Metra Electronics 99-7604 Bedienungsanleitung
INSTALLATION INSTRUCTIONS FOR PART 99-7604
KIT FEATURES
•DIN Radio Provision
•ISO Mount Radio Provision
•Double DIN Radio Provision
•Stacked ISO Mount Units Provision
•Painted To Match Factory Dash
99-7604= SILVER
99-7604B= BLACK
99-7604T=TAN
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Pocket • E) Double DIN Brackets
•F) Double DIN Trim Plate • G) Top Radio Housing Bracket • H) (2) #8 X 3/8” Phillip Screws
•I) Climate Control Cable
KIT COMPONENTS
A
Hook Tool • Panel Removal Tool • (2) Small Flat Blade Screwdrivers
•Phillips Screwdriver • Socket set
1-800-221-0932
©COPYRIGHT 2008 METRA ELECTRONICS CORPORATION
www.metraonline.com
TOOLS REQUIRED:
APPLICATIONS
INFINITI G35
2003-2004
B
D
EG
C
F
I
H
99-7604/99-7604B/
99-7604T
Dash Disassembly
-INFINITIG352003-2004 .......................................1,2,3
Kit Preparation ................................................4
Kit Assembly
-DIN RadioProvisionwithPocket ..................................5
-ISO Mount Radio Provision with Pocket . . . . .........................6
-DoubleDIN RadioProvision.......................................7
-StackedISOUnitsProvision ......................................8
Final Assembly ..........................................9
TABLE OF CONTENTS
99-7604
*Note:
Refer also to the instructions included with the aftermarket radio.
K
NOWLEDGE IS
P
OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.
99-7604 DASH DISASSEMBLY
INFINITI G35 2003-2004
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip the collar below the shift knob
and slide down. Using a small screw-
driver or hook tool remove the spring
clip to release and remove the shift
knob.
(Figure A)
2
3
Continue on page 2 .
2
3
1
Unclip the cup holder/shifter trim
panel. Unplug and remove panel.
(Figure B)
4
Remove (2) Phillips screws from the
bottom of the radio/climate control
panel.
(Figure C)
5
Remove (2) Phillips screws from the
panel below the steering column then
unclip and let the panel hang.
A
B
C
D
E
6
Remove (2) Phillips screws from the
accessory plug panel then unclip and
remove the panel.
(Figure D)
Unclip and remove the passenger side
kick panel then remove (1) Phillips
screw exposed behind the panel on
bottom right side of glove box.
(Figure E)
7
99-7604 DASH DISASSEMBLY
INFINITI G35 2003-2004
2
Remove (2) Phillips screws from the
accessory plug panel then unclip and
remove the panel.
(Figure G)
10
Unclip and remove the trim panel sur-
rounding the clockand display on top
of the dash.
(Figure H)
11
12
Continue on page 3.
Remove (2) Phillips screws securing
the clock and clock bracket. Unplug
and remove clockand bracket.
(Figure I) H
F
G
I
J
8
Open glove box and remove (4)
Phillips screws from the top edge of
box opening.
(Figure F)
9
Unclip and remove the black cover
panel below glove box and remove (1)
Phillips screw from bottom of glove
box exposed on left side next to
accessory plug panel.
13
Remove (1) Phillips screw at the top
of the radio/climate control panel.
(Figure J)
99-7604 DASH DISASSEMBLY
INFINITI G35 2003-2004
3
Remove (2) Phillips screws securing
the pocket to the radio/climate con-
trol panel and remove pocket. (Retain
pocket for use during kit assembly.)
16
Use (2) small flat blade screwdrivers
to gently prythe vents from radio/cli-
mate control panel to remove.(Retain
vents for use during kit assembly.)
17
Unclip and remove the thin plastic
trim at the top edge of the radio/cli-
mate control panel.
18
Continue to kit preparation.
K
14
Unsnap radio/climate control panel
including climate control vents at the
top left and right and pocket assem-
bly.Unplug and remove panel.
(Figure K)
15
Remove (6) Phillips screws securing
the radio chassis to the factory panel
and remove radio chassis to access
the factory pocket.
4
99-7604 KIT PREPARATION
B
C
A
KIT PREPARATION
Attach the vents into the radio housing
in the same location as the factory
panel.
(Figure A)
1
Secure the factory pocket removed in
step 16 of the dash disassembly into
the radio housing using the factory
hardware.
(Figure B)
2
Continue to kit assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Attach the top radio housing bracket to
the radio housing using the (2) #8 X
3/8” Phillips screws provided with this
kit.
(Figure C)
3
Clip the thin plastic trim removed in
step18 (of page 3) to the top edge of
the radio housing.
4
Connect the blackend of the climate
control cable to the climate controls in
the radio housing and connect the
other end of the cable to the factory
climate control harness during final
assembly.
5
5
99-7604 KIT ASSEMBLY
B
C
A
DIN RADIO PROVISION WITH POCKET
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Snap the pocket into the radio housing.
(Figure C)
3
6
99-7604 KIT ASSEMBLY
B
A
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radio
with the screws supplied with the
radio.
(Figure A)
1
Slide the radio into the radio housing
until it snaps into place.
(Figure B)
2
Snap the ISO trim plate onto the front
of the Radio Housing.
(Figure B)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Snap the pocket into the radio housing.
(Figure C)
4
C
7
99-7604 KIT ASSEMBLY
B
C
A
DOUBLE DIN RADIO PROVISION
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
1
Slide the Double DIN radio into the
bracket/trim plate assembly and
secure the radio to the assembly using
the screws supplied with the radio.
(Figure C)
3
Snap the Double DIN trim plate into the
radio housing.
(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Cut and remove the center bar from
the radio housing.
(Figure A)
8
99-7604 KIT ASSEMBLY
B
C
A
STACKED ISO UNITS PROVISION
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the stacked ISO units into the
bracket/radio housing assembly and
secure the units to the kit using the
screws supplied with the units.
(Figure C)
3
Snap the Double DIN trim plate into the
radio housing.
(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
1
Cut and remove the center bar from
the radio housing.
(Figure A)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Metra Electronics Autozubehör Handbücher
Metra Electronics
Metra Electronics 99-6520B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7424 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7340B Bedienungsanleitung
Metra Electronics
Metra Electronics 70-7003 Service-Handbuch
Metra Electronics
Metra Electronics 99-1003 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-5801 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-5808 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-5838CH Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8214TB Bedienungsanleitung
Metra Electronics
Metra Electronics 88-00-3302 Bedienungsanleitung
Metra Electronics
Metra Electronics 98-5999 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8201 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7810B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-6505 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-5817 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-3023HG Bedienungsanleitung
Metra Electronics
Metra Electronics 95-6511 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8100 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7008 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7011 Bedienungsanleitung
