels.

Slot the groove of the boarding within

the Gable Tops on to the tongues within

the plain panels below. Secure the gable

tops from above using 6x50mm screws

per gable top.

Ensure the gable tops are ush with the

ends of the panels as shown in the

diagram.

Do not secure the building to the oor

until the roof is tted.

12x50mm Screws 8

Step 11

P 6

Please retain product label and instructions for future reference

Pre drill

hole

30mm

screw

Locate the Gable Strips (No.28) onto the

join of the gable tops and front/back

panels, secure the gable strips using

4x30mm screws per strip in an alternating

pattern. Do not x into the gap between

the panels.

8x30mm Screws

Step 12

Parts Needed- No.28 QTY 2

Pre drill

hole

40mm

screw

30mm

screw

Place all of the required parts together on

the oor in the correct layout as shown in

the illustration. Secure the Joining plates

(No.41) to both sides of the truss along

the framing joins with 5x30mm screws

per plate, ensuring the screws are

staggered to avoid collision.

Secure the Truss Brace (No.29) to both

sides of the Lower Trusses, making sure to

stagger the 4x40mm screws at each end.

The truss brace should nish ush with

the edge of the lower truss.

30x30mm Screws

8x40mm Screws

Step 13

Parts Needed- No.9 QTY 2

- No.10 QTY 2

- No.29 QTY 2

- No.41 QTY 6

41 41

b99

10 10

Pre drill

hole

50mm

screw

100mm

screw

Measure and mark 42mm from the top

corner of the truss.

Place the Truss in position with a 42mm

gap from the top corner of the truss to

the top of the side panel.

Locate the Truss Blocks (No.31) onto each

side of the building, then use the

measurement made when together with

the truss to determine the height of the

Truss blocks and mark the position.

Secure the truss blocks in an alternating

pattern using 2x50mm screws per block,

ensuring to go through to the panel

framing behind. Do not x into the gap

between the panels.

Fix the truss to the side panels using

1x50mm screw per side making sure that

you go into the panel framing behind.

Fix a further 100mm screw to each side

from the exterior of the building into the

truss on the inside.

6x50mm Screws

2x100mm Screws

Step 14

Parts Needed- No.31 QTY 2

10 10

31 31

42mm

P 7

Please retain product label and instructions for future reference

Step 15

Parts Needed- No.12 QTY 4

- No.40 QTY 2

Locate the Bottom roof panels (No.12)

and secure the roof panels together using

a U channel (No.40) on to the top framing

pieces. Ensure the U channel (No.40) is

equally spaced over the roof panel

framing. Secure the U channels using

10x30mm screws per channel.

Repeat the step to create a second

assembly.

20x30mm Screws

Pre drill

hole

30mm

screw

Top

Bottom

Step 16

Parts Needed- No.11 QTY 4

- No.40 QTY 2

Locate the Top roof panels (No.11) and

secure the roof panels together using a

U channel (No.40) on to the top

framing pieces.

Make sure that the U channel is on the

framing within the roof panel where

there is the 16mm gap between the

top of the framing and the edge of the

roof cladding. Ensure the U channel

(No.40) is equally spaced over the roof

panel framing. Secure the U channels

using 10x30mm screws per channel.

Repeat the step to create a second

assembly.

20x30mm Screws

Pre drill

hole

30mm

screw

Top

Bottom

11mm

16mm

Place the Bottom roof panels (No.12) on

top of the gables and truss, ensuring they

are correctly orientated with the U channel

slotted into the roof truss.

Step 17

12 12

Pre drill

hole

30mm

screw

Secure the Roofs using 4x30mm screws

per roof, ensuring to go through the

roof cladding and into the gable top

framing and the truss framing below.

Position the panels so there is equal

spacing.

**Make sure that the edges of the

framing within the roof panels are

ush with the outer cladding on the

front and back panels.**

Do not secure the building to the oor

until the roof is tted.

16x30mm Screws

Step 18

Please retain product label and instructions for future reference

P 8

Place the Top Roof Panels (No.11) on top

of the gables and truss, ensuring they are

correctly orientated with the U channel

slotted into the top of the roof truss.

Step 19

16mm

11mm

Pre drill

hole

30mm

screw

Secure the Roofs using 4x30mm screws

per roof, ensuring to go through the

roof cladding and into the gable top

framing below and the truss framing

below.

Position the panels so there is equal

spacing.

**Make sure that the edges of the

framing within the roof panels are

ush with the outer cladding on the

front and back panels.**

Do not secure the building to the oor

until the roof is tted.

16x30mm Screws

Step 20

16mm

11mm

Pre drill

hole

50mm

screw

Once the roof is xed, attach the

building to the Floor with 50mm

screws.

Ensure the screws go through the

panel into the Floor framing.

28x50mm Screws

Step 21

Pre drill

hole

50mm

screw

Make sure that the Bottom Door

Framing (No.23) is ush with the

framing within the front panels. Fix

the Bottom Door Framing to the

oor ensuring that you go into the

framing below.

4x50mm Screws

Step 22

P 9

Please retain product label and instructions for future reference

Pre drill

hole

30mm

screw

Fix 3 Hinges (No.33) to each Door

(No.5) securing with 4x30mm

screws per hinge and position as

shown.

Fix each Door to the building with

3x30mm screws per hinge. Make

sure that the inside view of the door

looks like it does on the illustration.

Ensure the doors open and close

freely.

42x30mm Screws

Step 24

Parts Needed- No.5 QTY 2

- No.33 QTY 6

*Inside View*

SECONDARY PRIMARY

Pre drill

hole

30mm

screw

Place the Door Blocks (No.30) onto the

top of the door framing and ensure that

they are ush with the ends of the

framing. Secure using 2x30mm screws

per block, going through the front of

the door cladding and into the door

block.

Locate the Door Cloaking Strip (No.15)

between the door framing and ensure

that it is equally spaced. Secure to the

secondary door using 4x30mm screws,

going through the front of the door

cladding and into the Door Cloaking

Strip.

8x30mm Screws

Step 25

Parts Needed- No.15 QTY 1

- No.30 QTY 2

30 30

30mm

screw

Pre drill

hole

Locate the Door Strips (No.16 & No.17)

around the door opening and ensure

they are ush with the framing.

There should be a gap between the

strips and the door opening as shown.

Secure each strip with 4x30mm screws,

going through the strips and into the

door panel cladding.

12x30mm Screws

Step 23

Parts Needed- No.16 QTY 1

- No.17 QTY 2

Step 26

Parts Needed- No.34 QTY 2

Pre drill

hole

30mm

screw

Align the tower bolts (No.34) onto

the door cloaking strip, secure the

bolts to the top and bottom using

6x30mm screws per tower bolt.

Mark the position of the bolt

& drill a hole above and below for

the bolt to catch in to.

12x30mm Screws

P 10

Please retain product label and instructions for future reference

P 7

Step 27

Parts Needed- No.39 QTY 2

Pre drill

hole

60mm

Bolts

Align the lock (No.39) to the door, ensuring

equal spacing across the doors and in line

with the door framing.

Measure and mark the holes of the lock

(No.39) and drill through the boards and

through the framing and door blocks.

Fix the lock onto the door using 8x60mm

Carriage Bolts and Nuts

8x60mm Carriage Bolts

Step 28

Parts Needed- No.35 QTY 2

Pre drill

hole

30mm

screw

Attach the turn buttons (No.35) to the

secondary door at the top and bottom

using 1x30mm screw per turn button.

2x30mm Screws

30mm

16mm

Opening Window

Fixed Window

30mm

screw

16mm

screw

Place the Window Strip (No.18) 11mm above

the window gap in the window panel and x

with 3x30mm screws per strip.

6x30mm Screws

If you would like the windows to be opening

use the Butt Hinges (No.36) to attach to the

window strip and the Window (No.13)

together. Use 30mm screws to x the butt

hinge to the Window Strip and 16mm screws

to x it to the Window.

12x30mm Screws

12x16mm Screws

If you want to x the windows, instead of

xing butt hinges to the opening window,

use 4x30mm screws to attach the window

(No.13) to the window side panel as shown

in the diagram.

8x30mm Screws

Pre drill

hole

Step 29

Parts Needed- No.13 QTY 2

- No.18 QTY 2

- No.36 QTY 4

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 03DTSHPN1006FGD2TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB0808DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1408DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0608SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTMBPN0503DD-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products SELF BUILD PACK Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04GREEN0806SD-V6 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02DTTWRS0605-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619WKNE2633LBDD1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA1010DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0409SHPB-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL0808DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0409DSHPB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTODB0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RANE4535FGDD2TW1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBP0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644LOG186-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTMBPN0406STP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02STRPCK1412-V1 Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung