Moxa Technologies TSN-G5000 Series Bedienungsanleitung

P/N: 1802050080011

*1802050080011*

TSN-G5000 Series

Quick Installation Guide

Moxa Industrial Managed Ethernet Switch

Version 1.0, June 2020

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Package Checklist

The TSN-G5000 Series is shipped with the following items. If any of

these items are missing or damaged, please contact your customer

service representative for assistance.

•1 TSN-G5000 Series industrial Ethernet switch

•1 RJ45 to RS-232 9-pin female console cable

•1 Quick installation guide (printed)

•1 Warranty card

•2 Terminal blocks

Default Settings

•Default IP address: 192.168.127.253

•Default Subnet Mask: 255.255.255.0

•Default User Name: admin

•Default Password: moxa

TSN-G5000 Series Panel Layout

TSN-G5004

- 3 -

TSN-G5008-2GTXSFP

1. USB storage port (type A, currently disabled)

2. Console port (RJ45, RS-232)

3. LED indicators x 5 (STATE, FAULT, PWR1, PWR2, SYNC)

4. Ethernet ports x 4 (8 for TSN-G5008), (RJ45,

10/100/1000BaseT(X))

5. LED indicator for 1000BaseT(X)

6. LED indicator for 10/100BaseT(X)

7. Ethernet ports x 2 (SFP, 100/1000BaseSFP)

8. Rubber cover for reset button and microSD card slot (currently

disabled)

9. Grounding screw (chassis ground)

10. Relay output (terminal block)

11. Power inputs x 2 (terminal block)

12. Digital input (terminal block)

13. DIN-rail mounting kit

14. Screw holes reserved for DIN-rail kit side mounting

15. Model side label (multiple product information included)

- 4 -

Dimensions

TSN-G5004

TSN-G5008-2GTXSFP

Unit: mm (inch)

- 5 -

DIN-Rail Mounting

There are two options for DIN-rail mounting that can be used for the

TSN-G5000 Series. Option 1 is the default type when shipped.

Option 1 (default):

When shipped, the metal DIN-rail mounting kit is fixed to the back

panel of the TSN-G5000 Series. Mount the TSN-G5000 Series on the

corrosion-free mounting rail that adheres to the EN 60715 standard.

Suggested Installation Method

Step 1—Insert the upper lip

of the DIN

-rail kit into the

mounting rail.

Step

2—Press the TSN-

G5000 Series towards the

mounting rail until it snaps

into place.

Suggested Removal Method

Step 1—Pull down the latch

on the DIN

-rail kit with a

screwdriver.

Steps

2 & 3—Slightly pull

the TSN

-G5000 Series

forward and lift up to remove

it from the mounting rail.

- 6 -

Option 2 (when side cabling is needed):

The metal DIN-rail mounting kit can be fixed to the side panel of the

TSN-G5000 Series. Mount the TSN-G5000 Series on the corrosion-free

mounting rail that adheres to the EN 60715 standard.

Default Installation

Side Installation

Suggested Installation Method

Step 1—Detach the metal DIN-rail mounting kit from the back panel

and attach it to the side panel, vertically as indicated in the figure

below.

Step 2—Insert the upper lip of the

DIN

-rail kit into the mounting rail.

Step

3—Press the TSN-G5000

Series towards the mounting rail

until it

snaps into place.

- 7 -

Suggested Removal Method

Step 1—Pull down the latch on the

DIN

-rail kit with a screwdriver.

Steps

2 & 3—Slightly pull the TSN

G5000 Series forward and lift up to

remove it from the mounting rail.

NOTE

Screws that are used to fix the DIN-rail kit on the TSN-G5000

Series should be securely fastened before mounting on the

mounting rail. Please make sure that if you remove the DIN

-rail

kit, it must be securely fastened when it is reattached.

Wall-mounting

For some applications, you will find it convenient to mount your TSN-

G5000 Series on the wall, as illustrated below.

Step 1—Remove the aluminum DIN-rail attachment plate from the

TSN-G5000 Series rear panel, and then attach the wall mount plates,

as shown in the diagram below.

- 8 -

Step 2—Mounting the TSN-G5000 Series on the

wall requires

four screws. Use the switch, with

wall mount plates attached, as a guide to mark

the correct locations of the

four screws. The

heads of th

e screws should be less than 6 mm in

diameter, and the shafts should be less than 3.5

mm in diameter, as shown in the figure at the

right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into

one of the keyhole

-shaped apertures of the wall mounting

plates.

Do not screw the screws in all the way—leave about 2 mm to allow

room for sliding the wall mount panel between the wall and the screws.

Step 3—Once the screws are fixed in the

wall, insert the four screw heads through

the large parts of the keyhole

-shaped

apertures, and then slide

the TSN-G5000

Series

downwards, as indicated on the

right

. Tighten the four screws for added

stability.

ATTENTION

Safety First!

External metal parts are hot. Take necessary precautions if it is

necessary to touch.

ATTENTION

In order to ensure

reliable operations, please make sure the

operating temp

erature

of the environment does not exceed the

spec

ifications. When mounting a TSN-G5000 Series with other

operating units in a cabinet without forced ventilation,

minimum

of 5 cm space on both the left and right of

the switch

is recommended.

- 9 -

Wiring Requirements

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Mox

a TSN-G5000 Series. Calculate the maximum

possible current in each power wire and common wire. Observe

all electrical codes dictating the maximum current allowable for

each wire size. If the current goes above the maximum ratings,

the wiring could overheat, causing serious damage to your

equipment.

Be sure to read and follow these important guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires

with different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring that shares similar electrical characteristics can be

bundled together.

•You should separate input wiring from output wiring.

•We advise that you label the wiring to all devices in the system.

Grounding the TSN-G5000 Series

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the ground screw (chassis ground) to the grounding surface prior to

connecting devices. The grounding screw is located on the top panel of

the TSN-G5000 Series.

ATTENTION

This product is intended to be mounted onto a well

-grounded

mounting surface, such as a metal panel.

- 10 -

Suggested Wire Type for Wiring Relay Contact

(R), Digital Input (DI) and Power Inputs (P1/P2)

The switch includes two 4-pins, 3.5 mm pin-pitch terminal blocks. The

following includes suggestions for wiring the relay contact (R), digital

input (DI) and power inputs (P1/P2) for the TSN-G5000 Series.

ATTENTION

We suggest using

a copper conductor with the cable type -

AWG (American Wire Gauge) 18

-24 and the corresponding pin

type cable terminals. In addition, the wire must be able to

withstand at least 105°C.

NOTE

We suggest the length of the pin type cable terminal is 8 mm.

In order t

o tighten the wire properly, please perform the

following three steps:

Step 1. Use a small flathead screwdriver

to press the push

in button beside each terminal of the terminal

block conn

ector. Step 2. Insert the wire. Step 3. Release the

screwdriver after the wire has been fully inserted. Please refer

to the diagram below.

Wiring the Relay Contact

The TSN-G5000 Series has one relay output for identifying when a

specific event has occurred (i.e., fault; see below). This relay output

uses the first contact out of the first 2-pin terminal on the TSN-G5000

Series' top panel.

Refer to the instructions and diagram below on how to connect the

wires to the terminal block connector, and how to attach the terminal

block connector to the terminal block receptor.

Step 1—Insert two wires into the relay position (see the diagram below

showing the top view) on the terminal to form an open circuit.

Step 2—To keep the relay wires from coming loose, use a small

flathead screwdriver to press the button beside each terminal of the

plastic terminal block connector in order to insert the wire tightly.

Release the screwdriver after the wire has been inserted properly.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-4900 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-305-M12 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Handbuch

Moxa Technologies

Moxa Technologies NPort IA5150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies SDS-3008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet TN-5516 Series Handbuch

Moxa Technologies

Moxa Technologies TN-5916 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G308 Handbuch

Moxa Technologies

Moxa Technologies SDS-3008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-810 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-405 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NSwitch Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004-HSPA Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1242 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Managed Ethernet Switch/Extender Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8112-LX-STK Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-G9010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Handbuch

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series Handbuch

Moxa Technologies

Moxa Technologies OnCell G4302-LTE4 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise