Mitsubishi Electric 700 Series Bedienungsanleitung

INSTRUCTION MANUAL

INVERTER

Plug-in option

FR-A7AX

FR-A7AX E kit

16-bit digital input function INSTALLATION AND WIRING

(FR-A700/F700 SERIES)

INSTALLATION AND WIRING

(FR-E700 SERIES (E kit))

CONNECTION DIAGRAM AND TERMINAL

PARAMETERS

PRE-OPERATION INSTRUCTIONS

A-1

Thank you for choosing this Mitsubishi Inverter plug-in option.

This instruction manual gives handling information and

precautions for use of this equipment. Incorrect handling might

cause an unexpected fault. Before using the equipment, please

read this manual carefully to use the equipment to its optimum.

Please forward this manual to the end user.

1. Electric Shock Prevention

This section is specifically about

safety matters

Do not attempt to install, operate, maintain or inspect this

product until you have read through this instruction manual and

appended documents carefully and can use the equipment

correctly. Do not use this product until you have a full

knowledge of the equipment, safety information and

instructions.

In this instruction manual, the safety instruction levels are

classified into "WARNING" and "CAUTION".

Assumes that incorrect handling may

cause hazardous conditions, resulting

in death or severe injury.

Assumes that incorrect handling may

cause hazardous conditions, resulting

in medium or slight injury, or may

cause physical damage only.

Note that even the level may lead to a serious

consequence according to conditions. Please follow the

instructions of both levels because they are important to

personal safety.

WARNING

CAUTION

SAFETY INSTRUCTIONS

WARNING

•While power is ON or when the inverter is running, do not

open the front cover. You may get an electric shock.

•Do not run the inverter with the front cover or wiring cover

removed. Otherwise, you may access the exposed high-

voltage terminals and charging part and get an electric shock.

•If power is OFF, do not remove the front cover except for

wiring or periodic inspection. You may access the charged

inverter circuits and get an electric shock.

•Before starting wiring or inspection, check to make sure that

the indication of the inverter operation panel is OFF, wait for at

least 10 minutes after the power supply has been switched

OFF, and check that there are no residual voltage using a tester

or the like. The capacitor is charged with high voltage for some

time after power OFF and it is dangerous.

•Any person who is involved in the wiring or inspection of this

equipment should be fully competent to do the work.

•Always install the plug-in option before wiring. Otherwise,

you may get an electric shock or be injured.

•Do not touch the plug-in option with wet hands. Otherwise

you may get an electric shock.

•Do not subject the cables to scratches, excessive stress,

heavy loads or pinching. Otherwise you may get an electric

shock.

A-2

2. Injury Prevention

3. Additional Instructions

Also note the following points to prevent an accidental failure,

injury, electric shock, etc.

1) Transportation and mounting

2) Trial run

3) Usage

4) Maintenance, inspection and parts replacement

5) Disposal

6) General instruction

CAUTION

•Apply only the voltage specified in the instruction manual to

each terminal. Otherwise, burst, damage, etc. may occur.

•Ensure that the cables are connected to the correct terminals.

Otherwise, burst, damage, etc. may occur.

•Always make sure that polarity is correct to prevent damage, etc.

Otherwise, burst, damage may occur.

•While power is ON or for some time after power-OFF, do not

touch the inverter as it is hot and you may get burnt.

CAUTION

•Do not install or operate the plug-in option if it is damaged or

has parts missing.

•Do not stand or rest heavy objects on the product.

•Check that the mounting orientation is correct.

•Prevent other conductive bodies such as screws and metal

fragments or other flammable substance such as oil from

entering the inverter.

CAUTION

•Before starting operation, confirm and adjust the parameters.

A failure to do so may cause some machines to make

unexpected motions.

WARNING

•Do not modify the equipment.

•Do not perform parts removal which is not instructed in this

manual. Doing so may lead to fault or damage of the inverter.

CAUTION

•When parameter clear or all parameter clear is performed,

reset the required parameters before starting operations.

Each parameter returns to the initial value.

•For prevention of damage due to static electricity, touch

nearby metal before touching this product to eliminate static

electricity from your body.

CAUTION

•Do not test the equipment with a megger (measure insulation

resistance).

CAUTION

•Treat as industrial waste.

All illustrations given in this manual may have been drawn with

covers or safety guards removed to provide in-depth

description. Before starting operation of the product, always

return the covers and guards into original positions as specified

and operate the equipment in accordance with the manual.

— CONTENTS —

1 PRE-OPERATION INSTRUCTIONS 1

1.1 Unpacking and Product Confirmation .............................................................................................1

1.1.1 Product confirmation (FR-A700/F700 series) .................................................................................................1

1.1.2 Product confirmation (FR-E700 series (E kit))................................................................................................2

1.2 Parts....................................................................................................................................................3

1.3 Specifications.....................................................................................................................................4

2 INSTALLATION AND WIRING (FR-A700/F700 SERIES) 5

2.1 Pre-installation instructions .............................................................................................................5

2.2 Installation procedure .......................................................................................................................6

2.3 Wiring..................................................................................................................................................8

2.3.1 Wiring of FR-A7AX .........................................................................................................................................8

2.3.2 Wiring at inverter side...................................................................................................................................10

3 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) 12

3.1 Pre-Installation Instructions ...........................................................................................................12

3.2 Installation Procedure .....................................................................................................................12

3.3 Wiring................................................................................................................................................17

3.3.1 Wiring of FR-A7AX .......................................................................................................................................17

3.3.2 Wiring of inverter ..........................................................................................................................................19

4 CONNECTION DIAGRAM AND TERMINAL 20

4.1 Connection Diagram........................................................................................................................20

4.2 Internal Block Diagram....................................................................................................................22

4.3 Terminals ..........................................................................................................................................23

4.4 Code Input Example ........................................................................................................................24

5 PARAMETERS 25

5.1 Parameter List ..................................................................................................................................25

5.2 Parameter Setting ............................................................................................................................27

5.2.1 Selection of input method (Pr. 304) (FR-A700/F700 SERIES).....................................................................27

5.2.2 Selection of input method (Pr. 304) (FR-E700 series)..................................................................................28

5.2.3 Read timing operation selection (Pr. 305) ....................................................................................................29

5.2.4 Bias and gain adjustment (Pr. 300, Pr. 301, Pr. 302, Pr. 303) .....................................................................31

5.2.5 Digital input unit selection (Pr. 329)..............................................................................................................34

5.2.6 16-bit digital torque command (FR-A700 series only) ..................................................................................35

5.3 Instructions ......................................................................................................................................39

1PRE-OPERATION INSTRUCTIONS

1.1 Unpacking and Product Confirmation

Take the plug-in option out of the package, check the product name, and confirm that the product is as you

ordered and intact.

FR-A7AX is a plug-in option for the FR-A700/F700/E700 series.

1.1.1 Product confirmation (FR-A700/F700 series)

Check the enclosed items.

Plug-in option

......................................... 1

Mounting screw (M3 ×6mm)

.............. 2 (Refer to page 6.)

Hex-head screw for option

mounting (5.5mm)

............... 1 (Refer to page 6.)

5.5mm

PRE-OPERATION INSTRUCTIONS

1.1.2 Product confirmation (FR-E700 series (E kit))

Check the enclosed items.

*1 Used with the FR-E720-3.7K (FR-E720-175) or less and FR-E740-7.5K (FR-E740-170) or less.

*2 Used with the FR-E720-5.5K (FR-E720-240) or more and FR-E740-11K (FR-E740-230) or more.

Plug-in option

..............................................1

Mounting screw (M3

6mm)

................ 2 (Refer to page 14, 16)

Front cover for plug-in option

.................1 (Refer to page 14, 15)

Option protective cover *1

..................... 1 (Refer to page 14)

Option small cover *2

......................1 (Refer to page 15)

CAUTION

• Install a provided front cover for plug-in option, in place of the inverter front cover.

PRE-OPERATION INSTRUCTIONS

1.2 Parts

zFR-A7AX

X10

X11

X12

X13

X14

X15

Front view

Terminal layout

Rear view

Mounting

hole

Mounting hole

Mounting

hole

Terminal

block

Connector

Connect to the inverter

option connector

(Refer to page 6, 13, 15.)

PRE-OPERATION INSTRUCTIONS

1.3 Specifications

(1) Digital input signal type

BCD code 3-digit or 4-digit

Binary 12-bit or binary 16-bit

(2) Selection of digital input signal

Select from the operation panel or parameter unit.

(3) Input current

5mA(24VDC) for each circuit

(4) Input specifications

Relay contact signal or open collector input

(5) Adjustment function

⋅Bias and gain

⋅Analog compensation input (They can be set for the FR-A700/F700 series only.)

(Set using the operation panel)

2INSTALLATION AND WIRING (FR-A700/F700 SERIES)

2.1 Pre-installation instructions

Make sure that the input power of the inverter is OFF.

CAUTION

With input power ON, do not install or remove the plug-in option. Otherwise, the inverter and

plug-in option may be damaged.

For prevention of damage due to static electricity, touch nearby metal before touching this

product to eliminate static electricity from your body.

Andere Handbücher für 700 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FX-1PG Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A8NCE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-D700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PV-PNS03ATL-GER Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NC E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7AD Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Climaveneta i-BX-004-013M Einrichtungshandbuch

Mitsubishi Electric

Mitsubishi Electric FR-E800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PV-S4200-IT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A8APS-02 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-ABR-(H)0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Plus Series Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric FR-A820-00046 (0.4K) Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-HEL-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NCA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A8ND Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-LU08 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V5NS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-S500E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Merkblatt

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung