Mercia Garden Products 03DTSHPN1208FGC32TWSA-V1 Bedienungsanleitung

P 1

03DTSHPN1208FGC32TWSA-V1

DIP TREATED SHIPLAP PENT 12FT X 8FT FULLY GLAZED CONCENTINA 3 2 TALL WINDOW

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips

screwdriver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for

maintenance, annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree

causing damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of

heavy or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur

during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided

but can be helped. It is suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to

prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof

treatment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The

cladding should overlap the base, creating a run o for water. It is also recommended that the oor be at least

25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting

or using this product.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

P 2

03DTSHPN1208FGC32TWSA-V1

Please retain product label and instructions for future reference

14 15 16 17

234 5 6

78 9

21 22

Overall Dimensions:

Width = 3618mm

Depth = 2471mm

Height = 2162mm

Base Dimensions:

Width = 3517mm

Depth = 2395 mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Door Panel Back Panel

1170mmx1981mm

Short Panel

856mmX1776mm

Short Window

Panel

AI-03S22SHTCD2033X2025-V1

QTY 1

Internal Panel

1712mmX1760mm

Floor

Roof

Storage Door

Panel

Side Panel

1712mmX1776mm

Storage Door

Secondary Door

Master Door

AI-PRMFGMD600X1715-V1

Under Roof

Storage Gable Left

Veranda

Storage Floor Double Boarded Gable Top Gable Top Right Gable Top Left

Storage Gable Right

Floor Blocks - 27x44x400mm QTY 3

Cover Trim - 12x56x1980mm

QTY 2

Cover Trim - 12x56x2000mm

QTY 2

Cover Trim - 12x56x2011mm

QTY 1

Cover Trim - 12x56x2040mm

QTY 1

Cover Trim - 12x56x2070mm

QTY 1

Cover Trim - 12x56x2080mm

QTY 2

Side Fascia - 12x111x1228mm

QTY 4

Front Fascia - 12x111x1809mm

QTY 2

F2744-400mm

S12111-1809mm

Door Stop

QTY 1

Felt QTY 1

Press Lock QTY 1

Handle QTY 1

Barrel Bolt QTY 4

Door Handles QTY 2

Fixing Kit continues on P3

AI-S21SHPP1170X1981-V1

QTY 3

AI-S21SHPPTOV856X1776-V1

QTY 1

AI-03S21SH1TFWC856X1776-V1

QTY 1

Long Window

Panel

AI-03S21SH1TFWC594X2025-V1

QTY 1

AI-S21SHPPTOV1712X1760-V1

QTY 1

AI-S21MBF1753X1753-V1

AI-S21MBPR1198X2455-V1

AI-03S21SHSD827X2026-V1

QTY 1

AI-S21SHPPTOV1712X1776-V1

QTY 1

AI-03S21SHPGL571X2107-V1 AI-03S21SHPGR571X2107-V1

AI-S21MBURF1355X641-V1

QTY 2

AI-S21STVF1340X628-V1

QTY 2

AI-S21MBF825X614-V1 AI-S21SHDBPGT1712X320-V1 AI-S21SHPGTR1712X320-V1 AI-S21SHPGTL1712X320-V1

S12111-1228mm

S1256-1980mm

S1256-2000mm

S1256-2011mm

S1256-2040mm

S1256-2070mm

S1256-2080mm

QTY 2

QTY 3

AI-PRMFGSD600X1715-V1 AI-PRMFBMD600X1715-V1

PLY TRIANGLE

PI-07-0162

PI-07-0114

PI-07-0159

PI-07-0001

Door Trim - 16x60x1698mm

QTY 2

S1660-1698mm (rounded edge)

Press Lock Base-

28x28x95mm

QTY 2

F2828-95mm

Plain Door

AI-PRMFGPD600X1715-V1

Internal Panel Framing - 44x44x1905mm

QTY 1

F4444-1905mm

P 3

Please retain product label and instructions for future reference

Step 1

Parts needed - No. 11 QTY 2

Place oors (No. 11) on a rm and

level base, ensure base has suitable

drainage free from areas where standing

water can collect. (See front page on base

requirements). Fix the two oor panels

together as shown using 50mm screws at

an angle and alternate the positions.

10x50mm Screws

50mm

screw

Pre drill

hole

IMPORTANT: Pre-drill before xing screws.

*This building can be built with the shed on the LEFT hand side. Follow the

same steps but be aware to position panels to the opposite side.*

Secure the oor (No. 11) to the

Floor Blocks (No. 23) using 2x30mm

screws per Floor Block.

6x30mm Screws

Pre drill

hole

30mm

screw

Step 2

Parts Needed - No. 23 QTY 3

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

30mm

screw

Step 3

Parts Needed - No. 19 QTY 1

Secure the Storage Floor (No. 19) to the

assembly from Step 2, using 2x30mm

screws per Floor Block.

6x30mm Screws

IMPORTANT: Pre-drill before xing screws.

Butt Hinge QTY 12

Key Plate QTY 1

Turn Button QTY 4

Fixing kit cont..

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

PI-07-0066

PI-07-0017

PI-07-0034

Mortice Lock QTY 1

PI-07-0017

50mm Screw x 136

Felt Tacks x 150

30mm Screw x 139

10mm Screw x 16

70mm Screw x 9

*This building can be built with the shed on the

LEFT hand side. Follow the same steps but be

aware to position panels to the opposite side.*

Nail Bag

There may be extra screws present in the nail bag

40mm Screw x 8

25mm Screw x 18

P 4

Please retain product label and instructions for future reference

Step 4

Parts Needed - No. 3 QTY 1

- No. 4 QTY 1

Fix the side of the short panel (No. 4)

against the framing of the back panel (No. 3)

with 3x50mm screws as shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 5

Parts Needed - No. 2 QTY 1

Fix the side of the Short Panel (No. 4)

against the side of the Short Window Panel

(No. 2) with 4x50mm screws as shown in

diagram.

Do not secure the building to the Floor

until the roof is tted.

4x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws. Step 7

Parts Needed - No. 3 QTY 2

Fix the side of the Back Panel (No. 3)

against the side of the other Back Panel

with 4x50mm screws as shown in

diagram. Repeat this for the remaining

Back Panel.

Do not secure the building to the

Floor until the roof is tted.

8x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 6

Parts Needed - No. 6 QTY 1

Place the Long Window Panel (No. 6)

onto the assembly next to the Short

Window Panel (No. 2). Fix with 3x70mm

screws as shown in diagram externally.

Make sure that the Framing is ush with

other Framing, not the cladding.

Do not secure the building to the

Floor until the roof is tted.

3x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

P 5

Please retain product label and instructions for future reference

Step 8

Parts Needed - No. 1 QTY 1

Place the Door Panel (No. 1) onto the

assembly next to the Long Window Panel

(No. 6). Fix with 4x50mm screws as

shown in diagram internally.

Do not secure the building to the

Floor until the roof is tted.

4x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Pre drill

hole

70mm

screw

Step 9

Parts Needed - No. 5 QTY 1

- No. 33 QTY 1

Fix the side Internal Panel (No. 5) against the

framing of the Door Panel (No. 1) with 3x70mm

screws as shown in the diagram externally.

Make sure that the Framing is ush with other

Framing, not the cladding.

Then x the Internal Panel Framing (No. 33) to

the otherside of the Internal Panel (No. 5) with

3x50mm screws as shown in the diagram

internally.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

3x70mm Screws

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 10

Parts Needed - No. 21 QTY 1

- No. 22 QTY 1

Place the Gable Top Left/Right (No. 21/No. 22)

upon the top of the side panels, slotting

the groove of the boarding on the gable

into the tongue of the side panel as shown

and screw internally.

Fix with 4x50mm screws per gable top as

shown in diagram.

8x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

P 6

Please retain product label and instructions for future reference

Step 11

Fix the edge of the Internal Panel Framing

(No. 33) to the inside of the Back Panel

(No. 3) externally with 4x50mm screws as

shown in diagram.

Make sure that the panels are in a square

position and use the Gable Top Right

(No. 21) as a guide so that you x the

screws correctly in a straight line.

4x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 12

Parts Needed - No. 7 QTY 1

Fix the side of the Side Panel (No. 7)

against the framing of the Back

Panel (No. 3) with 3x 50mm screws

as shown in diagram.

Fix with 3x50mm screws as shown in

diagram.

Do not secure the building to the

Floor until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 13

Parts Needed - No. 20 QTY 1

Place the Double Boarded Gable Top (No. 20)

on top of the Side Panel (No. 7) slotting

the groove of the boarding on the gable

into the tongue of the side panel as shown.

Fix with 4x50mm screws per gable top as

shown in diagram.

4x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 14

Parts Needed - No. 13 QTY 1

- No. 14 QTY 1

Place the Storage Gable Sides Left/Right

(No. 13/14) against the sides of the

Internal (No. 5) and Side Panel (No. 7 )

with the boarding facing outwards as

shown.

Fix with 4x50mm screws per gable as

shown in diagram.

Do not secure the building to the

Floor until the roof is tted.

8x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Please retain product label and instructions for future reference

P 7

Pre drill

hole

30mm

screw

Step 16

Parts Needed - No. 15 QTY 1

- No. 16 QTY 1

- No. 42 QTY 6

Fix the master door (No.15) to the outside

of the door framing and secondary door

(No.16) to the attached plain doors with

3x butt hinges per door, using 6x30mm

screws per hinge.

*Ensure the doors open freely,

folding back into the building

unrestricted.

36x30mm Screws

IMPORTANT: Pre-drill before xing screws.

Step 17

Parts Needed - No. 32 QTY 2

- No. 37 QTY 2

- No. 40 QTY 4

- No. 41 QTY 1

- No. 43 QTY 1

Fit the mortice lock (No. 41) into the

recess and x in place with the screws

provided. Fit the key plate (No. 43) to the

opposite door using the 4X30mm screws

provided.

Fix door handles (No. 37) using 8x30mm

screws.

Fix the Door Trims (No. 32) to the

plain (No. 17) and secondary door (No. 16),

positioning the strip with a small overhang

to the right hand door. Fit the barrel bolts

(No. 40) to top and bottom of the door

strips as shown in diagram. Use 4x10mm

screws per barrel bolt.

Ensure doors open and close freely.

10x30mm Screws

16x10mm Screws

43 The Mortice Lock is Reversible

Pre drill

hole

IMPORTANT: Pre-drill before xing screws.

30mm

screw

10mm

screw

Step 15

Parts Needed - No. 17 QTY 1

- No. 42 QTY 3

Attach the Plain Door (No.17) to the

door panel using 3x butt hinges (No.42)

per door.

18x30mm Screws

Pre drill

hole

30mm

screw

IMPORTANT: Pre-drill before xing screws.

Please retain product label and instructions for future reference

P 8

Step 19

Parts Needed - No. 18 QTY 1

- No. 42 QTY 3

Secure the 3x hinge (No. 42) to the

storage door (No. 18) and the storage

door panel (No. 8).

Do not secure the building to the

Floor until the roof is tted.

18x25mm Screws

Pre drill

hole

25mm

screw

Storage Door hinges tted on the right

hand side of the door which means that

your door will open on the left side.

IMPORTANT: Pre-drill before xing screws. Step 21

Parts Needed - No. 10 QTY 2

Place the assembled Verandas (No. 10)

ush to the building as shown to make

sure the building is square.

Pre drill

hole

70mm

screw

Step 20

Parts Needed - No. 10 QTY 2

Lay the 2x Veranda (No. 10) face down,

side by side and x together with 3x70mm

screws through the bearers as shown in the

diagram, to secure the two Verandas

together.

3x70mm Screws

IMPORTANT: Pre-drill before xing screws.

Step 18

Parts Needed - No. 8 QTY 1

Place the Storage Door panel (No. 8)

against the end of the Storage Gable Sides

(No. 13/14) and x into position internally.

Fix with 4x50mm screws per side internally

as shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

8x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Please retain product label and instructions for future reference

P 9

Pre drill

hole

Step 22

Parts Needed - No. 9 QTY 3

Place the Roof Panels (No. 9) onto

the top of the building. Align the 3

Roof Panels so they sit square before

xing into position.

Do not secure the building to the

Floor until the roof is tted.

Step 23

Fix the three Roof panels together using

50mm oset from each other as shown

in the diagram.

Do not secure the building to the

Floor until the roof is tted.

16x50mm Screws

Pre drill

hole

50mm

screw

Step 25

Screw internally with 50mm screws

securing the roof panels (No. 9) x 3 to

all of the panels on the front and back

of the building.

Do not secure the building to the

Floor until the roof is tted.

*External panels not shown

16x50mm Screws

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Step 24

Parts Needed - No. 12 QTY 2

Place the Under Roof Panels (No. 12) into

position,making sure it is ush to the Door

panel and Storage section.

Fix in place making sure to screw

through the Roof framing.

14x30mm Screws

Pre drill

hole

30mm

screw

Please retain product label and instructions for future reference

P 10

HANDLE

WITH CARE

Step 27

Parts Needed - No. 35 QTY 1

Cut the Felt (No. 35) into 3 sheets at 3700mm

lengths each and lay onto the roof.

*Ensure there is approximately 50mm of

overhang around the building.

Fix into place using 150 x felt tacks at

100mm intervals.

150x Felt tacks

Felt

tacks

Step 26

Once the Roof is aligned and secure the

Floor can be xed into position.

Fix the building into place by screwing

through the panel into the oor making

sure to screw into the oor bearers.

*External panels not shown

37x50mm Screws

Pre drill

hole

50mm

screw

IMPORTANT: Pre-drill before xing screws.

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 0628CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTPOT0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04DTSTRDPN0804HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0608FGD4MW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DDPENT1408-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1610DDOW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0806SDSEC-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04GREEN0806SD-V6 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1010DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01TDM0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES1208-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1008DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG127-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 8x8 Helios Summerhouse Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products BOURNEMOUTH 03BRN0707-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0306DDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG209-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Groundsman Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DDPENT1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTODB0406-V1 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung