Morphy Richards Bagless Vacuum Cleaner Bedienungsanleitung

www.morphyrichards.com

Cyclonic bagless vacuum cleaner

Please read and keep these

instructions

getting the best from

your new cleaner...

If your cleaner isn’t picking up as well as it should,

please check

• Dust canister

It is important to regularly empty the canister even if it does not

appear full.

• Filters

It is important that the pleated filter is shaken clean each time

the dust canister is emptied to allow air through the appliance.

Wash the canister filters regularly in warm water and allow to

air dry. A spare pleated filter is included.

• Blockages

Check the hose, tubes and tools for blockages

• Belt

Check and replace damaged or broken belt

• Height adjustment

The height adjustment only comes into effect when the handle is

released by the handle release pedal È.

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 1

Important safety

instructions

The use of any electrical appliance requires

the following of common sense safety rules.

Primarily there is danger of personal injury

and secondly danger of damage to the

appliance and property. These are indicated in

the instructions text by the following two

conventions:

WARNING: Danger of personal injury

IMPORTANT: Damage to the appliance

In addition we offer the following essential

safety advice.

Location

• Do not use or keep this product outside

when it is raining.

• Do not store the appliance near hot ovens or

heating appliances.

Mains lead

• Do not allow the mains lead to become

strained or run this appliance over it.

• If the electrical cable becomes damaged the

complete cable assembly must be replaced.

Do not attempt this task yourself, contact

Morphy Richards using the helpline number.

Children

• Children do not understand the dangers

associated with operating electrical

appliances. Never allow children to use this

appliance.

Other safety considerations

• Never use in the presence of explosive

liquids or vapours.

• Never pick up inflammable or poisonous

liquids such as petrol, copier toner, or other

volatile substances. Never pick up acids,

asbestos or asbestos dust.

• Never use the appliance without the filters

installed.

• Never use the appliance to vacuum hot

ashes, broken glass, sharp objects or

liquids.

• Never modify the cleaner in any way.

• Always disconnect the appliance from the

mains supply after use or prior to cleaning or

emptying.

• The appliance should never be left running

unsupervised.

• Repairs to electrical appliances are only to

be undertaken by trained personnel.

Unprofessional repairs can be dangerous for

users.

• Use only genuine Morphy Richards spare

parts and accessories

• Never over-extend the hose such that the

cleaner is pulled over. If the cleaner is

knocked over, switch off before attempting

to upright.

• Never pick the cleaner up by the floor nozzle

when connected to the mains, use the

carrying handle.

• WARNING: Keep loose clothing, hair,

fingers etc. away from the floor nozzle

whenever the cleaner is connected to

the mains.

• Disconnect from the mains supply before

attempting to clear blockages, clear the

brush or replace the belt.

Electrical

requirements

Check that the voltage on the rating plate of

your appliance corresponds with your house

electricity supply which must be A.C.

(Alternating Current).

If the socket outlets in your home are not

suitable for the plug supplied with this

appliance, the plug should be removed and the

appropriate one fitted.

WARNING: The plug removed from the

mains lead, if severed, must be destroyed

as a plug with bared flexible cord is

hazardous if engaged into a live socket

outlet.

Should the fuse in the 13 amp plug require

replacement, a BS1362 13 amp fuse must be

fitted.

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 2

Features

⁄Vari power slider (certain models only)

¤Front cover release

‹Removable front cover

›Exhaust filter grille

ﬁCarpet height adjustment knob

ﬂFloor nozzle with powered brush

‡Upper handle

·Flexible hose

‚Cord storage with quick release cleat

„On/Off switch

‰Carrying handle

ÂNested extension tubes (2)

ÊCrevice nozzle

ÁFurniture brush

ËHose clip slot

ÈHandle release pedal

ÍHose connector

ÎDust canister release (shown page 5)

ÏDust canister lid

ÌPleated circular filter

ÓDust canister

ÔCentral mesh filter

Canister handle

ÒMotor protection filter (shown page 6)

ÚExhaust filter (page 6)

ÛBelt cover (shown page 7)

ÙBrush bar (page 7)

ıMotor shaft (shown page 7)

ˆBrush bar end caps (shown page 7)

˜Hose clip

¯Turbo nozzle (certain models only)

˘ Belt guard (shown page 7) 3

Accessories included Extension tubes

Crevice tool

Furniture brush

‡

ﬁ

›

ﬂ

‹

‚

‰

„

⁄

Ó

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 3

Assembly

WARNING: Do not plug in the cleaner

until it is assembled.

1Carefully unpack all components.

2Lift cleaner body to upright position.

3Remove the two screws that are already

attached to the body.

4From the rear of the cleaner, align the handle

with groove and slide into the body. If

necessary, use thumb and finger pressure to

slide handle into position.

5Fasten the handle with the two screws.

Floor nozzle height

adjustment

Before using the cleaner the floor nozzle

height must be set to the correct height.

Choose the setting which most closely

matches your floor surface.

• Use the TOOLS setting when using the

tools.

Note: The height adjustment only comes

into effect when the handle is released by the

handle release pedal È.

Variable power

(Certain models only)

Slide the variable power control to the right

to increase the suction power or to the left to

decrease suction. This feature is most useful

when using the hose and accessories. Use the

minimum setting when vacuuming delicate

fabrics/curtains etc. When not using the hose it

is advisable to keep the variable slider set to

maximum.

Using on carpets

1Place cleaner in its upright position.

2Set the carpet height adjustment knob to the

desired position.

3Release the mains cable by revolving the

quick release cleat 1/2a turn and extend the

cable fully.

4Plug the cable into the mains socket.

5Step on the handle release pedal to release

the handle to the desired position.

6Press the on/off button to the ‘on’ position.

IMPORTANT: To prevent damage to carpets,

never leave the cleaner switched on in one

place for an extended period.

• Never have the brushes set too low such

that the cleaner is hard to push.

Using attachments

Follow steps 1-4 but set the carpet height

adjustment knob to the TOOLS setting.

5Remove the hose connector Ífrom the

rear of the cleaner. Lift the hose ·from the

top handle hook. Insert the hose clip ˜into

the hose clip slot Ë.

• Push the required attachment firmly onto the

end of the hose.

• If additional length is required, attach one or

both extension tubes.

6Switch on/off.

• IMPORTANT: Always fix the hose clip ˜to

the main body slot Ëwhen using the hose

min max

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 4

and tools.

• Never over extend the hose such that the

cleaner is pulled over.

IMPORTANT: Turning the cleaner sideways

helps prevent the cleaner being pulled along by

the stretch hose.

Using & cleaning turbo nozzle

(Certain models only)

Attach the turbo nozzle to the hose end

connector Ífor use on upholstery and stairs.

After use your turbo nozzle may become

clogged. Turn over the nozzle and pull away

any hairs or fibres. If they are tightly wound

around the brush carefully snip the fibres with

scissors, being careful not to damage the brush

bar, pull away from the brush bar and dispose.

Emptying

Empty the dust canister regularly even if it

does not look full this will maintain the

performance.

1Remove the front cover by lifting the cover

release lever ¤E.

2Lift-up the dust canister release Îand pull

the canister away from the main body.

3Take the canister to the dustbin.

4Turn the lid 1/4turn anti-clockwise to unlock,

lift off the lid with pleated filter, Ìput to one

side. F

5Lift out the central mesh filter Ôfrom the

dust canister ÓG. Brush clean if

necessary.

6Empty out the dust canister Ó.

7Re-fit the central mesh filter.

8Shake the pleated filter to remove all dust.

9Re-fit pleated filter with lid into the dust

canister by lining up the two arrows and

turning the lid 1/4turn clockwise to lock.



‹

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 5

10 Re-fit dust canister into cleaner and push to

lock into position. Then re-fit front cover.

Safety cut-out

If the cleaner overheats a motor protection

thermostat will automatically switch the motor

off. If this happens, switch the cleaner off,

unplug from the power supply and leave

the cleaner to cool for at least 30

minutes. Check the airways for blockages,

empty dust canister and clean the filters before

restarting.

Cleaning the filters

To maintain suction the pleated filter

must be shaken clean each time the dust

canister is emptied. Failure to clean the filter

will reduce suction and could damage the

motor if used for a prolonged period. This may

invalidate the guarantee. If the filters become

damaged they must be replaced.

Pleated filter

This must be shaken clean at every

emptying to maintain suction. To thoroughly

clean it wash it regularly.

To remove it from the dust canister lid turn

the filter 1/4turn anti-clockwise. HWash in

warm water (no detergent) and allow to air dry

before refitting. The spare pleated filter allows

one filter to be washed and dried whilst the

other is in use.

Motor protection filter

The motor protection filter Òis located

underneath the dust canister

1Remove the dust canister.

2Lift out the filter and shake over a dustbin.

The filter may also be washed in water (no

detergents) but must be totally dry before re-

fitting.

3Replace the filter

Exhaust filter

The exhaust filter is located below the dust

canister compartment.

1Remove the front cover.

2Remove the exhaust filter Úby pulling

forward at the top and lift it away.

3Take the filter out of the cage and shake

vigorously over a dustbin. The filter may also

be washed in warm water. Do not use

detergents. The filter must be completely dry

before re-fitting. Allow filters to air dry

naturally.

4Replace the filter and front cover.

Changing the belt

If the brush bar stops rotating it is likely that

the drive belt has snapped (usually because the

brush has been stalled). A spare belt is

supplied. Replacement belts can also be

obtained from Morphy Richards.

Accessing the floor nozzle

1Disconnect the cleaner from the mains

supply.

2Put switch to off position.

3Remove front cover and dust canister.

4Press the handle release pedal and place

the cleaner face down, in a flat position on a

soft surface (eg carpet).

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 6

5Using a flat bladed screwdriver or a coin,

rotate the three cover fixings, a quarter of a

turn, from lock to unlock J.

6Lift the base cover, from the rear fixing area

first, the cover will rotate forward. Unhook

cover from front edge and remove N.

Removing rotating brush & belt

7Lift the metal belt guard ˘ out of the floor

nozzle and put it safely to one side K.

8Slide the belt past the end of the motor drive

shaft. If the belt has broken remove al pieces

and clean the drive shaft.

9Lift the rotating brush equally at both ends

to slide it free of the floor nozzle L. Holding

the ends of the brush check it rotates freely

if not, it must be replaced. Call our Helpline

for replacement parts or belts.

Re-fitting rotating brush & belt

10 Hook the belt over the the drive shaft (the

belt must be slid sideways past the end of

the drive shaft). Note: Belt guard must have

been removed first, see 7 above.

11 Refit the belt guard, ensuring it is correctly

located. Press down fully.

12 Pass the rotating brush through the belt

ensuring the correct end is located against

the belt M.

13 Pull the brush forward (against the pull of the

belt) and locate the square ends of the brush

into the location slots in the floor nozzle M.

14 Rotate the brush by hand to ensure the belt

is running in the center of its location on the

brush.

Refitting floor nozzle base cover

15Hook the base cover into the front of the

floor nozzle, ensuring all four hooks are

engaged N.

16Rotating the cover downwards and

rearwards, slowly close the cover.

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 7

17Tighten three fixings, using screwdriver to

turn fixings a quarter of a turn to the lock

position J.

Note: If the cover will not fully close or

fixings will not lock, lift the cover slightly

and rotate fixings until they are in the

correct position for closure.

18Return cleaner to the upright position,

re-fit dust canister and front cover.

Connect to the mains supply. Switch on

to test.

Your two-year

guarantee

• It is important to retain the retailers

receipt as proof of purchase. Staple your

receipt to this back cover for future

reference.

Please quote the following information if the

product develops a fault. These numbers can

be found on the base of the product.

Model no. Serial no.

All Morphy Richards Products are

individually tested before leaving the factory. In

the unlikely event of any appliance proving to

be faulty within 28 days of purchase it should

be returned to the place of purchase for it to be

replaced.

If the fault develops after 28 days and within

24 months of original purchase, you should

contact the helpline number quoting model

number and serial number on the product, or

write to Morphy Richards at the address

shown. You will be asked to return the product

(in secure, adequate packaging) along with a

copy of proof of purchase. Subject to the

exclusions set out below (1-6), the faulty

appliance will then be repaired or replaced and

dispatched usually within seven working days

of receipt.

If for any reason this item is replaced during

the 2-year guarantee period, the guarantee on

the new item will be calculated from original

purchase date. Therefore it is vital to retain your

original receipt or invoice to indicate the date of

initial purchase.

To qualify for the two-year guarantee the

appliance must have been used according to

the manufacturers instructions. For example the

filters shall have been regularly cleaned as

instructed.

Morphy Richards shall not be liable to

replace or repair the goods under the terms of

the Guarantee where:

EXCLUSIONS

1The fault has been caused or is attributable

to accidental use, mis-use, negligent use or

used contrary to the manufacturers

recommendations or where the fault has

been caused by power surges or damage

caused in transit.

2The appliance has been used on a voltage

supply other than that stamped on the

products.

3Repairs have been attempted by persons

other than our service staff (or authorised

dealer).

4Where the appliance has been used for hire

purposes or non-domestic use.

5Morphy Richards are not liable to carry out

any type of servicing work, under the

guarantee.

6Consumables such as the filters and belt are

not covered by the guarantee.

This guarantee does not confer any rights

other than those expressly set out above and

does not cover any claims for consequential

loss or damage. This guarantee is offered as an

additional benefit and does not affect your

statutory rights as a consumer.

• This guarantee is valid in the UK and Ireland

only.

VC73360MUK Rev 3 11/05

The After Sales Division,

Registered address,

Morphy Richards Ltd, Mexborough,

South Yorkshire, England, S64 8AJ

Helpline (office hours)

UK 0870 060 2604

Republic of Ireland 1800 409119

Morphy Richards products are intended for

household use only

Morphy Richards has a policy of continuous

improvement in product quality and design. The

Company, therefore, reserves the right to change

the specification of its models at any time.

VC73360MUK-CyclonicBaglessRev3 3/11/05 4:41 pm Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Morphy Richards Staubsauger Handbücher

Morphy Richards

Morphy Richards Ecovac 70096 Rev 2 (Page 1) Bedienungsanleitung

Morphy Richards

Morphy Richards Ecovac 70096 Bedienungsanleitung

Morphy Richards

Morphy Richards PERFORMAIR CYCLONIC VACUUM CLEANER Bedienungsanleitung

Morphy Richards

Morphy Richards Goblin 73276 Bedienungsanleitung

Morphy Richards

Morphy Richards STORM CYCLONIC vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Bedienungsanleitung

Morphy Richards

Morphy Richards Scoot cylinder vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards VC73410 MUK Bedienungsanleitung

Morphy Richards

Morphy Richards Bagless Cylinder Vacuum Cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards Steam cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards PERFORMAIR CYCLONIC VACUUM CLEANER 71062 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Bedienungsanleitung

Morphy Richards

Morphy Richards IB73091 Bedienungsanleitung

Morphy Richards

Morphy Richards IB71051 Bedienungsanleitung

Morphy Richards

Morphy Richards ESSENTIALS CYCLONIC BAGLESS UPRIGHT VACUUM CLEANER - REV... Bedienungsanleitung

Morphy Richards

Morphy Richards 73285 BAGLESS UPRIGHT VACUUM CLEANER Bedienungsanleitung

Morphy Richards

Morphy Richards IB70240 Bedienungsanleitung

Morphy Richards

Morphy Richards 73380 Bedienungsanleitung

Morphy Richards

Morphy Richards Storm Bedienungsanleitung

Morphy Richards

Morphy Richards 73281 Bedienungsanleitung

Morphy Richards

Morphy Richards ESSENTIALS COMPACT BAGLESS VACUUM CLEANER - REV... Bedienungsanleitung

Morphy Richards

Morphy Richards 73332 Bedienungsanleitung

Morphy Richards

Morphy Richards Scoot bagless vacuum cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards IB70191 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch