Mercia Garden Products 01OVLPA1010DDFW-V1 Bedienungsanleitung

10X10 OVERLAP APEX SHED

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips

screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of

heavy or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also

occur during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be

avoided but can be helped. It is suggested that the outdoor building is sprayed with water during extended

periods of warm sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to

prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof

treatment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The

cladding should overlap the base, creating a run o for water. It is also recommended that the oor be at least

25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting

or using this product.

Refer to the instructions pages for you specic product code

**Protim Aquatan T5 (621)**

Your building has been treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

H=220cm W=140cm L=130cm

P 2

01OVLPA1010DDFW-V1 & 01OVLPA1010DDNW-V1

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

01OVLPA1010DDFW-V1-NW

01OVLPA1010DDFW-V1

Overall Dimensions:

Length = 3028mm

Width = 3095mm

Height = 2257mm

Base Dimensions:

Length = 2974mm

Width = 2974mm

Building Content:

13456

Plain Side QTY 2

(NW ONLY)

AI-01OVLPPSS1490X1567-V1

Window Side QTY 2

(FW ONLY)

AI-01OVLPWS1490X1567-V1

Floor QTY 4

AI-01OVLPF1487X1487-V1

Roof Sheet QTY 4

PI-03-0232

Front Gable Right

QTY 1

AI-01OVLPFGR796X1929-V1

Front Gable Left

QTY 1

AI-01OVLPFGL796X1929-V1

Front Gable Top

QTY 1

AI-01OVLPFGT1332X452-V1

Back Gable

Right QTY 1

AI-01OVLPHPGR1462X2226-V1

Back Gable

Left QTY 1

AI-01OVLPHPGL1462X2226-V1

Door QTY 2

AI-01MBDR1780X661-V1

Door Strip - 12x60x830mm QTY 2

S1260-830mm

Ridge Bar - 27x70x1462mm QTY 2

F2770-1462mm

Truss Block - 44x44x140mm QTY 2

F4444-160mm (140mm nished length)

Floor Blocks - 28x28x400mm QTY 8

F2828-400mm

Door Gable Bottom Rail - 28x28x1332mm QTY 1

F2828-1332mm

Door Block - 28x28x140mm QTY 2

F2828-140mm

Truss QTY 1

AI-01TRS2924X690-V1

Fascia - 12x60x1667mm QTY 4

S1260-1667mm

Plain Gable Strip - 12x45x2164mm QTY 1

S1245-2164mm

Cover Trim - 12x45x1575mm QTY 6

S1245-1575mm

Door Beading Strip - 12x28x1720mm QTY 2

S1228-1720mm

Finial QTY 2

DIAMOND SHED FINIAL

Door Gable Strip - 7x125x1875mm QTY 1

OP7125-1875mm

Eaves Frame - 28x28x1502mm QTY 4

F2828-1502mm

Window Strip - 12x30x546mm QTY 10 (FW ONLY)

S1230-546mm

Plastic Window Cill QTY 2 (FW ONLY)

PI-08-0001

T Hinge QTY 6

PI-02-1045

Felt

Turn Button QTY 3

PI-07-0034

Styrene QTY 4 (FW ONLY)

PI-05-0114

L-Bracket QTY 2

PI-07-0012

Nail Bag 30mm Screw x 147

20mm Screw x 32

30mm Black Screw x 3

50mm Screw x 60

70mm Screw x 7

40mm Screw x 130

Felt Tacks x 170

16mm Screws x 25

100mm Screw x 3

U Channel QTY 1

PI-07-0013

P 3

Remove transportation

blocks from the bottom of

each panel before

beginning assembly. Each

Panel should have two

blocks.

Pre Assembly

Door Gable Assembly

Step 1

2 x 50mm screws

Lay the Front Gable Right and Front Gable

top on a level oor place them next to each

other, ensure they are level at the top then

x together using 2x50mm screws. Stagger

the screws so they do not collide.

Step 2

2 x 50mm screws

Lay the Front Gable Left next to the Front

Top Gable, ensure they are level at the top

then x together using 2x50mm screws.

Stagger the screws so they do not collide.

Line the Door Gable Strip up to the

assembled gable at the corners as shown in

the illustration and x in place using 40mm

screws

6 x 40mm screws

50mm

screw Pre drill

hole

50mm

screw Pre drill

hole

40mm

screw Pre drill

hole

Please retain product label and instructions for future reference

P 4

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Plain Gable Assembly

Step 3

10 x 50mm screws

Lay the Back Left Gable and Back Right

Gable on a level oor place them next to

each other, ensure they are level at the top

and bottom then x together using

10x50mm screws. Stagger the screws so

they do not collide.

50mm

screw Pre drill

hole

Step 4

8 x 40mm screws

Place oor on rm and level base, ensure

base has suitable drainage free from areas

where water can collect. (See front page on

base requirements).

Attach the oors using 8 x 40mm screws

40mm

screw Pre drill

hole

40mm

screw Pre drill

hole

Fix another two oor panels using

the oor blocks provided.

Place the oor blocks in between

the framing as shown in the

diagram.

Screw the oor blocks to oor

using 2x40mm screws per block

screwing through the oor into

the oor blocks.

Fix the two oor panels together

using the same method shown in

step 4 using 8x40mm screws.

Repeat this step once more if you

are assembling the 15x10 and

another two times if you are

assembling the 20x10.

10x10 - 24x40mm screws

15x10 - 48x40mm screws

20x10 - 72x40mm screws

Step 5

15x10

20x10

Please retain product label and instructions for future reference

P 5

Please retain product label and instructions for future reference

Do not secure the building to

the oor until the roof is tted.

Fix the corners with 50mm

screws as shown in diagram.

Position the panels so there is equal spacing

between the oor and cladding on all 4 sides

Step 6

3x50mm Screws

50mm

screw Pre drill

hole

Step 7

Fix the remaining plain side and

a window side at the corners

with 50mm screws as shown in

diagram.

6x50mm Screws

50mm

screw Pre drill

hole

Step 8

Fix the remaining window side at

the corners with 50mm screws as

shown in diagram.

Continue to add window sides and

plain sides using the same method

if you are assembling a 15x10 or

20x10.

For a 15x10 you will have an extra

Plain and Window Side panel.

For a 20x10 you will have extra two

Plain and Window sides.

10x10 - 3x50mm Screws

15x10 - 9x50mm Screws

20x10 - 15x50mm Screws

15x10

20x10

50mm

screw Pre drill

hole

Please retain product label and instructions for future reference

P 6

Step 9

Fix the Door Gable (refer to steps 1

and 2 if you have not already

assembled this) at the corners with

50mm screws as shown in diagram.

6x50mm Screws

50mm

screw Pre drill

hole

Step 10

Fit the Door Gable Bottom rail

between the Front Gable Left and

Right. Fix to the oor using 3x50mm

screws making sure the screws go

through to the oor framing.

3x50mm Screws

50mm

screw Pre drill

hole

Fix the T Hinges onto the

doors and door gable as

shown. Ensure that the screws

go through the cladding and

into the framing behind.

42x30mm screws

Step 11

Internal View

30mm

screw Pre drill

hole

Please retain product label and instructions for future reference

P 7

Step 12

Place a Truss central to where two

panels join. Align the top of the

truss with the top of the sides as

shown in the diagram.

HINT - Use a piece from the xing

kit as a guide.

Pencil mark the truss position and

remove truss.

Place the truss blocks up to the

pencil mark and x using 2x70mm

screws per block.

Place the truss back into position on

top of the support block and secure

using 100mm screw each side from

the top down through the truss and

into the block.

10x10 - 4x70mm Screws

2x100mm Screws

15x10 - 8x70mm Screws

4x100mm Screws

20x10 - 12x70mm Screws

6x100mm Screws

For 15x10 and 20x10 build a truss

where each panel joins, for 15x10

you will have two trusses and for the

20x10 you will have three trusses.

13 13

15x10

20x10

70mm

screw Pre drill

hole

100mm

screw Pre drill

hole

Step 13

15x10

20x10

10x10 - 2x70mm Screws

8x30mm Screws

15x10 - 4x70mm Screws

8x30mm Screws

20x10 - 6x70mm Screws

8x30mm Screws

Place the two ridge bars in between

the front and back panels. Ensure

the top corners of the support bar

are ush with each top point. Secure

in place using the L Bracket on each

end with 4x30mm screws. Using a

70mm screw secure the ridge bar to

the truss by screwing through the

underneath of the truss into the

ridge bar.

For a 15x10 building you will need

to add another Ridge Bar.

For a 20x10 building you will need

to add another two ridge bars.

30mm

screw

Pre drill

hole

70mm

screw

Pre drill

hole

Please retain product label and instructions for future reference

P 8

15x10

20x10

Step 14

Place two roof sheets ontop of the

plain gable and truss making sure

the roof sheet sits ush to the

ouside edge of the plain gable and

x using 40mm screws. Before

xing the roof sheet to the truss

frame make sure the edge of the

roof sheet sits in the middle of the

truss then x using 40mm screws.

8x30mm Screws

24x40mm Screws

Fix the eaves frame to the

roof sheet using 4x30mm

screws for each sheet.

233

40mm

screw Pre drill

hole

30mm

screw Pre drill

hole

Step 15

Fix the remaining eaves frames

to the remaining roof sheets

using 4x30mm screws per sheet.

Place the roof sheet ontop of

the truss and ensure that it

butts up to the one already

xed. Fix in place with 40mm

screws ensuring they go

through to the framing.

For 15x10 & 20x10 buildings

continue this process untill the

roof is complete.

10x10 - 8x30mm Screws

24x40mm Screws

15x10 - 16x30mm Screws

48x40mm Screws

20x10 - 24x30mm Screws

72x40mm Screws

15x10

20x10

30mm

screw Pre drill

hole

40mm

screw Pre drill

hole

Please retain product label and instructions for future reference

P 9

Step 16

Once the roof is xed

attatch the building to the

oor with 50 mm screws.

10x10 - 24 x 50mm Screws

15x10 - 40 x 50mm Screws

20x10 - 56 x 50mm Screws

15x10

20x10

50mm

screw Pre drill

hole

Step 17

HANDLE

WITH CARE

10x10 - 170 x felt tacks

15x10 - 240 x felt tacks

20x10 - 310 x felt tacks

Cut four strips of felt and place

onto the roof. See below for

sizes.

Place the felt at onto the roof

in the order that is stated on

the diagram below.

Once the sheets are laid out x

them onto the roof with tacks

100mm apart.

Felt Strip Sizes

10x10 - 3100mm

15x10 - 4600mm

20x10 - 6100mm

Felt

tacks Pre drill

hole

Please retain product label and instructions for future reference

P 10

Step 18

Fit the cover trims to the

building and secure in place

with 40mm screws as

shown.

Fit the Plain Gable Strip

where the two back gables

join using 4x40mm screws.

Pre drill to avoid splitting.

10x10 - 22x40mm Screws

15x10 - 28x40mm Screws

20x10 - 34x40mm Screws

22 18

15x10

20x10

40mm

screw Pre drill

hole

Step 19

16x40mm Screws

Attatch faisca’s to the

roof leaving a slight

overhang at the top.

Fit the fascias to the

roof over the felt and

secure in place with

40mm screws as

shown.

Pre drill to avoid

splitting.

25 20

15x10

20x10

40mm

screw Pre drill

hole

Please retain product label and instructions for future reference

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 0644CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03OVLPBRN0705-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0608SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBA0707DDSW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCORSE0409-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBP0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRA0301-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA0808FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619PNNE0324HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RANE0504FGDD2TW1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02DTTWR0605-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG015-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0407DSHSA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02BRAM0806-V3-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0304SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB0808DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644LOG186-V4 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung