Moxa Technologies SDS-3008 Series Bedienungsanleitung

P/N: 1802300800011

*1802300800011*

SDS-3008 Series

Quick Installation Guide

Moxa’s Industrial Smart Ethernet Switch

Edition 2.0, March 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The SDS-3008 industrial smart Ethernet switch is the ideal device for IA

engineers and automation machine builders to make their networks

compatible with the vision of Industry 4.0. By breathing life into machines

and control cabinets, the smart switch simplifies daily tasks with its easy

configuration and easy installation. In addition, it is monitorable and easy

to maintain throughout the entire product life cycle.

The most frequently used automation protocols—including EtherNet/IP,

PROFINET, and Modbus/TCP—are embedded in the SDS-3008 to provide

enhanced operational performance and flexibility by making it

controllable and visible from automation HMIs. It also supports a range of

useful management functions, including IEEE 802.1Q VLAN, port

mirroring, SNMP, and warning by relay.

Package Checklist

The SDS-3008 is shipped with the following items. If any of these items

are missing or damaged, please contact your customer service

representative for assistance.

•1 SDS-3008 industrial smart Ethernet switch

•Protective caps for unused ports

•Quick installation guide (printed)

•Warranty card

Features

•8 10/100BaseT(X) Fast Ethernet ports

•Web-based graphical user interface for quick configuration and

management

•Supports EtherNet/IP, PROFINET, and Modbus/TCP industrial

protocol profiles for easy device integration and monitoring in

HMI/SCADA systems

•Supports IEEE 802.1D-2004 and IEEE 802.1w STP/RSTP for rapid

network redundancy

•IEEE 802.1Q VLAN to ease network planning

•Unused port lock, SNMPv3 and HTTPS to enhance network security

•Role-based account management for self-defined administration

and/or user accounts

•ABC-02 automatic backup configurator for quick event log and

configuration backup. Can also enable quick device change over and

firmware upgrade

•Automatic warning by exception through relay output

•Local log and the ability to export inventory files simplify inventory

management

Default Settings

•Default IP address: 192.168.127.253

•Default Subnet Mask: 255.255.255.0

•Default Usernames: admin, user

•Default Password: moxa

- 3 -

SDS-3008 Panel Layout

1. 1 to 8 10/100BaseT(X) ports (bottom to top)

2. System status LEDs (top to bottom)

STATE LED indicator (Green), FAULT LED indicator (Red),

PWR1 LED indicator (Amber), PWR2 LED indicator (Amber)

3. 1 to 8 port status LEDs (bottom to top)

•LED lights in Green: 100 Mbps

•LED lights in Amber: 10 Mbps

4. Model side label (Multiple production information included)

•Default IP: 192.168.127.253

5. Model name

6. Latch of the DIN-rail mounting kit

7. Grounding screw (chassis ground)

8. 4-pin terminals for power inputs (P1/P2), relay output (R) and

digital input (DI)

NOTE: starting from the front side called first terminal

9. Reset button

10.

USB storage port (type A connector)

11.

DIN-rail mounting kit

12.

Screw hole (reserved for other DIN-rail mounting methods;

for more

information please see the DIN-Rail Mounting section)

- 4 -

Mounting Dimensions; unit = mm (inches)

DIN-Rail Mounting

There are 2 options for DIN-rail mounting that can be adopted on a

SDS-3008. Option 1 is the default type when shipped.

Option 1 (Default):

When shipped, the metal DIN-rail mounting kit is fixed to the back panel

of the SDS-3008. Mount the SDS-3008 on the corrosion-free mounting

rail that adheres to the EN 60715 standard.

Suggested Installation Method

STEP 1—Insert the upper lip of

the DIN

-rail kit into the

mounting rail.

STEP 2

—Press the SDS-3008

towards the mounting rail until it

snaps into place.

- 5 -

Suggested Removal Method

STEP 1—Pull down the latch on

the DIN

-rail kit with a

screwdriver.

STEP

S 2 & 3—Slightly pull the

SDS

-3008

forward and lift up to

remove it from the mounting

rail.

Option 2 (when side cabling is needed):

The metal DIN-rail mounting kit can be fixed to the side panel (mold side)

of the SDS-3008 (horizontal or vertical). Mount the SDS-3008 on the

corrosion-free mounting rail that adheres to the EN 60715 standard.

Suggested Installation Method

STEP 1—Detach the metal DIN-rail mounting kit from the back panel and

attach it to the side panel (mold side) in either the horizontal or vertical

direction as indicated in the figure below.

- 6 -

STEP 2—Insert the upper lip of the

DIN

-rail kit into the mounting rail.

STEP 3

—Press the SDS-3008 towards

the mounting rail until it snaps into

place.

Suggested Removal Method

STEP 1—

Pull down the latch on the

DIN

-rail kit with a screwdriver.

STEP

S 2 & 3—Slightly pull the

SDS

-3008 forward and lift up to

remove it from the mounting rail.

NOTE

Screws that are used to fix the DIN-rail kit on the SDS-3008

should be

securely fastened before mounting on the mounting

rail. Please make sure

that if you remove the DIN-rail

, it must be

securely fastened when it is reattached.

ATTENTION

In order to

ensure reliable operations, please make sure the

operating temp. of the environment

does not exceed the spec.

When

mounting a SDS-3008 with other operating units in a

cabinet without forced ventilation,

minimum spacing of 3cm on

both sides and above/below the switch is recommended.

Wiring Requirements

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa

Industrial Smart Ethernet Switch.

Calculate the

maximum possible current in each power wire and common wire.

Observe all electrical codes dictating the maximum current

allowable for each wire size.

If the current goes above the

maximum ratings, the wiring could overheat, causing serious

damage to your equipment.

- 7 -

Be sure to read and follow these important guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•You should separate input wiring from output wiring.

•We advise that you label the wiring to all devices in the system.

Grounding the Industrial Smart Ethernet Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw (chassis ground) to the grounding surface prior to

connecting devices.

ATTENTION

This product is intended to be mounted onto a well

-grounded

mounting surface, such as a metal panel.

Suggested Wire Type for Wiring Relay Contact (R),

Digital Input (DI) and Power Inputs (P1/P2)

The switch includes two 4-pins 3.5mm pin-pitch terminal blocks. When

wiring the relay contact (R), digital input (DI) and power inputs (P1/P2)

for the SDS-3008, we suggest using the cable type - AWG (American Wire

Gauge) 18-24 and the corresponding pin type cable terminals.

NOTE

The wire must be able to withstand at least 105℃and the torque

value should be 4.5 lb-in (0.51 N-m).

- 8 -

NOTE

We suggest the length of the pin type cable terminal is 8 mm.

n order to tighten the wire properly,

①

use a small flathead

screwdriver to press the push

-in button beside

each terminal of

the terminal block connector before and during

②

inserting the

wire.

③Release the screwdriver after the wire has been fully

inse

rted. Please refer to the diagram below.

Wiring the Relay Contact

The SDS-3008 has one relay output for identifying when a specific event

has occurred (i.e., fault; see below). This relay output uses the first two

contacts out of the first 4-pin terminal on the SDS-3008's top panel.

Refer to the instructions and diagram below on how to connect the wires

to the terminal block connector, and how to attach the terminal block

connector to the terminal block receptor.

STEP 1—Insert two wires into the relay position (see the diagram below

showing the top view) on the terminal to form an open circuit.

STEP 2—To keep the relay wires from coming loose, use a small flathead

screwdriver to press the button beside each terminal of the plastic

terminal block connector in order to insert the wire tightly. Release the

screwdriver after the wire has been inserted properly.

STEP 3—Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the SDS-3008's top panel.

FAULT:

The two relay contacts of the 4-pin terminal block connector can be used

to indicate that a user-configured event has occurred. The two wires

attached to the relay contacts will form an open circuit when a

user-configured event is triggered. If a user-configured event does not

occur, the circuit remains closed as the relay itself is closed. Examples of

user-configured events include port link-down and power input ON/OFF.

For more details about user-configured events, please refer to the

SDS-3008 user manual.

- 9 -

NOTE

The relay output of the SDS-3008 reflects a potential-free,

normally opened solid

-state relay. Therefore, not only when

user

-configured events are triggered but also when there is no

power supply to the switch

it will open. To indicate a fault has

occurred

one

can integrate the relay contact on the smart switch

with an external alarming system circuit so that the status of

user

-configured events or no power supply can be monitored.

example is given in the diagram below w

here the buzzer will

sound when

user-configured events happen.

Wiring the Digital Input

The SDS-3008 has one set of digital inputs (DI). The DI consist of two

contacts of the second 4-pin terminal block on the SDS-3008’s top panel,

and the other 2 contacts are used for the power 2 (P2) DC inputs.

Refer to the instructions and diagram (top view) below on how to connect

the wires to the terminal block connector, and how to attach the terminal

block connector to the terminal block receptor.

STEP 1: Insert the negative (ground)/positive DI wires into the

respective ┴/I terminals.

STEP 2: To prevent the DI wires from coming loose, use a small flathead

screwdriver to press the button beside each terminal of the plastic

terminal block connector in order to insert the wire tightly. Release the

screwdriver after the wire has been properly inserted.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the top panel of the

SDS-3008.

- 10 -

Wiring the Redundant Power Inputs (12/24/48

VDC)

The SDS-3008 has two sets of power inputs–power input 1 (PWR 1/P1)

and power input 2 (PWR 2/P2). The top view of the terminal block

connector and the positions of the power inputs are shown below.

Take the following steps to wire the redundant power inputs:

STEP 1: Insert the Positive/Negative DC wires into the V1+/V1- terminal

for PWR 1 and/or V2+/V2- terminal for PWR 2.

STEP 2: To prevent the DC wires from coming loose, use a small flathead

screwdriver to press the button beside each terminal of the plastic

terminal block connector in order to insert the wire tightly. Release the

screwdriver after the wire has been properly inserted.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the top panel of the

SDS-3008.

ATTENTION

Before connecting the SDS

3008 to the DC power inputs, ensure

the DC power supply voltage is stable and of a correct level and

polarity.

Communication Connections

Each SDS-3008 smart Ethernet switch has 2 types of communication

ports:

•1 USB storage port (type A connector)

•8 10/100BaseT(X) Fast Ethernet ports

USB Storage Connection

The SDS-3008 has one USB storage port (type A connector; see the

diagram below for pinout assignments) on the front panel. Use Moxa’s

ABC-02-USB automatic backup configurator to connect to the

SDS-3008's USB storage port in order to perform configuration backup,

firmware upgrade, or system log file backup.

USB Storage Port (Type A Connector) Pinouts

Description

VCC (+5V)

D– (Data -)

D+ (Data+)

GND (Ground)

Andere Handbücher für SDS-3008 Series

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8112-LX-STK Bedienungsanleitung

Moxa Technologies

Moxa Technologies SDS-3008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-G9010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7528 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-305-M12 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Handbuch

Moxa Technologies

Moxa Technologies TSN-G5000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies SR3000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-505A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice Switch EDS-G205 Handbuch

Moxa Technologies

Moxa Technologies EDS-408A Handbuch

Moxa Technologies

Moxa Technologies MAR-2000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4PoE Handbuch

Moxa Technologies

Moxa Technologies EDS-210A-1GTX-1GSFP-4SFP Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort IA5150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet Bedienungsanleitung

Moxa Technologies

Moxa Technologies NAT-102 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-8010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise