Mercia Garden Products 01DTPRMSHPN1408DDOP-V1 Gebrauchsanweisung

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building has been treated by the

correct application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

01DTPRMSHPN1408DDOP-V1

DIP TREATED PREMIUM SHIPLAP PENT 14X8 DOUBLE DOOR OPENING WINDOW

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 1

Please retain product label and instructions for future reference

General Instructions

P 2

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

01DTPRMSHPN1408DDOP-V1

Please retain product label and instructions for future reference

Overall Dimensions:

Width =4160mm

Depth = 2484mm

Height = 2167mm

Base Dimensions:

Width = 4100mm

Depth = 2350mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Window Panel QTY 1

AI-01S21SH1LFW1418X2079-V1

Door Panel QTY 1

AI-01S21SHDD1418X2079-V1

Door QTY 2

AI-S21FBMBZBD551X1742-V1

Floor QTY 4

AI-R11MBF2050X1175-V1

Roof QTY 4

AI-S21MBPR1034X2470-V1

Right Gable Top QTY 1

AI-S21SHPGTR2360X342-V1

Left Gable Top QTY 1

AI-S21SHPGTL2360X342-V1

Framed Window QTY 1

AI-FW1000X540-V1

Fascias 12x90x2494mm QTY 2

S1290-2494MM

13 Door Block 27x44x160mm QTY 4

F2744-160MM

Ridge Bar 27x70x2012mm QTY 2

F2770-2012MM

15 Floor Blocks 28x28x400mm QTY 8

F2828-400MM

16 Eaves Framing 28x28x1034mm QTY 8

FS2828-1034MM

17 Door Beading Strips 12x40x1686mm QTY 2

S1240-1686MM

18 Door Cover Trims 12x56x860mm QTY 1

S1256-860MM

20 Window Cover Trim 12x56x1038mm QTY 1

S1256-1038MM

21 Cover Trims 12x56x1770mm QTY 7

S1256-1770MM

Cover Trims 12x56x2072mm QTY 5

S1256-2072MM

Fascias 12x90x2068mm QTY 4

S1290-2068MM

U-Channel QTY 1

PI-07-0013

Corner Brace QTY 2

PI-07-0012

Felt QTY 1

Butt Hinge QTY 2

PI-07-0066

T-Hinge QTY 6

PI-07-0021

Lock Hasp QTY 1

PI-07-0221

Turn Button QTY4

PI-07-0034

Casement Stay QTY 1

PI-07-0007

Padlock QTY 1

PI-07-0222

19 Door Cover Trims 12x56x820mm QTY 1

S1256-820MM

Back Panel 1418mm QTY 2

AI-S21SHPP1418X1774-V1

Side Panel 1180mm QTY 4

AI-S21SHPPTOV1180X1753-V1

7 8

Front Panel QTY 2

AI-S21SHPPTF594X2079-V1

Back Panel 2 QTY 2

AI-S21SHPP594X1774-V1

P 3

Please retain product label and instructions for future reference

Step 2

Parts needed- No.1 QTY 2

Secure the Floor (No. 1) to the assembly

from Step 1, using 8x30mm screws per oor.

Repeat this to create two assembled oors

16x30mm Screws

Pre drill

hole

30mm

screw

Pre drill

hole

50mm

screw

Place the assembled oor panels

(No. 1) upside down onto a rm and

level base. Ensure the base has

suitable drainage, free from areas

where standing water can collect.

Secure the oors together using

18x50mm screws through the oor

bearers in an alternating pattern.

Once xed together turn the oor

back the right way up.

18x50mm Screws

Step 3

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

50mm Screw x 130

40mm Screw x 33

Felt Tacks x 220

20mm Screw x 10

30mm Screw x 152

60mm Bolt x 8

70mm Screw x 26

100mm Screw x 10

16mm Screw x 6

Nail Bag

There may be extra screws present in the nail bag

Step 1

Parts needed- No.1 QTY 2

-No.15 QTY 8

Secure the Floor (No. 1) to the

Floor Blocks (No. 15) using 8x30mm

screws per oor.

Repeat this for one other oor

panel.

16x30mm Screws

Pre drill

hole

30mm

screw

P 4

Please retain product label and instructions for future reference

Place the Side panel (No.5) and

the Back panel 2 (No.7) onto the

oor, Fix the panels at the corner

using 3x50mm Screws

Place the Back Panel 1 (No.6)

next to the Back panel 2 and x

together using 3x50mm screws.

Do not secure the building to

the oor until the roof has

been tted.

Position the panels so there is

equal spacing between the

oor and cladding on all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

Place the Side panel (No.5) and the Back

panel (No.6) onto the oor, Fix the

panels at the ends of the standing panels

using 3x50mm Screws

Do not secure the building to the

oor until the roof has been tted.

Position the panels so there is equal

spacing between the oor and

cladding on all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

Place the Front panel (No.8) and the

Back panel 2 (No.7) onto the oor, Fix

the panels at the corner using

3x50mm Screws.

Do not secure the building to the

oor until the roof has been tted.

Position the panels so there is equal

spacing between the oor and

cladding on all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

SECONDARY PRIMARY

*Inside View*

Fix the T Hinges (No.28) onto the

doors (No.3) and Door Panel (No.2)

as shown using 7x30mm screws per

t-hinge

Ensure that the screws go through

the cladding and into the framing

behind.

42x30mm Screws

Step 4

Parts needed- No.2 QTY 1

-No.3 QTY 2

-No.28 QTY 6

Pre drill

hole

30mm

screw

Step 5

Parts needed - No.5 QTY 1

- No.6 QTY 1

- No.7 QTY 1

Step 6

Parts needed - No.5 QTY 1

- No.6 QTY 1

Step 7

Parts needed - No.7 QTY 1

- No.8 QTY 1

P 5

Please retain product label and instructions for future reference

Place the Side panel (No.5) onto the

oor, Fix the panels at the corner using

3x50mm Screws.

Place the Window Panel (No.4) along

side the Front panel (No.8) and x at

the ends using 3x50mm screws.

Do not secure the building to the

oor until the roof has been tted.

Position the panels so there is equal

spacing between the oor and

cladding on all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 8

Parts needed - No.4 QTY 1

- No.5 QTY 1 Place the Door panel (No.2) onto the

oor, between the Window panel and

the front panel. Fix the panels at the

ends using 3x50mm Screws.

Do not secure the building to the

oor until the roof has been tted.

Position the panels so there is equal

spacing between the oor and

cladding on all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 10

Parts needed - No.2 QTY 1

Place the Front panel (No.8) and the

Side panel (No.5) onto the oor, Fix

the panels at the corner using

3x50mm Screws.

Do not secure the building to the

oor until the roof has been tted.

Position the panels so there is equal

spacing between the oor and

cladding on all sides.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 9

Parts needed - No.5 QTY 1

- No.8 QTY 1

Place the Left Gable (No.9) and the

Right Gable (No.10) onto the side

panels, ensuring the boards

interlock.

Secure in place using 4x50mm

screws per gable top, screwing in an

alternating pattern.

Using 2x50mm screws, x the gables

to the front panels at the corners.

8x50mm Screws

Pre drill

hole

50mm

screw

Step 11

Parts needed - No.9 QTY 1

- No.10 QTY 1

P 6

Please retain product label and instructions for future reference

Step 12

Pre drill

hole

30mm

screw 25

Connect the ridge bars (No.14) together

with the metal “U” (No.25) channel, using

10x30mm screws.

Attach the “L” (No.29) brackets to each

end of the Ridge support with 2x30mm

screws per bracket.

*Ensure the bracket are ush with the

ends of the ridge bar.

14x30mm Screws

Parts Needed - No.14 QTY 2

- No.25 QTY 1

- No.29 QTY 2

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

Align the ridge bar (No.14)

between the gables and secure to

the central uprights with 2x30mm

screws per bracket (No.29), as

shown in the illustration.

*Ensure the ridge bar is ush with

the top framing of the gable tops.

4x30mm Screws

Step 13 Step 15

Parts needed- No.11 QTY 4

Step 14

Parts needed - No.11 QTY 4

- No.16 QTY 8

50mm

screw

Pre drill

hole

Fix the Eaves framing (No.16) to the roof

(No.11) using 3x50mm screws per eaves

framing, screwing through the eaves framing

and into the roof framing.

Ensure the eaves framing is ush to the

edges of the roof framing before securing

24x50mm Screws

Place the Roofs (No.11) onto the top

of the building, ensuring the side

edges are ush with the building

and there is equal spacing at the

front and back.

Fix the Roofs together internally,

using 9x40mm screws in alternating

sides as shown in the diagram.

9x40mm Screws

40mm

screw

Pre drill

hole

*internal view*

11 11 11

P 7

Please retain product label and instructions for future reference

Step 16

Step 17

Fix the roofs (No.11) to the top of

the building, ensuring the side

edges are ush with the building

and there is equal spacing at the

front and back.

Using 26x70mm Screws, x the roof

(No.11) around each edge, ensuring

the screws go through to the panel

framing below.

26x70mm Screws

70mm

screw

Pre drill

hole

Using 10x100mm screws, x the roof

(No.11) onto the ridge bar (No.14),

ensuring to go through the roof

framing and into the ridge bar

10x100mm Screws

100mm

screw

Pre drill

hole

11 11 11 11

Step 18

50mm

screw

Pre drill

hole

Once the roof is xed, attach the

building to the oor with 50mm

screws.

Ensure the screws go through the

panel into the oor framing

32x50mm Screws

bbbb

Step 19

Parts needed - No.18 QTY 1

- No.19 QTY 1

- No.27 QTY 2

Fix the Door Cover trims (No.18

and No.19) to the Primary door

(Left side), Ensure the cover trims

are ush to the top and bottom of

the door. secure using 2x20mm

screws per cover trim.

Fix the Turn buttons (No.27)

above each door using 2x30mm

screws, Ensure the turn buttons

hold the door.

4x20mm Screws

2x30mm Screws

Pre drill

hole

20mm

screw

30mm

screw

27 27

P 7

Please retain product label and instructions for future reference

P 8

Step 20

Parts needed - No.12 QTY 1

- No.20 QTY 1

- No.26 QTY 2

Opening Window

Fixed Window

Pre drill

hole

16mm

screw

30mm

screw

30mm

Screws

16mm

screws

Opening Window

Place the Window Cover Trim

(No.20) 11mm over the window

opening and x in place with

3x30mm screws per strip.

3x30mm Screws

If you would like the window

(No.12) to be opening use the

butt hinges (No.26) to attach the

window to the Window cover trim.

Fix the hinges to the window

cover trim using 30mm screws and

16mm to t the hinges to the

window frame.

6x16mm Screws

6x30mm Screws

Fixed Window

If you would like the window

(No.12) to be xed instead of

opening, secure the window

to panel using 4x30mm screws

per window.

4x30mm Screws

Step 22

Parts needed - No.13 QTY 4

- No.17 QTY 2

- No.27 QTY 2

Step 21

Parts needed- No.33 QTY 1

Pre drill

hole

20mm

screw

Fix the casement stay (No.33)

to the window and then align

the xings to the window panel

framing. Ensure the casement

stay ts onto the xings when

closed before securing in

place.

6x20mm Screws

Fix the Door blocks (No.13) onto

the inside of the door, secure using

2x40mm screws going through the

front of the door boards and into

the block. Secure the turn button

(No.27) onto the door block

(No.13) using 1x30mm screw.

Fix the Door blocks (No.13) along

the central framing on the inside of

each door as shown in the diagram,

using 2x40mm screws through the

door cladding and into the block.

Fix the Door Beading strips (No.17)

to the door framing and secure

using 4x30mm screws per strip.

9x30mm Screws

6x40mm Screws Pre drill

hole

30mm

screw

40mm

screw

13 13

17 17

13 27

P 9

Please retain product label and instructions for future reference

P 8

Felt

tacks

Step 23

Parts needed- No.31 QTY 1

Cut the Felt (No.31) into 3 sheets at

4260mm. Lay onto roof as shown in

diagram ensuring there is a 50mm

overhang around the sides.

Apply the felt tacks with a 100mm

space per tack.

220xFelt tacks

HANDLE

WITH CARE

60mm

Bolts

Pre drill

hole

Step 24

Parts needed- No.32 QTY 1

Align the lock (No.32) to the door,

ensuring equal spacing between

the cover trims and across the

doors.

Measure and mark the holes of the

lock (No.32) and drill through the

boards and through the framing

and door blocks

Fix the lock onto the door using

8x60mm Carriage Bolts and Nuts

Step 25

Parts needed -No.21 QTY 7

-No.22 QTY 5

Fix the Cover trims (No.21 and

No.22) to the corners and across

each join of the building as shown,

secure to the buiding using

3x30mm screws per cover trim.

36x30mm Screws

Pre drill

hole

30mm

screw

22 22

21 21

22 22

21 21

Please retain product label and instructions for future reference

P 10

Step 26

Parts needed- No.23 QTY 4

-No.24 QTY 2

Fix the Fascias (No.23 and No.24)

to each side of the building,

ensuring they are ush to the top

of the building, secure using

3x40mm screws per fasica.

18x40mm Screws

Pre drill

hole

40mm

screw

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 03DTSHPN0806PA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04LEAN0804-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products SI-002-001-0022 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 10DTSHPN0804-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0409DSHPB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRO0705-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0608FGD4MW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Groundsman Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVPN0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX1006SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRO0705-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0510PB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02STRPCK1412-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03HEL1010DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0304SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01RAW1010DDOW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RASH0302FBSDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA0808FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01BEACH-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DDPENT1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTMBAX0103SD-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung