Metra Electronics 99-3309B Bedienungsanleitung

APPLICATIONS

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

Installation instructions for 99-3309B

• ISODINradioprovisionwithpocket

• DoubleDINradioprovision

• InterfaceincludedretainsfactoryOnStar,Bluetooth,and

allwarningchimes

• Providesa12-voltaccessorypowerandVSS,parking

brake,andreversesignals

• Painted matte black

•A)Radiotrimpanel•B)Radiobrackets•C)Pocket•D)(4)#8x3/8”Phillipsscrews•E)(10)Whiteplastic

panelclips•F)Interface•G)16-pinharness•H)4-pinto4-pinresistorpad•I)22-pinto44-pinharness

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS(soldseparately)

WiringHarness:

• Interfaceincluded

AntennaAdapter:

• 40-EU55

• Panelremovaltool•Phillipsscrewdriver

• Smallflat-bladescrewdriver

TOOLS REQUIRED

Chevrolet Spark 2013-up

99-3309B

See application list inside

A B C

F G H I

D E

99-3309B Dash Disassembly 99-3309B

1. Unclipandremovetheradio

trimpanel.(FigureA)

2. Remove(4)Phillipsscrews

securingthefactoryradio

andremovefromdash.

(FigureB)

3. Unclipandremovethevents

fromthefactorypanel.

(FigureC)

4. Unclipandremovethe

hazardbuttonfromthetrim

panel.(FigureC)

5. Remove(5)Phillipsscrews

securingtheupperdisplay

shroudfromthefactory

panel.(FigureC)

Continue to kit assembly

(Figure A) (Figure B)

Chevrolet Spark 2013-up

(Figure B)

Step 3

Step 5

Step 4

Step 5

Kit Assembly 99-3309B

ISO DIN radio provision with pocket

1. Attachthefactoryventsandhazard

buttontotheMetratrimpanel.

(FigureA)

2. Attachtheupperdisplayshroudthe

Metratrimpanelwiththefactory

screws.(FigureA)

3. Attachtheprovided(10)panelclipsto

thelegsoftheMetratrimpanel.

4. Locatethefactorywiringharnessin

thedash.Metrarecommendsusing

thepropermatingadapterfromMetra

orAXXESS.Re-connectthenegative

batteryterminalandtesttheunitfor

properoperation.

5. Attachtheradiobracketstothe

aftermarketradiousingthescrews

suppliedwiththeradio,thensecurethe

assemblytothepocketusingthe(4)

#8x3/8”Phillipsscrews.(FigureB)

6. Mounttheassemblyintothesub-dash.

7. Reassembledashinreverseorderof

disassemblyusingtheMetratrimpanel

insteadofthefactorytrimpanel. (Figure B)

(Figure A)

Step 2

Step 1

Step 2

Kit Assembly 99-3309B

Double DIN radio provision

1. Attachthefactoryventsandhazard

buttontotheMetratrimpanel.

(FigureA)

2. Attachtheupperdisplayshroudthe

Metratrimpanelwiththefactory

screws.(FigureA)

3. Attachtheprovided(10)panelclipsto

thelegsoftheMetratrimpanel.

4. Locatethefactorywiringharnessin

thedash.Metrarecommendsusing

thepropermatingadapterfromMetra

orAXXESS.Re-connectthenegative

batteryterminalandtesttheunitfor

properoperation.

5. Attachtheradiobracketstothe

aftermarketradiousingthescrews

suppliedwiththeradio,thenmountthe

assemblyintothesubdash.(FigureB)

6. Reassembledashinreverseorderof

disassemblyusingtheMetratrimpanel

insteadofthefactorytrimpanel. (Figure B)

(Figure A)

Step 2

Step 1

Step 2

99-3309B

Axxess Interface

Installation From the 16-pin harness:

• ConnecttheRedwirestotheignition/accessory

wireoftheaftermarketradio.

• ConnecttheOrange/Whitewiretothe

illuminationwireoftheaftermarketradio.Ifthe

aftermarketradiohasnoilluminationwire,tapeoff

theOrange/Whitewire.

• ConnecttheBlue/Whitewiretotheampturnon

wireoftheaftermarketradio.

• ConnecttheBrownwiretothemutewireofthe

aftermarketradio.Iftheaftermarketradiodoesnot

haveaMutewire,tapeuptheBrownwire.

• ConnecttheWhitewiretotheleftfrontpositive

speakeroutputoftheaftermarketradio.

• ConnecttheWhite/Blackwiretotheleftfront

negativespeakeroutputoftheaftermarketradio.

• ConnecttheGraywiretotherightfrontpositive

speakeroutputoftheaftermarketradio.

• ConnecttheGray/Blackwiretotherightfront

negativespeakeroutputoftheaftermarketradio.

• TheVioletwireisnotusedintheapplication.

• TheViolet/Blackwireisnotusedintheapplication.

• TheGreenwireisnotusedintheapplication.

• TheGreen/Blackwireisnotusedin

thisapplication.

Thefollowingwiresarefortheaftermarketradiosthat

havenavigationbuiltin:

• ConnecttheLight Greenwiretotheparkingbrake

wireoftheaftermarketnavigationradio.

• ConnecttheBlue/PinkwiretotheVSSorspeed

sensewireoftheaftermarketnavigationradio.

• ConnecttheGreen/Purplewiretothereversewire

oftheaftermarketnavigationradio.

From the 44-way harness:

• ConnecttheBlackwiretothegroundwireofthe

aftermarketradio.

• ConnecttheRCA’stotheAUXinontheaftermarket

radio(ifequipped).

Note: This will allow you to retain the 3.5 AUX JACK

in the console.

• ConnecttheYellowwiretothe12-voltconstant

wireoftheaftermarketradio.

• Ifthevehicleisamplifieddisconnectthe4-pin

harnesslocatedbetweenthe44-wayand22-way

connectorandconnectthesupplied4-pinto4-pin

resistorpad.

•Cuttingtool•Crimpingtool•Tape•Connectors

(butt-connectors,bellcaps,etc.)

TOOLS REQUIRED

•4-pinto4-pinresistorpadharness•16-pinwith

strippedleads•22-pinto44-pinCamaroHarness

•18-pinto10-pinHVACHarness

INTERFACE COMPONENTS

FEATURES

• Providesaccessory(12-volt10-amp)

• RetainsR.A.P.(RetainedAccessoryPower)

• Usedinamplifiedornon-amplifiedsystems

• Retainsallwarningchimes

• ProvidesNAVoutputs(parkingbrake,reverse,

mute,andV.S.S.)

• RetainsOnStar/OEBluetooth

• AdjustablevolumeforchimesandOnStar

• Highlevelspeakerinput

• Micro“B”USBupdatable

• Retainsbalanceandfade

Installing the interface

99-3309B

Installing the interface

Amplified vehicles:

• ConnecttheVioletwiretotherightrearpositive

wireoftheaftermarketradio.

• ConnecttheViolet/Blackwiretotherightrear

negativewireoftheaftermarketradio.

• ConnecttheGreenwiretotheleftrearpositivewire

oftheaftermarketradio.

• ConnecttheGreen/Blackwiretotheleftrear

negativewireoftheaftermarketradio.

Non-amplified vehicles:

• CuttheresistorsfromtheGreen, Green/black,

Purple, Purple/Blackrightbelowtheheatshrink.

• ConnecttheVioletwiretotherightrearpositive

wireoftheaftermarketradio.

• ConnecttheViolet/Blackwiretotherightrear

negativewireoftheaftermarketradio.

• ConnecttheGreenwiretotheleftrearpositivewire

oftheaftermarketradio.

• ConnecttheGreen/Blackwiretotheleftrear

negativewireoftheaftermarketradio.

• ThePinkwireisnotusedinthisapplication.

Installing the interface:

1. Withalltheconnectionscompleted,plugthe16and

22pinharnessesintotheinterface.

2. Plugthe44pinGMharnessintothevehicleside

harness,andplugtheaftermarketradioharnessinto

theaftermarketradio.

3. Reconnectthenegativebatteryterminal.

Initializing the interface

Attention: If the interface loses power for any

reason, the following steps will need to be

performed again.

• Initializetheinterfacebyturningtheignitiononfor

30seconds,thenturntheignitionbackoff,then

backonagain.

Note: If using the ASWC-1, connect it after

you initialize the interface, with the key in the

off position.

Chime volume adjustment

1) Withcaron,shutoffcarandleavekeysin

ignition.Openthecardoorandleaveitopen.

Chimeswillbeheard.

2) Wait10seconds,thenwithasmall

screwdriveradjustthepotentiometerfully

counterclockwise(allthewayleft),thenclockwise

toraisechimelevelandcounterclockwisetolower

thechimelevel.

3) Whenthevolumeisatthedesiredlevel,remove

thekeysfromtheignition.Thiswilllockthechime

volumeatitscurrentlevel.

Audio level adjustment

1) Startyourvehicleandturnontheradiohaving

audioplaying.

2) Turnyouraftermarketradio’svolumeup¾oftheway.

3) Withasmallscrewdriveradjustthepotentiometer

clockwisetoraisetheaudioleveland

counterclockwisetolowertheaudiolevel.

4) Onceatdesiredlevelyouraudioadjustment

iscomplete.

99-3309B

The OEM radio is used to customize certain features of the vehicle.

UsetheoptionalLCDtoadjustthesefeaturesaccordingly:

1. PressESC,andthenpressENT:“SetLanguage”willappearonthescreen.

2. Tochangethelanguage,pressENT,andthenpressthearrowupanddown

buttonstochangethelanguage.

3. Onceyouhaveselectedyourlanguage,press ESC togobacktothe

mainscreen.

4. Ifyoudonotwishtochangethelanguage,youcanscrollupanddownthrough

thedifferentsettingswiththearrowupanddownbuttons.

Note: What these options are depends on the vehicle/trim-level it is

installed into.

5. Remembertopress ENTtochangethedesiredsetting.

Vehicle customization

with optional LCD

(AXXESSpart#XIA-LCDsoldseparately)

OnStar level adjustment

ToadjusttheOnStarvolumelevelfindtheBlack/Yellowwireonthe16-pin

harness.PushtheblueOnStarbutton,whilethevoiceisspeakingtapthe 

Black/Yellowwiretoground.Oncethevolumeissetitwillstayatthatvolume

untiltheBlack/Yellowwireistappedtogroundagain.Thiscanbesetduring

installationandthenleftalone.Ifuseradjustmentisdesired,thecustomermay

alsotap“VolumeUp”ordownonthesteeringwheel(ifequipped)toadjustthe

OnStarlevel.

Additional 12-pin harness (ASWC-1)

• This12-pinharnessistobeusedinconjunctionwiththeASWC-1

(notincluded).PleaserefertotheASWC-1instructionsforprogramming.

Inhaltsverzeichnis

Andere Metra Electronics Autozubehör Handbücher

Metra Electronics

Metra Electronics 99-5838CH Bedienungsanleitung

Metra Electronics

Metra Electronics 99-6511 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7356B Bedienungsanleitung

Metra Electronics

Metra Electronics 99-8712 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-9303 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-7313 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7390B Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7335S Bedienungsanleitung

Metra Electronics

Metra Electronics 95-8223 Bedienungsanleitung

Metra Electronics

Metra Electronics CHTO-01 Bedienungsanleitung

Metra Electronics

Metra Electronics AW-333GM Bedienungsanleitung

Metra Electronics

Metra Electronics AFDI-RSE-01 Bedienungsanleitung

Metra Electronics

Metra Electronics 70-1722 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-3042 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-3528 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-7418 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-9616B Bedienungsanleitung

Metra Electronics

Metra Electronics 99-9100 Bedienungsanleitung

Metra Electronics

Metra Electronics LEXUS 99-8156 Bedienungsanleitung

Metra Electronics

Metra Electronics 71-6522 Bedienungsanleitung

Metra Electronics

Metra Electronics XIAH-FD4 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-8208 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7804B Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7954 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung