Monte Carlo Fan Company Ceiling fan Bedienungsanleitung

Page 1 – Designer upreme-English CUL

OWNER’

MANUAL

READ AND AVE THE E IN TRUCTION

For Designer Supreme Fans

Ceiling Fan Installation Instructions

92 QUALITY CEILING FAN

Total fan weight

Page 2 – Designer upreme-English CUL

123

TOOLS REQUIRED

Phillips Screw river Wire Cutters Pliers Step La er

Unpack and inspect fan carefully to be

certain all contents are included. ( ee

exploded view parts list.)

Turn off power at breaker box to avoid

possible electrical shock.

Use outlet box suitable for fan support.

ecure outlet box directly to the building

structure using ceiling joist screws. Outlet

box must support 35 lbs.

4Install mounting bracket to outlet box in

ceiling using the screws provided with

the outlet box and washers. 5

Feed motor lead wires through downrod/

canopy assembly and insert downrod into

motor yoke. Next, insert clevis pin through

yoke and downrod and secure with cotter

pin. (see inset) Tighten both yoke set

screws to further secure downrod. 6

Carefully lift fan assembly onto mounting

bracket. Rotate fan so that the notch on

the ball engages the ridge in the

mounting bracket. This will allow hands-

free wiring.

Clevis

Pin et

crews

Cotter

Ridge Ball

Notch

Safety Tips

WARNING: TO REDUCE THE RI K OF FIRE, ELECTRIC HOCK, OR INJURY TO PER ON , OB ERVE THE FOLLOWING:

READ AND AVE THE E IN TRUCTION

IN TALLATION

10.

11.

12.

13.

14.

15.

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards(AN I/NFPA 70-

1993), including fire-rated construction.

Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, witch power off at ervice panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the

floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and use

mounting screws and washers provided with the outlet box. (Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NEPA), and the

American ociety for Heating, Refrigeration and Air Conditioning Engineers (A HRAE) and the local code authorities.

Before servicing or cleaning unit, witch power off at ervice panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

Page 3 – Designer upreme-English CUL

2While the fan assembly is still on the

ground thread the safety cable through

the mounting bracket.

safety cable

mounting

bracket

Lift fan assembly and install the safety cable

directly to the building structure using the 3" lag

screw and plain washer provided. Before

proceeding to the next step make sure that the

cable is properly installed and will support

the fan weight. Make sure the screw

washer and safety cable are installed using

the order pictured above.

Ball

Notch

Install mounting bracket to outlet box in

ceiling using the screws provided with the

outlet box and washers.

Feed motor lead wires through downrod/

canopy assembly and insert downrod into

motor yoke. Next, insert clevis pin through

yoke and downrod and secure with cotter

pin. (see inset) Tighten both yoke set

screws to further secure downrod.

Clevis

Pin et

crews

Cotter

Ridge

plain

washer

safety cable

3" lag

screw

WARNING: MOUNT ONLY TO AN OUTLET BOX MARKED

ACCEPTABLE FOR FAN SUPPORT

All set screws must be checked and retightened where

necessary before installation.

Ca adia Safety Tips

A. Carefully lift fan assembly onto mounting

bracket. Rotate fan so that the notch on

the ball engages the ridge in the

mounting bracket. This will allow hands-

free wiring. For wiring instructions please

refer to page 4 step #7.

Ca adia Mou ti g System I sert

Page 4 – Designer upreme-English CUL

Note:

After installation, please refer to operation, maintenance and troubleshooting sections in this manual.

If your fan is packaged with a light kit or if you wish to install a separately purchased light kit,

please refer to the insert sheet titled: L

IGHT

NSTALLATION

IN TALLATION

WIRING OPTION WITH WALL PEED CONTROL

Wall

control

Light witch

Fan witch

For control of fan and optional light from

wall location, follow diagram above.

NOTE: A professional electrician is

recommended for this type of installation.

*ATTACH BLUE WIRE

ONLY IF ATTACHING

LIGHT KIT WITH FAN

ecure with

twist-lock

wire

connectors

(included)

For pullchain controls, follow diagram above. Make

sure that all exposed wiring is secured inside wire

nuts. Note: Wires from house may vary in color and

may not include ground wire. After wiring is

conplete, gently push wires into junction box

with wire nuts pointing upward. Refer to point

3 of safety tips.

TANDARD WIRING OPTION

Raise the canopy up and align the two

holes in the canopy with the two holes in

the hanger bracket. ecure with two 5/

32 x 1/2" screws provided.

COMBO-BLADE

Combo-Blades feature two high quality

finishes on one blade. elect the one that

best complements your decor, or change

the style with just a flip of the blade.

Fiber

Washers

Attach blade brackets to blades using

the blade bracket screws and washers

provided.

12 13

Remove plastic shipping stabilizer tabs,if

present.The screws,washers and motor pads are

pre-installed to the blade holders.Attach blade

assembly to motor by tightening first screw

one turn,then tighten second screw

securely.Then,go back and tighten first

screw securely.

hipping

tabilizer

Tab

14 After attaching blade; reinstall the

switch housing using the three screws

previously removed.

To gain access to the blade bracket

attachment holes remove the switch

housing cover by unscrewing the three

screws. Gently slide the cover off .

Page 5 – Designer upreme-English CUL

TROUBLE HOOTING GUIDE

CU TOMER ERVICE CENTER:

2900 WE T EMINARY DR.

FORT WORTH, TEXA 76133

1-800-519-4092

SUGGESTED REMEDY

TROUBLE

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3. Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is in the middle.

4. Make sure that shipping stabilizer tabs have been removed from motor (see installation step #13).

1. Check to make sure all screws in motor housing are snug (not over tightened).

2. Check to make sure the screws which attach the fan blade holder to the motor are tight.

3. Check to make sure wire nut connectors in switch housing are not rattling against each other or against the interior wall of

the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4. If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are finger tight. Check to be

sure light bulb is tight in socket and not touching glass shade(s). If vibration persists from glass, remove glass and install a

1/4" wide rubber band on glass neck to act as an insulator. Replace glass and tighten screws against rubber band.

5. ome fan motors are sensitive to signals from olid tate variable speed controls. DO NOT U E a olid tate variable speed

control.

6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this period.

1. Make sure that the ridge of the canopy engages the notch in the downrod ball. ( ee illustration in tep #6 of Downrod

Mount installation).

2. Check that all blades are screwed firmly into blade holders.

3. Check that all blade holders are tightened securely to motor.

4. Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box is mounted

firmly to ceiling joist.

5. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling

above the tip of one of the blades. Measure this distance as shown in Figure 1. Keeping measure within 1/8", rotate the fan

until the next blade is positioned for measurement. Repeat for each blade. If all blade levels are not equal, you can adjust

blade levels by the following procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and

blade holder at the screw closest to the motor (Figure 2). To adjust a blade tip up, insert washer (not supplied) between the

blade and blade holder at the two screws farthest from the motor (Figure 2).

6. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly

result in smoother operation.

1. Check blue wire from fan to make sure it is connected to hot wire from house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

4. Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

1. If fa does ot start:

2. If fa sou ds oisy:

3. If fa wobbles:

Touching

Ceiling

Figure 1

Blade Tip Dow :

Blade Tip Up:

Fan Blade

Figure 2

Blade Brackets

4. If light does ot work:

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or

wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please

check this Trouble hooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installa-

tion, please call our Customer ervice Center at the number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, witch power off at ervice panel and lock service disconnecting means

to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag, to the service panel.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR52XX Fan Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Rockland 4RKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-560M Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LOR52BSD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54XX Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 5AGR56XXD series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5UPR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4BFR54 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SU54BK Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BY52XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STMSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WFXX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Centro Max 5CQM52-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ALR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OBSHR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3LRR66 Service-Handbuch

Monte Carlo Fan Company

Monte Carlo Fan Company Melody 3MER56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LDO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CY60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company BF1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GMR52XXD Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung