National Instruments PXIe-5632 Bedienungsanleitung

GETTING STARTED GUIDE

NI PXIe-5632

8.5 GHz Full Two-Port Vector Network Analyzer

Note Before you begin, install and configure your chassis and controller.

This document explains how to install, configure, and test the NI PXIe-5632 (NI 5632). The

NI 5632 is a 8.5 GHz, 2-port vector network analyzer (VNA) with support for full S-parameter

measurements. The NI 5632 ships with the NI-VNA instrument driver, which you can use to

program the device.

To access NI 5632 documentation, navigate to Start»All Programs»National Instruments»

NI-VNA»Documentation.

The specifications document for your device is installed with the driver software. Refer to

ni.com/manuals for the most recent specifications for your device.

Caution The protection provided by this product may be impaired if it is used in a

manner not described in this document.

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

Verifying the System Requirements......................................................................................... 2

Unpacking the Kit.....................................................................................................................2

Verifying the Kit Contents................................................................................................ 3

Preparing the Environment....................................................................................................... 4

Installing the Software.............................................................................................................. 5

Installing the NI 5632............................................................................................................... 5

Connecting Signals........................................................................................................... 7

Configuring the NI 5632 in MAX...........................................................................................11

Programming the NI 5632...................................................................................................... 13

NI-VNA Examples......................................................................................................... 13

Making Uncalibrated Measurements with the NI 5632..........................................................14

Calibrating the NI 5632.......................................................................................................... 14

Making Calibrated Measurements with the NI 5632..............................................................15

Troubleshooting...................................................................................................................... 16

What Should I Do if the Module Fails the Self-Test?.....................................................16

Why Is the ACCESS LED Off When the Chassis is On?...............................................16

What Should I Do if the NI 5632 Doesn't Appear in MAX?..........................................16

Where to Go Next................................................................................................................... 18

Worldwide Support and Services............................................................................................18

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits are designed to provide reasonable protection against harmful interference when the

product is operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments

could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution To ensure the specified EMC performance, the length of all I/O cables

must be no longer than 3 m (10 ft).

Verifying the System Requirements

To use the NI-VNA instrument driver, your system must meet certain requirements.

For more information about minimum system requirements, recommended system, and

supported application development environments (ADEs), refer to the product readme, which

is available on the driver software media or online at ni.com/updates.

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Notify NI if the device appears damaged in any way. Do not install a damaged device.

3. Visually ensure that the inner and outer center conductors of PORT 1 and PORT 2 are not

damaged and are centered in the middle of the outer connector conductor.

4. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

2| ni.com | NI PXIe-5632 Getting Started Guide

Verifying the Kit Contents

Figure 1. NI 5632 Kit Contents

234

5678

1. NI PXIe-5632 Vector Network Analyzer device

2. SMA Driver Bit, part number 190487A-01

3. 1/8 in. Combination Phillips/Flathead Screwdriver,

part number 772006-01

4. NI-VNA Driver Software DVD

5. Read Me First: Safety and Electromagnetic

Compatibility

6. Maintain Forced-Air Cooling Note to Users

7. NI PXIe-5632 Getting Started Guide (this

document)

8. NI 5632 Calibration Certificate

Other Equipment

There are several required items not included in your device kit that you need to operate the

NI 5632. Your application may require additional items not included in your kit to install or

operate your device.

Required Items

• A PXI Express chassis and chassis documentation. The NI PXIe-1075 chassis is one

available option for your device. For more information about compatible chassis options,

refer to ni.com.

• An embedded controller or MXI controller system that meets the system requirements

specified in this guide and chassis documentation.

• 0.9 N · m (8 in-lb) torque wrench

Optional Items

• PXI Chassis Slot Blocker kit (NI part number 199198-01)

• The following accessories available on the NI 5632 product page at ni.com/products:

NI PXIe-5632 Getting Started Guide | © National Instruments | 3

Table 1. NI 5632 Accessories

Accessory Part Number

Manual VNA Calibration Kit, K-Type 781587-01

Manual VNA Calibration Kit, N-Type 781588-01

Automatic VNA Calibration Kit, K-Type, Male-Female, 70 KHz to 9 GHz 782364-01

Phase-Equal Precision Adapter Kit, K-Type 781595-01

Phase-Equal Precision Adapter Kit, N-Type 781596-01

Precision Coaxial Cable, 0.6 m, K-Type, Male-Male 781607-01

Precision Coaxial Cable, 0.6 m, K-Type, Male-Female 781608-01

Precision Coaxial Cable, 0.6 m, K-Type Male to N-Type Male 781609-01

Precision Coaxial Cable, 0.6 m, K-Type Male to N-Type Female 781610-01

Calibrated 5/16" Torque Wrench, 8 in-lbs (0.9 Nm) 781615-01

Preparing the Environment

Ensure that the environment you are using the NI 5632 in meets the following specifications.

............................................................................Operating ambient temperature

(IEC-60068-2-1, IEC-60068-2-2)

0 °C to 55 °C

............................................................................Operating relative humidity

(IEC-60068-2-56)

10% to 90%, noncondensing

............................................................................Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient

temperature)

............................................................................Pollution Degree 2

Indoor use only.

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

Note Refer to the NI PXIe-5632 Specifications at ni.com/manuals for complete

specifications.

4| ni.com | NI PXIe-5632 Getting Started Guide

Installing the Software

You must be an Administrator to install NI software on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Insert the driver software media into your computer. The installer should open

automatically.

If the installation window does not appear, navigate to the drive, double-click it, and

double-click autorun.exe.

3. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

4. When the installer completes, select Restart in the dialog box that prompts you to restart,

shut down, or restart later.

Installing the NI 5632

Caution To prevent damage to the device caused by ESD or contamination, handle

the device using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the modules.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the modules.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4. Remove the black plastic connectors from all the captive screws on the module front

panel.

5. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

The NI 5632 can be placed in PXI Express peripheral slots or PXI Express Hybrid

peripheral slots.

NI PXIe-5632 Getting Started Guide | © National Instruments | 5

6. Touch any metal part of the chassis to discharge static electricity.

7. Ensure that the ejector handle is in the unlatched (downward) position.

8. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the device into the slot until it is fully inserted.

Figure 3. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Down (Unlatched) Position

9. Latch the module in place by pulling up on the ejector handle.

10. Secure the device front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

11. Cover all empty slots using filler panels or slot blockers to maximize cooling air flow.

12. Power on the chassis.

Related Information

Installing the Software on page 5

6| ni.com | NI PXIe-5632 Getting Started Guide

Connecting Signals

Use appropriate shielded cables to connect signals to the NI vector network analyzer to ensure

you achieve the best measurement accuracy possible.

Unsuitable cabling can adversely affect the vector error correction, producing unreliable and

misleading results. Precision coaxial cables are available for purchase from ni.com. Ensure

you take the following precautions when connecting signals to the NI 5632.

• Use phase-stable cables to make connections with the NI 5632. Phase-stable cables help

ensure that the reference plane remains stable across shifts in cable position after

calibration.

• Maintain placement of any accessories or cables that you attach to the NI 5632 to ensure

that the reference plane remains constant between calibration and measurement.

Tip You can also use phase-equal adapters after calibration to preserve the

reference plane.

The following figure shows an example of the reference plane for a male and female

connector.

Figure 4. Connector Reference Plane and Pin Depth

2 3

4 4

1. Reference Plane

2. Female Connector

3. Male Connector

4. Pin Depth

Related Information

Refer to the NI Vector Network Analyzers Help for more information about reference planes

and pin depth.

Direct Connections to the NI 5632

The NI 5632 is a precision RF instrument that is sensitive to ESD and transients. Ensure you

take the following precautions when making direct connections to the NI 5632 to avoid

damaging the device.

NI PXIe-5632 Getting Started Guide | © National Instruments | 7

Caution Apply external signals only while the NI 5632 is powered on. Applying

external signals while the device is powered off may cause damage.

• Ensure you are properly grounded when manipulating cables or antennas connected to the

NI 5632 PORT 1 or PORT 2 connector.

• If you are using noninsulated devices, such as a noninsulated RF antenna, ensure the

devices are maintained in a static-free environment.

• If you are using an active device, such as a preamplifier or switch routed to the NI 5632

PORT 1 or PORT 2 connector, ensure that there are no signal transients greater than the

RF and DC specifications for the device that are being generated and sourced to the

NI 5632 PORT 1 or PORT 2 connector.

NI 5632 Front Panel

The NI 5632 contains nine connectors and two LEDs.

Figure 5. NI PXIe-5632 Front Panel

NI PXIe-5632

300 kHz - 8.5 GHz Vector Network Analyzer

Dual Sources

PORT 1

SOURCE 1

SOURCE 2

LO OUT

PFI 0

TTL

SOURCE 2

OUT

ACCESS ACTIVE

+27 dBm MAX

50 VDC

+27 dBm MAX

0 VDC

+27 dBm MAX

0 VDC

+27 dBm MAX

0 VDC

+20 dBm MAX

50 VDC

+27 dBm MAX

0 VDC

+27 dBm MAX

50 VDC

ALL RF PORTS

ESD

SENSITIVE

50 VDC MAX

REF IN

SOURCE 1

OUT

PORT 2

8| ni.com | NI PXIe-5632 Getting Started Guide

Table 2. Device Front Panel Icon Definitions

Refer to the user documentation for required maintenance measures to ensure user

safety and/or preserve the specified EMC performance.

The signal pins of this product's input/output ports can be damaged if subjected to

ESD. To prevent damage, turn off power to the product before connecting cables and

employ industry-standard ESD prevention measures during installation, maintenance,

and operation.

Table 3. NI 5632 Front Panel Connectors

Connector Use

PORT 1 Input/output terminal for NI 5632 measurements.

SOURCE 1 IN Input terminal for the source 1 access loop.

SOURCE 2 IN Input terminal for the source 2 access loop.

REF IN Input terminal for an external reference signal for the NI 5632.

PFI 0 Input terminal for an external trigger signal.

LO OUT Output terminal for the NI 5632 local oscillator.

SOURCE 1 OUT Output terminal for the source 1 access loop.

SOURCE 2 OUT Output terminal for the source 2 access loop.

PORT 2 Input terminal for NI 5632 measurements.

NI PXIe-5632 Getting Started Guide | © National Instruments | 9

Table 4. NI 5632 LEDs

LED Indication

ACCESS Indicates the basic hardware status of the NI 5632.

OFF—The device is not yet functional.

AMBER—The device is being accessed. Accessed means that the device is being

communicated with over the PXI Express bus.

GREEN—The device is ready to be programmed by NI-VNA.

RED—The device has detected a hardware error, such as a hardware failure. The

LED remains red until the error condition is removed.

ACTIVE Indicates the state of the NI 5632.

OFF—The device is not yet functional.

AMBER—The device is armed and waiting for a trigger.

GREEN—The device has received a Start Trigger. This state also indicates that

the device is making a measurement.

RED—The device has detected a spurious error, such as when the PLL becomes

unlocked. The LED remains red until the error condition is removed.

Connector Care

The NI 5632 is a high-accuracy precision laboratory device and should be carefully handled.

Follow the precautions listed in this section when handling or connecting devices. Complying

with these precautions guarantees longer component life and lower equipment downtime

because of connector or device failure.

Tighten Connectors Without Rotating the Center Pin

Never tighten the connectors, adapters, or cables such that the center pin rotates. Damage

occurs to the mating plane surfaces if the center pin rotates.

Avoid Touching Connectors with Bare Hands

Avoid touching connector mating planes with bare hands. Natural skin oils and microscopic

dirt particles are difficult to remove.

Observe Pin Depth of Mating Connectors

Make sure to use the proper connectors to mate with the NI 5632. NI recommends that you use

precision or instrument or metrology grade Type-K, 2.92 mm, 3.5 mm, or SMA connectors.

10 | ni.com | NI PXIe-5632 Getting Started Guide

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments NI PXI-562 Series Bedienungsanleitung

National Instruments

National Instruments PXI-5661 Bedienungsanleitung

National Instruments

National Instruments FD-11603 Bedienungsanleitung

National Instruments

National Instruments PXIe-4162 Bedienungsanleitung

National Instruments

National Instruments NI 5102 Bedienungsanleitung

National Instruments

National Instruments PXIe-4136 Bedienungsanleitung

National Instruments

National Instruments NI 5734 Bedienungsanleitung

National Instruments

National Instruments PXIe-5774 Bedienungsanleitung

National Instruments

National Instruments NI 9263 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-1491 Bedienungsanleitung

National Instruments

National Instruments VirtualBench VB-8034 Bedienungsanleitung

National Instruments

National Instruments NI PXI-5122 Handbuch

National Instruments

National Instruments NI PXIe-4137 Handbuch

National Instruments

National Instruments PXIe-5763 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4138 Handbuch

National Instruments

National Instruments PXIe-5663E Bedienungsanleitung

National Instruments

National Instruments VRTS Bedienungsanleitung

National Instruments

National Instruments NI 9219 Bedienungsanleitung

National Instruments

National Instruments PXIe-4162 Bedienungsanleitung

National Instruments

National Instruments InsightCM Bedienungsanleitung

National Instruments

National Instruments NI USB-6008 Bedienungsanleitung

National Instruments

National Instruments USB-568 RF Series Bedienungsanleitung

National Instruments

National Instruments NI 5731 Series Bedienungsanleitung

National Instruments

National Instruments PXIe-5665 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung