Mercia Garden Products 01SHPWOR1010DDOW-V1 Gebrauchsanweisung

N/A

Overlap

Cladding

Shiplap

Cladding

Solid Sheet

Roof

T&G Roof

Solid Sheet

Floor

T&G Floor

Fixed

Windows

Opening

Windows

For Assistance Please

Contact Customer Care on

01636 880514

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be erected by two

adults

For ease of assembly, you must pilot

drill all screw holes and ensure all

screw heads are countersunk.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand

(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,

step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather

conditions. For the duration of heavy or extended periods of rain, swelling of the

wood panels may occur. Warping of the wood may also occur during excessive

dry spells due to an interior moisture loss. Unfortunately, these processes cannot

be avoided but can be helped. It is suggested that the outdoor building is

sprayed with water during extended periods of warm sunshine and sheltered as

much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to

protect the product during transit and for upto 3 months against mould. To

validate your guarantee and ensure longevity of the product, it is ESSENTIAL the

building is treated with a wood preserver within the rst three months of

assembly and thereafter in accordance with the manufactures recommenda-

tions. Care must be taken to ensure the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Whilst all products manufactured are made to the

highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot

accept responsibility for your safety whilst erecting or

using this product.

Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces

of the timber. You are strongly advised

to wear gloves when working with or

handling rough sawn timer.

**Protim Fentex E5**

Biocidal Product Regulation (EU 528/2012) Article 58 Information

Protim Fentex E2 preserved wood is a “treated article”which incorporates biocidal products.

Wood correctly preserved with Protim Fentex E2 is protected against mould in storage.

Contains: IPBC (3-iodo-2-propynyl-N-butyl carbamate) and propiconazole.

Wear gloves when handling freshly treated wood.

Avoid breathing dust when cutting treated or untreated wood.

Dispose of o-cuts responsibly – do not burn.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer

to diagrams for the base dimensions, The base should be slightly smaller than

the external measurement of the building, i.e. The cladding should overlap the

base, creating a run o for water. It is also recommended that the oor be at

least 25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Please retain product label and instructions for future reference

P 1

General Instructions

Refer to the instructions pages for you specic product code

14/01/2014

01SHPWOR1010DDOW-V1

10x10 Shiplap Workshop with double doors, opening windows,T & G floor and roof.

12x10 Shiplap Workshop with double doors, opening windows,T & G floor and roof.

16x10 Shiplap Workshop with double doors, opening windows,T & G floor and roof.

20x10 Shiplap Workshop with double doors, opening windows,T & G floor and roof.

01SHPWOR1210DDOW-V1

01SHPWOR1610DDOW-V1

01SHPWOR2010DDOW-V1

H=220cm W=140cm L=130cm

30mm Black Screw x 12

P 2

01SHPWOR1010DDOW-V1

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Overall Dimensions:

Length = 3114mm

Width = 3179mm

Height = 2485mm

Base Dimensions:

Length = 3010mm

Width = 2980mm

Building content

13456

Plain Side

Qty 2

Window Side

Qty 2

Floor

Qty 4

Roof Panel

Qty 2

Front

Gable

Right

Front

Gable

Left

Front

Gable

Top

Back Gable

Right

Back Gable

Left

Truss Block - 160mm Qty 2

Door Gable Rail - 1332mm Qty 2

Tower Catch Block - 118mm Qty 2

Truss

Plain Gable Strip - 2387mm Qty 1

Cover Trim - 1757mm Qty 11

Finial

Qty 2

21 T Hinge

Qty 6

Felt

casement stay

QTY 2

Butt hinge QTY 4

Rim Lock

& Handle

Tower Bolt QTY 2

Master

Door

Slave

Door

Door Gable Strip - 2552mm

Cover Strip - 2800mm Qty 3

Gable Block - 342mm

Plain Gable Board

29 Window

QTY 2

Nail Bag 30mm Screw x 85

20mm Screw x 12

50mm Screw x 82

70mm Screw x 6

40mm Screw x 106

Felt Tacks x 170

16mm Screws x 12

100mm Screw x 2

Remove transportation

blocks from the bottom

of each panel before

beginning assembly. Each

Panel should have two

Pre Assembly

Door Gable Assembly

Step 1

2 x 50mm screws

Lay the Front Gable Right and Front Gable

top on a level floor place them next to each

other, ensure they are level at the top then

fix together using 2x50mm screws.Stagger

the screws so they do not collide.

50mm

screw

Pre drill

hole

P 3

Step 2

2 x 50mm screws

Lay the Front Gable Left next to the Front

Top Gable, ensure they are level at the top

then fix together using 2x50mm screws.

Stagger the screws so they do not collide.

50mm

screw

Pre drill

hole

Line the Door Gable Strip up to the

assembled gable at the corners as shown in

the illustration and fix in place using 40mm

screws.

5x40mm Screws

40mm

screw

Pre drill

hole

Plain Gable Assembly

Step 3

12 x 50mm screws

Lay the Back Left Gable and Back Right

Gable on a level floor place them next to

each other, ensure they are level at the top

and bottom then fix together using

10x50mm screws. Stagger the screws so

they do not collide.

50mm

screw

Pre drill

hole

Turn the gable section over

and secure the top board in

place using 3x30mm

screws. Ensure to screw into

the framing, pre-drilling to

avoind splitting the board.

3 x 30mm screws

50mm

screw

Pre drill

hole

P 4

32 x 40mm screws

Place floor on firm and level base, ensure

base has suitable drainage free from areas

where water can collect. (See front page on

base requirements).

Attach the floors using 32 x 40mm screws

40mm

screw

Pre drill

hole

Step 4

Do not secure the building to

the floor until the roof is fitted.

Fix the corners with 50mm

screws as shown in diagram.

Position the panels so there is equal spacing

between the floor and cladding on all 4 sides

Step 5

3x50mm Screws

50mm

screw

Pre drill

hole

Step 6

Fix the remaining window side

and the splain side at the

corner with 50mm screws as

shown in diagram.

6x50mm Screws

50mm

screw

Pre drill

hole

P 5

*Cut down trims to t

Measure the length of the door

gable rail and cut down a strip

match.

Fix in place using 2x30mm

screws.

Step 7

Fix the remaining plain side with

50mm screws as shown in diagram.

3x50mm Screws

50mm

screw

Pre drill

hole

Step 8

Fix the Door Gable (refer to steps 1

and 2 if you have not already

assembled this) at the corners with

50mm screws as shown in diagram.

6x50mm Screws

50mm

screw

Pre drill

hole

Step 9

Fit the Door Gable Rail between the

Front Gable Left and Right. Fix to the

floor using 3x50mm screws. Ensure

screws line up with the framing.

3x50mm Screws

50mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

70mm

screw

100mm

screw

*Cut down trims to t

Measure the height of the

doors and cut two trims to

match. Fix the strips onto the

gable using 6 x 30mm screws.

Measure across from the

edges of the strip and cut the

third strip to match.

Fix the T Hinges onto the

doors and door gable as

shown. Ensure that the screws

go through the cladding and

into the framing behind.

51x30mm screws

Step 10

30mm

screw

Pre drill

hole

Step 11

Place a Truss central to where two

panels join. Align the top of the

truss with the top of the sides as

shown in the diagram.

HINT - Use a piece from the xing

kit as a guide.

Pencil mark the truss position and

remove truss.

Place the truss blocks up to the

pencil mark and x using 2x70mm

screws per block.

Place the truss back into position on

top of the support block and secure

using 100mm screw each side from

the top down through the truss and

into the block.

4x70mm Screws

2x100mm Screws

Pre drill

hole

Pre drill

hole

P 7

Step 12 Step 13

Place a roof sheet ontop of the

plain gable and truss making sure

the roof sheet sits into the gables

and x using 40mm screws. Ensure

there is an equal amount of

overhang on either side of the roof.

12x40mm Screws

40mm

screw

Pre drill

hole

Place the second roof sheet

ontop of the truss and ensure

that it butts up to the one

already xed. Following the

same method outlined in step

12.

12x40mm Screws

40mm

screw

Pre drill

hole

P 8

Step 14 Step 16

Once the roof is fixed

attatch the building to the

floor with 50 mm screws.

36 x 50mm Screws

50mm

screw

Pre drill

hole

HANDLE

WITH CARE

170 x felt tacks

Cut four strips of felt and place

onto the roof. See below for

sizes.

Place the felt flat onto the roof

in the order that is stated on

the diagram below.

Once the sheets are laid out fix

them onto the roof with tacks

100mm apart.

Felt Strip Sizes

3210mm

Felt

tacks

BBBB

P 9

*Cut down trims to t

Step 17 Step 18

Fit the cover trims to the

building and secure in place

with 40mm screws as shown.

Fit the Plain Gable Strip

where the two back gables

join using 4x40mm screws.

Pre drill to avoid splitting.

28x40mm Screws

20 18

40mm

screw

Pre drill

hole

16x40mm Screws

Fit the fascias to the roof

over the felt and secure in

place with 40mm screws as

shown.

Pre drill to avoid splitting.

Measure and trim down to

size.

40mm

screw

Pre drill

hole

18 18

18 24

Attatch the tower bolts to

the top and bottom door

blocks with 6x30mm screw

for each one.

First line up the door blocks

on top of the framing of the

doors.Then fix with

2x50mm screws by screwing

through the matchboard

door into the block.

12x30mm Black Screws

4x50mm Screws

Step 19 Step 20

30mm

16mm

Opening Window

Fixed Window

30mm

screw

30mm

screw

16mm

screw

30mm

screw

Place the cover strip 11mm above the

window gap in the window panel and

fix with 3x30mm screws per strip.

Measure and trim before fitting.

If you would like the windows to be

opening use the butt hinges to

attach the opening window strip

and the opening window together.

Use 30mm screws to fix the butt

hinge to the Window Strip and

16mm screws to fix it to the

Opening Window.

If you want to fix the opening

windows, instead of fixing butt

hinges to the opening window,

use 4x30mm screws to attach

the opening windows to the

window panel as shown in the

diagram.

3x30mm Screws

*SCREW COUNT PER WINDOW

6x30mm Screws

6x16mm Screws

4x30mm Screws

*Cut down trims to t

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0406DDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0806SDSEC-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628PNNE0325HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03LBRO1008-V7 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Tulip Playhouse 02TUL411411-V4-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG016-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V6 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCV0808HGD4MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03HEL0808DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products CARLTON ARBOUR ESDXL21PT050 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products OIDTOVRA1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644CVNE0403HGDD3SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0306DDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVPN0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04VCGRO-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619RANE3503FGSD3TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG018-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01MODP0804-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHPN1208FGC32TWSA-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V2-PEFC Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung