molex 207129 Series Bedienungsanleitung
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 1 of 9
Revision: C Revision Date: 10-06-10
Application Tooling
Specification Sheet
Tool Kit
Order No. 6 811-6470
Hand Crimp Tool
Order No. 6 811-6400
FEATURES
% A full cycle ratcheting hand tool ensures complete crimps
% Ergonomically designed soft handles
% Precisely designed crimping profiles with simple contact positioning
% Easy handling due to outstanding force ratio
Tool kits are easily installed into the Hand Crimp Tool or the 63816-0300 Power Crimp Head which is installed
into the 63816-0200 (110 V) or the 63816-0250 (220 V) Battery Powered Tool.
Many different Tool kits can be used with a single Battery Powered Tool.
This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant.
SCOPE
Products: 1.50mm (.059") Pico-SPOX™ Crimp Terminal, Female, 2 -30 AWG.
Terminal
Series No.
Terminal Order No. Wire Size Wire Type
Insulation Diameter
Maximum Strip Length
Available in Reel form only AWG mm² AWG Type mm In. mm In.
87 21 87 21-0000
2 0.20 2 UL1061 1.15 .0 5 1.05-1.5 .0 1-.061
26-30 0.12-0.05
26 UL1061
1.00 .039 1.05-1.5 .0 1-.061 28 UL1061
30 UL1571
Customer to cut off terminal from reel: 0.29mm (.011”) maximum Cut-off Tab.
See Conditions on page 2.
DEFINITION OF TERMS
TYPE 2C
INSULATION
CRIMP
▲
SEE NOTE
BRUSH
STRIP
LENGTH
BELL MOUTH
BEND
DOWN
BEND UP
ROLLING
CONDUCTOR
CRIMP
TWISTING
CRIMP HEIGHT
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 2 of 9
Revision: C Revision Date: 10-06-10
▲Insulation Crimp Note:
Due to the terminal’s insulation grip design
and/or insulation diameter range, this tool
uses “overlap” form geometry in the
insulation punch. This produces an overlap
insulation crimp (A620 – compliant). While
the insulation punch profile may appear
“lopsided”, this is a normal condition for this
tool. See figure to the right. (Some tools with
multiple crimp pockets may not have the
“overlap” profile on all pockets).
After crimping, the conductor profiles should
measure the following (see notes below).
Terminal Series No
Wire Size Conductor Crimp ●Insulation Crimp Pull Force
Minimum
Profile
Height (Ref.) Width (Ref.)
Height (Ref.)
Width (Ref.)
AWG
mm2
mm In. mm In. mm In. mm In. N Lb. A B
87 21
2 0.20 0.56-0.60
.022-.02
1.00 .039 1. 0 .055 1.10 .0 3 29.
6.60
X
26 0.12 0.52-0.58
.020-.023
1.00 .039 1.2 .0 9 1.10 .0 3 19.6
. 0
X
28 0.08 0.52-0.58
.020-.023
1.00 .039 1.2 .0 9 1.10 .0 3 9.8 2.20
X
30 0.05 0.52-0.58
.020-.023
1.00 .039 1.2 .0 9 1.10 .0 3 6.7 1.50
X
To Achieve IPC-A-620 Class 2 Crimps, the following over-all wire insulation diameter ranges are recommended:
Profile A: 1.00-1.15mm (.039-.0 5 inch)
Profile B: 0.65-1.00mm (.025-.039 inch)
Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
Note:
A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,
destructive, pull force test should be preformed to check hand tool crimp. Pull Force value Must exceed the
Minimum pull force specifications listed this page.
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage
can occur to the tool or die.
INSTALLATION
To install the Tool Kit into the Power Crimp Head follow the steps below:
Anvils and Punches Installation
1. Insert the Anvils into the bottom slots of the nest. Install the M x 10 long BHCS and tighten in place.
2. Insert the Punches into the top slots of the nest. Install the M x 18 long BHCS and tighten in place. See
Figure 1.
OVERLAP
INSULATION
CRIMP
OVERLAP FORM GEOMETRY
ANVIL
PUNCH
WIRE
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 3 of 9
Revision: C Revision Date: 10-06-10
SWING
LOCATOR
OPEN
PRESS DOWN
ON THE BRASS
PIVOT SHAFT
LIFT UP ON
THE LOCATOR
Figure 2
ANVILS
POWER
CRIMP
HEAD
Figure 1
PUNCHES
M4 X 10 LONG
BHCS
M4 X 18 LONG
BHCS
TERMINAL
SWING OPEN
PRESS HERE ON LOCATOR
LOCATOR TERMINAL IN PLACE
Figure 4
FRAME
Locator Installation and Removal
Follow the steps below to install or replace the locator. See Figure 2.
To install the locator
1. Position the locator with the hole over the brass pivot shaft and
snap it into place.
To remove the locator
1. Open the crimp hand tool.
2. Swing the existing locator open and away from the hand tool.
3. Firmly press down on the brass pivot shaft with your thumb,
while pulling the locator up. Slip the locator off the top of the
brass pivot shaft.
OPERATION
Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will
release the handles, and the hand tool will spring open.
Figure
LOCATOR
JAWS OPEN
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page of 9
Revision: C Revision Date: 10-06-10
Crimping Terminals
1. Select the desired terminal listed in the preceding charts.
2. Swing the terminal locator away from the crimp tool shown in
Figure . Gently press on the locator to open the wire stop.
Some terminals with large insulation grips may interfere with the
crimp tooling when swinging the locator into position. The
terminal must then be loaded into the locator in the closed/crimp
position.
3. When using the locator, swing the locator away from the crimp
tool, and gently press the locator against the tool frame as
shown in Figure . The wire stop will automatically open. Insert
the proper terminal into the proper nest opening. Make sure
when choosing the nest opening, it will correspond with the A or
B profile on the hand tool.
. Return the locator to its original position.
5. Insert the proper wire over the terminal. Some large O.D. wires
may need to be placed into the terminal before closing the tool.
Gently touch the wire stop with the end of the wire. See Figure
5.
6. Compress the terminal by squeezing the tool handles until the
ratchet mechanism cycle has been completed. Release
handles to open the jaws.
7. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on
the wire. The terminal locator can be in either position.
8. Visually inspect the crimped terminal for proper crimp location.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
Locator Replacement
See the parts list on the last page of this document for the
proper locator order number. Follow the steps below to replace
the locator.
1. Open the crimp hand tool.
2. Swing the existing locator open and away from the hand
tool.
3. Firmly press down on the brass pivot shaft with your
thumb, while pulling the locator up. Slip the locator off the
top of the brass pivot shaft. See Figure 6.
. Replace it with the proper locator by putting over the brass
pivot shaft and snapping it into place.
For the Battery Power Tool:
1. Cycle the Battery Power Tool to crimp the terminal to the wire.
2. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on
the wire. The terminal locator can be in either position.
3. Visually inspect the crimped terminal for proper crimp location.
SWING
LOCATOR
OPEN
PRESS DOWN
ON BRASS PIVOT
SHAFT
LIFT UP
LOCATOR
JAWS
OPEN
Figure 6
WIRE
LOCATOR
IN PLACE WIRE STOP
TERMINAL
WIRE STOP
WIRE
AGAINST STOP Figure 5
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 5 of 9
Revision: C Revision Date: 10-06-10
Maintenance
It is recommended that each operator of the
tool be made aware of, and responsible for,
the following maintenance steps:
1. Remove dust, moisture, and other
contaminants with a clean brush, or soft,
lint free cloth.
2. Do not use any abrasive materials that
could damage the tool.
3. Make certain all pins; pivot points and
bearing surfaces are protected with a thin
coat of high quality machine oil. Do not oil
excessively. The tool was engineered for
durability but like any fine piece of
equipment it needs cleaning and
lubrication for a maximum service life of trouble free crimping. Use a 30 weight automotive (light) oil used at
the oil points, every 5,000 crimps or 3 months, shown in Figure 7A or 7B will significantly enhance the tool life.
. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto
certain terminations may affect the electrical characteristics of an application.
5. When tool is not in use, keep the handles
closed to prevent objects from becoming
lodged in the crimping dies, and store the tool
in a clean, dry area.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a
partially closed position, Do Not force the handles
open or closed. The tool will open easily by
pressing the ratchet release lever. See Figure 8.
How to Adjust Tool Preload
(See Figure 8)
This hand tool is factory preset to 25- 5 LBS.
preload. It may be necessary over the life of the tool to adjust tool handle preload force. Listed below are the
steps required to adjust the crimping force of the hand tool to obtain proper crimp conditions:
1. Remove or fold back the handle grip from the handle to expose the eccentric axle and setting wheel.
2. Remove the locking screw with a 2mm hex wrench. The wrench set (63810-0101), is not supplied. It is sold
separately from the hand tool.
3. Turn the eccentric axle and setting wheel with the wrench or pliers Counter-clockwise (CCW) to increase
handle force.
. Replace the locking screw, aligning the nearest notch in the setting wheel to locking screw.
5. Replace the handle grip.
6. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted.
RATCHET
RELEASE LEVER
Figure 8
HANDLE
GRIP
REMOVED
ECCENTRIC AXLE
HANDLE
GRIP
LOCKING
SCREW
WRENCH SET
(SOLD
SEPERATELY)
PRELOAD
CHECK POINT
25.4MM
SETTING WHEEL
Figure 7B
LUBRICATION
POINTS
(BOTH SIDES)
LIGHT OIL
(EVERY MONTH
OR
5,000 CRIMPS)
Figure 7A
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 6 of 9
Revision: C Revision Date: 10-06-10
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will
not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,
fixturing, or use of handle extensions voids this warranty.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
CAUTIONS
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
. Use only the Molex terminals specified for crimping with this tool.
Certification
Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for
customers to re-certify hand tools.
% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped
12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than
25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull
testing.
% If the tool does not meet minimum pull force values, handle preload should be increased and the pull test
rerun, (See How To Adjust Preload).
% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and
replaced.
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 7 of 9
Revision: C Revision Date: 10-06-10
The chart below shows all applications for this Tool Kit.
Tool Kit
Order No.
Tool
Order no.
Tool
Description
Power Head
Order No.
Adapter
Description
Figure
No.
63811-6 70
63810-0100
Hand Crimp Frame (Short) N/A N/A 9
63810-0 00
Hand Crimp Frame (Long) N/A N/A 9
63816-0200
Battery Power Tool (110 V)
63816-0300 Power Crimp Head
10
63816-0250
Battery Power Tool (220 V)
63816-0300 Power Crimp Head
10
Applications for the Tool Kit
Hand Crimp Tool Battery Powered Tool
Figure 9 Figure 10
WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper
instruction and without first reading and understanding the instructions in the proper Manual or
Specification Sheet. See Chart above for the correct Manual or Specification Sheet.
WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the
power is turned off.
CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.
CAUTION: Wear safety glasses when operating or serving this tool.
POWER
CRIMP
HEAD
LOCKING PINS
BATTERY
POWERED
TOOL
TOOLING KIT
HAND CRIMP
FRAME LONG
AND SHORT
TOOLING
KIT
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 8 of 9
Revision: C Revision Date: 10-06-10
RATCHET
RELEASE SCREW
Figure 11
1
M4 X 6mm
LONG BHCS
M4 X 12mm
LONG BHCS
5
6
WITH TOOL KIT
LOCATOR ONLY
M4 X 12mm
LONG BHCS
4
4
2
5
HAND TOOL PARTS LIST
Item Number Order Number Description Quantity
1 63810-0100 Hand Crimp Frame (Short) 1
2 63810-0101 Wrench Set (Not included) 0
3 63810-0102 Locator Base 1
63810-0103 Repair Kit (Not included) 0
5 63811-6 70 Tool Kit with Locator 1
6 63811-6 75 Locator (only) REF
Tool Kit for Pico-SPOX™ Crimp Terminals
Doc No: ATS-638116 HM Release Date: 06-19-06 UNCONTROLLED COPY Page 9 of 9
Revision: C Revision Date: 10-06-10
Figure 12
1
2
2
M4 by 8 Long
BHCS
M4 by 18 Long
BHCS
M4 by 10 Long
BHCS
1
POWER HEAD PARTS LIST
Item Order No Engineering No. Description Quantity
1
63816-0300 63816-0300 Power Crimp Head 1
2
63811-6 70 63811-6 70 Tool Kit 1
http://www.molex.com
Andere Handbücher für 207129 Series
100
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere molex Crimpwerkzeuge Handbücher
molex
molex AT-200 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63813-2100 Bedienungsanleitung
molex
molex 63811-5800 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex CR60927A Bedienungsanleitung
molex
molex 63819-4900 Bedienungsanleitung
molex
molex 63811-6170 Bedienungsanleitung
molex
molex 63825-0500 Bedienungsanleitung
molex
molex 64005-6200 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex CR60622B Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 35745 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 200218-2600 Benutzerhandbuch
molex
molex 63825-6670 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63825-3000 Bedienungsanleitung
Beliebte Crimpwerkzeuge Handbücher anderer Marken
Panduit
Panduit CT-1000 Administratorhandbuch
JST
JST CS 10 Bedienungsanleitung
Danfoss
Danfoss ET4200 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
TE Connectivity
TE Connectivity 2063528-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics 69156-1 Bedienungsanleitung
Textron
Textron ESG105L Bedienungsanleitung
Tyco Electronics
Tyco Electronics 90035-3 Bedienungsanleitung
Emerson
Emerson Klauke ES 20RMCCFB Bedienungsanleitung
Continental Refrigerator
Continental Refrigerator PC150HD Bedienungsanleitung
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung