Mercia Garden Products 0634LOG174-V4 Gebrauchsanweisung

P 1

0634LOG174-V4 (4.5x3.5m)

0634LOG174-V4: 4.5x3.5m reverse apex cabin (34mm)

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

BUILDING A BASE

When thinking about where the building and base are going to be constructed:

Ensure that there will be access (60cm) to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions. The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for your specic product code

For ease of assembly use a

rubber mallet to t the log

boards. Do NOT use a heavy

hammer.

Ensure to measure and check before cutting

boards.

It is advisable to use a hand

saw when cutting roof and

oor boards.

To ensure log boards are even, use a spirit

level to check each layer has been installed

correctly.

Felt

P 2

0634LOG174-V4

Overall Dimensions:

Width = 4536mm

Depth = 3651mm

Height = 2626mm

Base Dimensions:

Width = 4308mm

Depth = 3308mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Medium Window Pack*

QTY 4

Double Door Pack* Log 174 Gable - 3500mm

AI-0634LOG174G-V4

QTY 2

Log Board - 34x120x3500mm QTY 8

LB34-A-3500

Log Board - 34x120x1465mm QTY 8

LB34-B-1465

Log Board - 34x120x357mm QTY 28

LB34-B-357

Log Board - 34x120x357mm QTY 28

LB34-C-357

Log Board - 34x120x4500mm QTY 19

LB34-A-4500

Log Board - 34x120x916mm QTY 28

LB34-B-916

Log Board - 34x120x1832mm QTY 28

LB34-B-1832

Roof Board - 16x121x1862mm QTY 82

MB16-1862

Floor Board - 16x121x3238mm QTY 38

MB16-3238

16 Bearer - 44x58x2038mm QTY 26

F4458-2038-PT

17 Bearer - 44x58x3308mm QTY 4

F4458-3308-PT

Purlin - 45x120x4504mm QTY 5

F45120-A-4504

Fascia - 16x120x1866mm QTY 4

S16120-1866 (Angled)

Fascia - 16x120x2268mm QTY 4

S16120-2268

21 Eaves Frame - 27x44x2250mm QTY 4

F2744-2250

4Starter Board - 34x66x4500mm QTY 2

LB34RT66-A-4500

Log Board - 34x120x3500mm QTY 2

LB34-AD-3500

Log Board - 34x120x4500mm QTY 1

LB34-AD-4500

*All components for the Windows and Doors

are shown in the Windows and Doors

instruction packs.

Roof Spacers QTY 5

PI-07-0208 (20x100x2mm)

Storm Brace - 27x44x2000mm QTY 8

F2744-2000

23 Closure Trim - 16x28x2400mm (approx length) QTY 15

SI628-2400 (Bevelled)

Felt Tacks x600

70mm Screw x80

Pre-assembly

*Please note:

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are tted properly in their respective

tongues and grooves.

Nail Bag

40mm Screw x700

30mm Screw x 78

P 3

Please retain product label and instructions for future reference

80mm Bolt Set x16

Pre drill

hole

70mm

screw

Following the same method

arrange the

remaining framing (No. 16)

inside the assembled frame.

*Ensure there is an equal

amount of space between

each frame.

Secure each of the frames in

place using 2x70mm screws

for each side of the bearer,

ensuring the framing remains

level.

44x70mm Screws

Example picture

2 screws per bearer per end.

P 4

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

Step 2

Parts needed- No. 16 QTY 11

Pre drill

hole

70mm

screw

Step 1

Parts needed - No. 16 QTY 2

No. 17 QTY 2

Lay the bearers (No’s 16 &

17) onto a rm and level surface

(free from areas where standing

water can collect ) as shown in

the illustration.

Fix the framing together at each

corner using 8x70mm screws,

ensuring the frame is ush.

*Ensure the 58mm side of the

bearer is laying on the base so

that you can screw the bearers

together on the 44mm side.

8x70mm Screws

1616

161616

Pre drill

hole

P 5

Please retain product label and instructions for future reference

70mm

screw

Step 3 (See Pre-Assembly)

Parts needed - No. 4 QTY 2

No. 5 QTY 2

Place the boards (No’s. 4 & 5) on

to the assembled base frame

along the longest

sides.

*Ensure the notches at either

end of each board are ush

and level with the ends of the

frame.

Fix each of the starter boards to

the frame by screwing through

the notch into the frame as

shown in the illustration.

4x70mm Screws

Step 4 (See Pre-Assembly)

Parts needed - No. 5 QTY 6

No. 7 QTY 8

No. 10 QTY 4

Following the same method

outlined in Pre-Assembly, lay

the rst 6 boards (No’s. 5, 7 &

10) onto the starter boards to

create your rst level.

*Ensure that the boards are

level and ush with each other

as you lay each one.

IMPORTANT: Pre-drill before xing screws. IMPORTANT: Pre-drill before xing screws.

Step 5

Once you have laid 6 log boards (o

of the starter) up the door section,

slide the assembled door frame (No.

2) over the boards resting the frame

on top of the starter board.

*Please note: This image is for

illustrative purposes and may dier

from your choice in product (regard-

ing door position). Nevertheless the

process of tting the door frame is

the same.

**Please Note: The short boards at

the

front of the building (either side of

the door and window opening’s) can

be placed either side depending on

your needs.

P 6

Please retain product label and instructions for future reference

Step 7

Once you have laid the second

level of boards onto the assembly

slide the window(s) (No. 1) between the

smaller boards and rest on to the

longer board.

*Ensure the boards are level with

each end.

*Please note: This image is for

illustrative purposes and may

dier from your choice in product

(regarding window position).

Nevertheless the process of tting

the window is the same.

IMPORTANT: Pre-drill before xing screws.

Step 6 (See Pre-Assembly)

Parts needed - No. 8 QTY 12

No. 9 QTY 12

No. 10 QTY 6

No. 12 QTY 12

No.13 QTY 12

Following the same method

outlined in Pre-Assembly, lay

the next 6 boards (No’s. 8, 9,

10, 12 & 13) onto the assem-

bly to create your second

level.

*Ensure that the boards are

level and ush with each

other as you lay each one.

**Doors can be hung once

the boarding has enclosed

the door frame.

*Doors can be hung once the

boarding has enclosed the

door frame by 12-13 boards,

refer to door installation

instructions, if not, you can

install the door at step 8.

***Please Note: The short boards placed

to create the opening’s for the doors &

windows can be placed either side

depending on your needs.

12 8

P 7

Please retain product label and instructions for future reference

12 8

Step 9 (See Pre-Assembly)

Parts needed - No. 6 QTY 2

No.10 QTY 2

No. 11 QTY 1

Following the same method

outlined in Pre-Assembly, lay

the last two boards (No. 6 &

10)and the board to go above

the door (No. 11) onto the

assembly.

*Ensure that the boards are

level and ush with each

other as you lay each one.

Step 8 (See Pre-Assembly)

Parts needed - No. 8 QTY 12

No. 9 QTY 12

No. 10 QTY 6

No. 12 QTY 12

No. 13 QTY 6

Following the same method

outlined in Pre-Assembly, lay

the remaining boards (No’s. 8,

9, 10, 12 & 13) onto the

assembly to bring the board

level to the top of the window

and door frames.

*Ensure that the boards are

level and ush with each

other as you lay each one.

*Doors can be hung once the

boarding has enclosed the

door frame.

Step 10 (See Pre-Assembly)

Parts needed - No. 3 QTY 2

Place the gable tops onto the

assembly. Fix into position by

screwing through the notches

as shown in the illustration.

*Ensure that the boards are

level and ush with each

other as you lay each one.

4x70mm Screws

Pre drill

hole

70mm

screw

IMPORTANT: Pre-drill before xing screws.

P 8

Please retain product label and instructions for future reference

Pre drill

hole

Step 11

Parts needed - No. 18 QTY 5

Align the Purlin(s) (No. 18)

into the cut out slots on each gable

top ensuring each purlin

interlocks the boards.

Secure the Purlins at each

end by screwing through the bars

into the boards (ensure to pre-drill

to avoid the boards splitting) using

4x70mm screws per purlin.

*Please note: The gable shown is

for

illustrative purposes and may dier

in width from your choice in

product.

Nevertheless, despite any

dierences

the process of xing the purlins

is the same.

20x70mm Screws

70mm

screw

Step 12

Parts needed - No. 14 QTY 82

Place the rst two roof board’s

(No. 14) onto the assembly on

each side, making sure the boards

are ush to the end of the roof

purlin. Once in position x to each

purlin using 4x40mm screws.

Due to natural occurences of wood

shrinkage / expansion. You maybe

required to use the provided spacers and

place a space of 2mm to ensure every roof

board lines up with the truss’.

*Ensure the roof boards meet

at the top of the apex and leave

an overhang at the bottom.

Continue adding the roof boards

along the roof, xing each one into

position using 4x40mm screws,

making sure that each board is

interlocked, ush at the bottom &

meet at the top of the apex.

The last board on each

side will overhang: Using a

straight edge and a pencil mark

out a line as a guide.

Cut along the pencil mark and

remove the excess. Place the

cut down board’s back onto the

roof and secure into place

using 4x40mm screws per

board.

*Please Note: This image is for illustrative

purposes and may dier from your choice

product. Nevertheless the process of

cutting

and tting the last roof boards is the

same.

328x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

IMPORTANT: Pre-drill before xing screws.

23b 14

IMPORTANT: Pre-drill before xing screws.

P 9

Please retain product label and instructions for future reference

Step 13

Parts needed - No. 21 QTY 4

Ensuring the roof boards are

ush at the overhanging side

and meet at the apex, x the

Eaves Frames (No. 21) to the

underside of the roof boards

using 9x40mm screws as shown

in the illustration.

*Please Note: This image is for

illustrative purposes and may

dier from your choice in

product. Nevertheless the

process of xing the eaves

frames is the same.

36x40mm Screws

40mm

screw

Pre drill

hole

Step 14

Parts needed - No. 15 QTY 38

Place the rst Floor Board (No. 15)

inside the building ush to the log

board on one side. Continue adding

the oor boards (internally) making

sure to interlock each individual

board.

*Do NOT secure the boards until

the last board has been measured

and cut.

Following the same method outlined

previously measure the gap between

the bottom of the tongue (on the last

board placed) and the log board.

Using a straight edge mark out the

measurement onto the last oor

board (No. 15) and cut along the

length removing the excess.

**Please note: Mark the nal board

2mm under the measurement; This

will allow the timber to expand and

contract correctly.

Once all the oor boards are in

position secure each board into

position using 8x40mm screws.

***Please Note: Ensure to screw

through each of the oor boards

into the oor bearers.

304x40mm Screws

40mm

screw

Pre drill

hole

*Cut to t

P 10

Please retain product label and instructions for future reference

Felt tacks

Step 17

Parts needed - No. 24

Cut the felt (No. 24) into ve strips &

lay onto the roof in the order shown

in the illustration.

*Ensure there is approximately

50mm of overhanging felt each

side.

Once the felt is laid out x to the

roof using felt tacks at 100mm

intervals.

*Felt size: 5132mm

416x Felt Tacks

HANDLE

WITH CARE

1. 2.

3. 4.

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Roof

Closure Trim

Internal

*Measure and cut the

closure trims to

t the internal space.

Pre drill

hole

30mm

screw

*trim to t

Step 15

Parts needed - No. 23 QTY 6

Inside the building place the closure

trim (No. 23) against the boarding

and align with the roof as shown in

the illustration.

Once in position x each trim

into place by pre drilling a pilot hole

and using 6x30mm screws per trim,

equally spacing them along the face

of the board.

36x30mm Screws

30mm

screw

Pre drill

hole

*Cut to t

Step 16

Parts needed - No. 23 QTY 7

Once the oor has been laid arrange the

closure trim (No. 23) around the outside

edge of oor (internally), measure and cut

down accordingly to best match the

internal space.

Secure each trim section into place using

6x30mm spaced equally along the board

as shown in the illustration.

*Do NOT x the closure trim to the oor

boards.

42x30mm Screws

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB0808DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products ESDXL21PT001 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 06LOG171SG-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBA0705SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634CSNE0404HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0909FGD4TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG018-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1010DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619WKNE2633LBDD1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG131-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Tulip Playhouse 02TUL411411-V4-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RANE0504FGDD2TW1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02HON51156-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 06LOG002-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0608FGD4MW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03COR0707-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02GARA0806-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1408DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL1008DDFW-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 2DTSHDB0606SFD5W-V1-PEFC Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPP0705SDFW-V1 Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung