Moxa Technologies EDS-210A-1GTX-1GSFP-4SFP Bedienungsanleitung

P/N: 1802002100012

*1802002100012*

EDS-210A

Quick Installation Guide

Moxa EtherDevice Switch

Edition 3.0, February 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

EDS-210A series 10-port industrial Ethernet switches are equipped with 1

Gigabit fiber optic Ethernet port, up to 8 10/100M copper ports, and 4

100M fiber optic Ethernet ports, making it ideal for applications that

require high bandwidth data convergence and long-distance uplinks. The

EDS-210A series provides 12/24/48 VDC redundant power inputs, has a

rugged IP30-rated metal housing, and is DIN-rail mountable. These

switches are compliant with FCC/UL/CE standards and undergo a 100%

burn-in test to ensure that they fulfill the special needs of industrial

automation control applications. The EDS-210A series has a -10 to 60°C

operating temperature range and is also available with wide-temperature

operation (-40 to 75°C).

NOTE

Throughout this Hardware Installation Guide, we use EDS

as an

abbreviation for Moxa EtherDevice Switch:

EDS = Moxa EtherDevice Switch

Package Checklist

Your EDS is shipped with the following items. If any of these items is

missing or damaged, please contact your customer service

representative for assistance.

•Moxa EtherDevice™ Switch

•Protective caps for unused ports

•Quick installation guide (printed)

•Warranty card

Features

High Performance Network Switching Technology

•10/100/1000BaseT(X) (EDS-210A-1GTX-1GSFP-4SFP only),

10/100BaseT(X) auto-negotiation speed, full/half duplex mode, auto

MDI/MDI-X connection, and 100Base SFP slot /1000Base SFP slot.

•IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X), IEEE 802.3ab

for 1000BaseT, and IEEE 802.3z for 1000BaseX.

•Store-and-forward switching process type.

Rugged Design

•Operating temperature range of -10 to 60°C, or extended operating

temperature of -40 to 75°C (T models only)

•IP30, rugged high-strength case

•DIN-rail or panel mounting available

•Redundant dual 12/24/48 VDC

- 3 -

Panel Layout of EDS-210A-1GSFP-1SFP/

EDS-210A-1GTX-1GSF-4SFP

1. Grounding screw

2. Terminal block for power input

(PWR1, PWR2) and relay output

3. Power input PWR1 LED

4. Power input PWR2 LED

5. TP port’s 10/100 Mbps LED

TP port’s 10/100/1000 Mbps LED

7. SFP port's 100Mbps LED

8. SFP port's 1000Mbps LED

9. Port number

10.

10/100 BaseT(X) Port

11.

10/100/1000 BaseT(X) Port

12.

100Base SFP slot

13.

1000Base SFP slot

14.

Model Name

15.

Screw hole for wall mounting kit

16.

DIN rail kit

- 4 -

Mounting Dimensions unit = mm (in)

DIN-Rail Mounting

The aluminum DIN-rail attachment plate should already be fixed to the

back panel of the EDS when you take it out of the box. If you need to

reattach the DIN-rail attachment plate, make sure the metal spring is

situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN

-rail into

the slot just below the metal spring.

STEP 2:

The DIN

-rail attachment unit will

snap into place as shown below.

To remove the DIN-rail from the EDS, simply reverse Steps 1 and 2.

Wall Mounting (optional)

For some applications, you will find it convenient to mount the EDS on the

wall, as illustrated below.

STEP 1:

Remove the aluminum DIN

rail

attachment plate from the

EDS’s rear panel, and then

attach the wall mount plates, as

shown in the

figure.

- 5 -

STEP 2:

Mounting

the

EDS on the wall requires 4 screws. Use the

witch, with wall mount plates attached, as a guide to

mark the correct locations of the 4 screws. The heads of

the screws should be less than 6.0 mm in diameter, and

the shafts should be less than

3.5 mm in diameter, as

shown in the figure at the right.

NOTE

Before tightening screws into the wall, make sure the screw head

and shank size are suitable by inserting the screw into one of the

keyhole-shaped apertures of the wall mounting plates.

Do not tighten the screws all the way in — leave about 2 mm to allow

room for sliding the wall mount panel between the wall and the screws

STEP 3

Once the screws are fixed in

the wall, insert the four

screw heads through the

large parts of the

keyhole

-shaped apertures,

and then slide the EDS

downwards, as indicated.

Tighten the four screws for

added

stability.

Wiring Requirements

WARNING

Safety First!

Turn

the power off before disconnecting modules or wires. The

proper

power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT use a voltage greater than

what is

specified on the product label.

These devices must be supplied by a

AELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

- 6 -

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring for all devices in the system

when necessary.

Grounding the Moxa EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Wiring the Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power

sources. If one power source fails, the other live source acts as a backup,

and automatically supplies the EDS-210A with power.

The two 2-contact terminal block connectors on the EDS's top panel are

used for the EDS's two DC power inputs. Top and front view of the

terminal block connectors are shown here.

Step 1: Insert the negative/positive DC wires into the

-/V+ terminals

Step 2: To keep the DC wires from pulling loose, use a

small flat

-blade screwdriver to tighten the wire-clamp

screws on the front of the terminal block connector.

Step 3:

Insert the plastic terminal block connector

prongs into the terminal block receptor, which is located

the EDS’s top panel.

ATTENTION

Before connecting the EDS

-210A to the DC power inputs, make

sure the DC power source voltage is stable.

- 7 -

Communication Connections

EDS-210A models have 10/100BaseT(X) Ethernet ports,

10/100/1000BaseT(X) Ethernet ports,100BaseSFP and 1000BaseSFP.

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the EDS’s front panel are used to

connect to Ethernet-enabled devices.

Next, we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also show cable wiring diagrams for

straight-through and cross-over Ethernet cables.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

10/100/1000BaseT(X) Ethernet Port Connection

The 10/100/1000BaseT(X) ports located on Moxa EtherDevice Switch’s

front panel are used to connect to Ethernet-enabled devices. Most users

will choose to configure these ports for Auto MDI/MDI-X mode, in which

case the port’s pinouts are adjusted automatically depending on the type

of Ethernet cable used (straight-through or cross-over), and the type of

device (NIC-type or HUB/Switch-type) connected to the port.

In the following section, we give pinouts for both MDI (NIC-type) ports

and MDI-X (HUB/Switch-type) ports. We also give cable wiring diagrams

for straight-through and cross-over Ethernet cables.

- 8 -

10 /100Base T(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

1000BaseT RJ45 Pinouts

MDI

MDI-X

BI_DA+

BI_DB+

BI_DA-

BI_DB-

BI_DB+

BI_DA+

BI_DC+

BI_DD+

BI_DC-

BI_DD-

BI_DB-

BI_DA-

BI_DD+

BI_DC+

BI_DD-

BI_DC-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

- 9 -

100Base-FX or 1000Base-X Fiber Port

The Fiber ports on the EDS-210A series are SFP type slots, which support

both 100Base-FX and 1000Base-X speed fiber transceiver to work

properly. Moxa provides complete transceiver models for various distance

requirements.

Multi-mode:

1000BaseSX

0 to 550 m, 850 nm (50/125μm, 400MHz*km)

0 to 275 m, 850 nm (62.5/125μm, 200MHz*km)

1000BaseLX

0 to 1100 m, 1310 nm (50/125μm, 800MHz*km)

0 to 550 m, 1310 nm (62.5/125μm, 500MHz*km)

Single-mode:

1000BaseLX

0 to 10 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))

1000BaseLHX

0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))

1000BaseZX

0 to 80 km, 1550 nm (9/125μm, 19 PS/(nm*km))

Multi-mode:

100BaseFx

0 to 5 km, 1300 nm (50/125μm, 800MHz*km)

0 to 4 m, 1300 nm (62.5/125μm, 500MHz*km)

Single-mode:

100BaseFx

0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))

The concept behind the LC port and cable is quite straightforward.

Suppose you are connecting devices I and II. Unlike electrical signals,

optical signals do not require a circuit in order to transmit data.

Consequently, one of the optical lines is used to transmit data from device

I to device II, and the other optical line is used to transmit data from

device II to device I, for full-duplex transmission.

Remember to connect the Tx (transmit) port of device I to the Rx (receive)

port of device II, and the Rx (receive) port of device I to the Tx (transmit)

port of device II. If you make your own cable, we suggest labeling the two

sides of the same line with the same letter (A-to-A and B-to-B, as shown

below, or A1-to-A2 and B1-to-B2).

LC-Port Pinouts

LC-Port to LC-Port Cable Wiring

ATTENTION

This is a Class 1 Laser/LED product. To avoid

causing serious

damage to your eyes, do not stare directly into the Laser Beam.

Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power

sources. If one power source fails, the other live source acts as a backup,

and automatically supplies all of the EDS’s power needs.

- 10 -

LED Indicators

The front panel of the Moxa EtherDevice Switch contains several LED

indicators. The function of each LED is described in the table below.

LED

Color

State

Description

PWR1 AMBER On Power is being supplied to power

input P1

Off

Power is not being supplied to power

input P1.

PWR2 AMBER On

Power is being supplied to power

input P2

Off

Power is not being supplied to power

input P2.

100M GREEN

TP port’s 100Mbps link is active.

Blinking Data is being transmitted at

10/100Mbps.

Off

TP port’s 100Mbps link is inactive.

10/100M AMBER

TP port’s 10/100Mbps link is active.

Blinking

Data is being transmitted at

10/100Mbps.

Off

TP port’s 10/100Mbps link is inactive.

1000M GREEN

TP port’s 1000 Mbps link is active.

Blinking

Data is being transmitted at 1000

Mbps.

Off

TP port’s 100 Mbps.

Auto MDI/MDI-X Connection

The Auto MDI/MDI-X function allows users to connect the EDS’s

10/100/1000BaseT(X) ports to any kind of Ethernet device, without

paying attention to the type of Ethernet cable being used for the

connection. This means that you can use either a straight-through cable

or cross-over cable to connect the EDS to Ethernet devices.

Triple Speed Functionality and Switching

The EDS’s 10/100/1000 Mbps RJ45 switched port auto negotiates with

the connected device for the fastest data transmission rate supported by

both devices. The EDS is a plug-and-play device, so software

configuration is not required at installation or during maintenance.

The half/full duplex mode for the RJ45 switched ports is user dependent

and changes (by auto-negotiation) to full or half duplex, depending on

which transmission speed is supported by the attached device.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Handbuch

Moxa Technologies

Moxa Technologies ioLogik E1242 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004-HSPA Bedienungsanleitung

Moxa Technologies

Moxa Technologies MAR-2000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NSwitch Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-505A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-810 Series Handbuch

Moxa Technologies

Moxa Technologies NPort IA5150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7728 Handbuch

Moxa Technologies

Moxa Technologies SDS-3008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-4900 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8112-LX-STK Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C-EU Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-305-M12 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Handbuch

Moxa Technologies

Moxa Technologies EDS-405 Bedienungsanleitung

Moxa Technologies

Moxa Technologies AWK-4121 Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NAT-102 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung