National Instruments USB-568 RF Series Bedienungsanleitung

June 2010

374788B-01

GETTING STARTED GUIDE

NI RF Power Meters

This document explains how to install, configure, and set up the NI USB-5680/5681 RF power meters.

NI RF power meters make true RMS power measurements. The NI RF power meters ship with the

NI-568x instrument driver, which you can use to program the device.

For more information about the NI 5680/5681, refer to the NI RF Power Meters Help, which is located

at Start»All Programs»National Instruments»NI-568x»Documentation. Refer to the specifications

document that ships with the device for detailed specifications.

For the most current versions of specifications and other documentation, visit ni.com/manuals.

For the latest version of NI-568x, visit ni.com/updates.

Contents

Conventions ......................................................................................................................................... 1

1. Verifying the System Requirements ................................................................................................ 2

2. Unpacking ........................................................................................................................................ 2

3. Verifying the Kit Contents............................................................................................................... 2

Other Required Items................................................................................................................... 3

4. Installing the Software ..................................................................................................................... 3

5. Installing the Hardware.................................................................................................................... 3

6. Windows Device Recognition ......................................................................................................... 4

7. Connecting Signals .......................................................................................................................... 4

Connector Care and Handling...................................................................................................... 5

8. Programming the NI RF Power Meter............................................................................................. 6

NI-568x SFP ................................................................................................................................ 6

NI-568x Instrument Driver .......................................................................................................... 7

NI-568x Examples ....................................................................................................................... 7

Appendix A: Front and Back Panel ..................................................................................................... 7

Appendix B: Where to Go for Support ................................................................................................ 8

Conventions

The following conventions are used in this guide:

»The »symbol leads you through nested menu items and dialog box options to a final action.

The sequence File»Page Setup»Options directs you to pull down the File menu, select the

Page Setup item, and select Options from the last dialog box.

This icon denotes a tip, which alerts you to advisory information.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to avoid injury, data loss,

or a system crash. When this symbol is marked on a product, refer to the Read Me First: Safety

and Electromagnetic Compatibility for information about precautions to take.

NI RF Power Meters Getting Started Guide 2 ni.com

bold Bold text denotes items that you must select or click in the software, such as menu items and

dialog box options. Bold text also denotes parameter names.

italic Italic text denotes variables, emphasis, a cross-reference, or an introduction to a key concept.

Italic text also denotes text that is a placeholder for a word or value that you must supply.

monospace Text in this font denotes text or characters that you should enter from the keyboard, sections

of code, programming examples, and syntax examples. This font is also used for the proper

names of disk drives, paths, directories, programs, subprograms, subroutines, device names,

functions, operations, variables, filenames, and extensions.

NI 5680 Refers to the NI USB-5680 RF power meter.

NI 5681 Refers to the NI USB-5681 RF power meter.

Platform Text in this font denotes a specific platform and indicates the text following it applies only to

that platform.

1. Verifying the System Requirements

To use the NI-568x instrument driver, the system must meet certain requirements. For more information

about minimum system requirements, recommended system, and supported application development

environments (ADEs), refer to the NI-568x Readme. Before installing NI-568x, you can access this file

on the NI-568x software CD. After you install NI-568x, you can access this file at Start»All Programs»

National Instruments»NI-568x»Documentation.

2. Unpacking

Remove the NI RF power meter from the package and inspect it for loose components or any sign of

damage. Notify NI if the device appears damaged in any way. Do not install a damaged device.

Caution The NI RF power meter is a static-sensitive device. Always properly ground yourself and

the equipment when handling the NI RF power meter or connecting to it.

3. Verifying the Kit Contents

Verify that the kit contains the following items required to set up and use the NI RF power meter:

❑NI RF power meter with dust cap

Note The NI 5681 ships from the factory with a protective silicone cover already installed on the

device.

❑One of the following cables:

– NI 5680: USB 2.0 A to Mini-B cable

– NI 5681: USB 2.0 A to Latching Micro-AB cable

❑A precision Type-N to SMA adapter

❑NI-568x instrument driver software CD. The NI-568x CD also includes the NI RF Power Meters

Help and the NI-568x Readme. After you install the NI-568x driver, you can find these documents

at Start»All Programs»National Instruments»NI-568x»Documentation.

©National Instruments Corporation 3 NI RF Power Meters Getting Started Guide

❑Other included documents:

–NI RF Power Meters Getting Started Guide (this document)

– Specifications document for your device

– Calibration certificate for your device. Contact your local NI sales representative if you need

a PDF copy of this document.

– Read Me First: Safety and Electromagnetic Compatibility

Other Required Items

In addition to the kit contents, you need the following items:

❑1 N · m torque wrench

❑Desktop or laptop computer with its documentation and one available USB 2.0 or 1.1 compliant

slot

4. Installing the Software

You must install the NI-568x software before installing the NI RF power meter. Complete the following

steps to install the software:

1. (Optional) If you are developing an NI-568x application, install an ADE, such as LabVIEW or

LabWindows™/CVI™.

2. Install the latest service packs for your operating system.

3. Insert the NI-568x CD into the CD drive. The NI-568x installer should open automatically. If the

installation window does not appear, navigate to the CD drive, double-click the drive, and

double-click setup.exe.

4. Follow the instructions in the installation prompts. For troubleshooting information, contact

NI technical support or visit ni.com/support.

(Windows 7/Vista) Users may see access and security messages during installation. Accept the

prompts to complete the installation.

5. When the installer completes, a dialog box asks if you want to restart, shut down, or restart later.

Select Restart.

5. Installing the Hardware

Install the NI-568x software before installing the hardware.

Note If you connect the NI RF power meter to a PC or chassis before installing the software, the PC

or chassis will not recognize the NI RF power meter.

To install the NI RF power meter, connect the USB cable between the device and the PC. Refer to

Figure 1 for an example of a completed installation.

Note The STATUS LED next to the device USB connector lights green after the NI-568x software

is installed.

NI RF Power Meters Getting Started Guide 4 ni.com

Figure 1. NI USB Power Meter Installation

6. Windows Device Recognition

After you install the NI RF power meter, Windows automatically recognizes a new device. You will see

a Windows message appear in the Windows task bar that notifies you that a new device has been

installed. You do not need to take any further action for Windows to recognize your device.

Note During the Windows device recognition process, Windows assigns a COM number to your

device. You can see the COM number that was assigned to your device in Measurement &

Automation Explorer (MAX), under Devices and Interfaces.

7. Connecting Signals

Connect signals to the NI RF power meter hardware front panel Type-N connector to perform common

power measurements. You can also use the Type N-to-SMA adapter to make the signal connection.

Note You must zero the NI RF power meter before you take power measurements, particularly when

the device operates within the lower 20 dB dynamic range of the device. Zero the NI RF power meter

every time you connect it to a USB port. If you make frequent low-power measurements, check the

sensor zeroing often, and repeat as necessary.

1 PXI Chassis

2 USB Cable

3 STATUS LED

4 USB Connector

5 NI RF Power Meter

NI PXI-1042

ATUS

©National Instruments Corporation 5 NI RF Power Meters Getting Started Guide

The back panel LED indicates the status of the NI RF power meter. Refer to Table 1 for LED

information.

For more information about these common measurements, refer to the NI RF Power Meters Help.

Caution Always refer to the specifications document included with the NI RF power meter device

before connecting signals. Failure to observe the specified maximum signal ratings can cause shock,

a fire hazard, or damage to the devices connected to the NI RF power meter. NI is not liable for any

damage or injuries resulting from incorrect signal connections.

Caution Do not overtorque the connectors. Always use the specified torque wrench.

Figure 2. Connecting the NI RF Power Meter to an SMA Cable

Connector Care and Handling

The NI RF power meter is a high-quality precision laboratory device and should be carefully handled.

Follow the precautions listed in this section when handling or connecting these devices. Complying with

these precautions guarantees longer component life and lower equipment downtime due to connector or

device failure.

Avoid Touching Connectors with Bare Hands

Avoid touching connector mating planes with bare hands. Natural skin oils and microscopic dirt

particles are difficult to remove.

Table 1. Status LED Indication

LED Color Meaning

Green The NI RF power meter is connected to a computer or a chassis and

is functioning properly.

Yell ow An error has occurred or the firmware is being updated.

Off The NI RF power meter is not initialized.

1 TSMA-to-SMA Coaxial Cable 2 Precision Type-N to SMA Adapter 3 NI USB Power Meter

21 3

NI RF Power Meters Getting Started Guide 6 ni.com

Observe Pin Depth of Mating Connectors

Make sure to use the proper connectors to mate with the NI RF power meter. NI recommends that you

use precision or industrial grade Type-N connectors or that you use SMA connectors when using the

Type N-to-SMA adapter. Always check the pin depth of a connector before use to determine if they are

out of the specified range.

Avoid Lateral Pressure

Never put lateral pressure on the center pin of the connector.

Avoid Overtorquing Connectors

Do not overtorque connectors; doing so may damage the connector center pin. Always use a 1 N · m

torque wrench when tightening connectors. Never use pliers. Never tighten the connectors, adapters,

or cables such that the center pin rotates.

Avoid Mechanical Shock

Precision connectors are designed to withstand years of normal bench handling. Handle the connectors

carefully and avoid dropping them. Mechanical shock significantly reduces their service life.

Avoid Applying Excessive Power

The NI RF power meter is rated for a specific maximum continuous input power. Exceeding the

maximum input power level permanently damages the internal components.

Clean Connectors Carefully

Dirt and other contamination on the connector interfaces can affect the performance of the RF

components. To clean the connector interfaces, use only denatured alcohol as a cleaning solvent. Do not

use excessive amounts of alcohol, as this prolongs drying time. Use low-pressure compressed air to

remove foreign particles and to dry the connector. After cleaning, verify that the center pin has not been

bent or damaged.

Tip Most cotton swabs are too large to fit in the smaller connector types. In these cases, remove

most of the cotton and then twist the remaining cotton tightly. Ensure that the remaining cotton does

not become lodged in the connector, and verify that no cotton or other foreign material remains in the

connector after cleaning. Cotton swabs of the appropriate size can be purchased through a medical

or laboratory supply center.

Store Connectors Properly

When not in use, keep the connectors covered with the dust cap included in the NI RF power meter

shipping kit.

8. Programming the NI RF Power Meter

You can acquire data with the NI RF power meter by using the NI-568x soft front panel (SFP), or you

can control the NI RF power meter programmatically with an ADE using the NI-568x instrument driver.

In addition, you can run the NI-568x examples to demonstrate the functionality of the device.

NI-568x SFP

The NI-568x SFP is a software representation of a traditional benchtop power meter. Launch the

NI-568x SFP to use the NI RF power meter interactively. You can launch the NI-568x SFP from

Start»All Programs»National Instruments»NI-568x»NI-568x Soft Front Panel.

©National Instruments Corporation 7 NI RF Power Meters Getting Started Guide

NI-568x Instrument Driver

NI-568x features a set of operations and attributes that exercise all the functionality of the NI RF power

meter, including configuration, control, and other device-specific functions. Refer to the NI RF Power

Meters Help for information about using NI-568x in your applications.

NI-568x Examples

The NI-568x examples are instructional tools that demonstrate some of the functionality of the NI RF

power meter. You can use these examples separately or integrate them into your systems. NI-568x

includes examples for getting started and other power meter functionality. You can access NI-568x

examples at Start»All Programs»National Instruments»NI-568x»Examples.

Appendix A: Front and Back Panel

The NI 5680 front panel has one connector. The NI 5680 back panel has one USB port and the STATUS

LED. Refer to Figure 3 for an illustration of both panels of the device.

Figure 3. NI USB-5680 Front and Back Panel

The NI 5681 front panel has one connector. The NI 5681 back panel has one USB port, an external

trigger terminal, and the STATUS LED. Refer to Figure 4 for an illustration both panels of the device.

Figure 4. NI USB-5681 Front and Back Panel

1 Type-N Connector 2STATUSLED 3 Mini-B USB Port

1 Type-N Connector

2 STATUS LED

3 Mircro-AB USB 2.0 Port

4 External Trigger Terminal

STATUS

Front Panel Back Panel

1 2 3

Front Panel Back Panel

1 2 43

CVI, LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are trademarks of National Instruments

Corporation. Refer to the Trademark Information at ni.com/trademarks for other National Instruments trademarks. The mark LabWindows is used

under a license from Microsoft Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National

Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the

National Instruments Patent Notice at ni.com/patents.

Appendix B: Where to Go for Support

The National Instruments Web site is your complete resource for technical support. At ni.com/

support you have access to everything from troubleshooting and application development self-help

resources to email and phone assistance from NI Application Engineers.

A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European

Communities using the manufacturer’s declaration of conformity. This system affords the user

protection for electromagnetic compatibility (EMC) and product safety. You can obtain the DoC for

your product by visiting ni.com/certification. If your product supports calibration, you can

obtain the calibration certificate for your product at ni.com/calibration.

National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin,

Texas, 78759-3504. National Instruments also has offices located around the world to help address

your support needs. For telephone support in the United States, create your service request at

ni.com/support and follow the calling instructions or dial 512 795 8248. For telephone support

outside the United States, contact your local branch office:

Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020,

Brazil 55 11 3262 3599, Canada 800 433 3488, China 86 21 5050 9800,

Czech Republic 420 224 235 774, Denmark 45 45 76 26 00, Finland 358 (0) 9 725 72511,

France 01 57 66 24 24, Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737,

Italy 39 02 41309277, Japan 0120-527196, Korea 82 02 3451 3400, Lebanon 961 (0) 1 33 28 28,

Malaysia 1800 887710, Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466,

New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland 48 22 328 90 10,

Portugal 351 210 311 210, Russia 7 495 783 6851, Singapore 1800 226 5886,

Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197, Spain 34 91 640 0085,

Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222,

Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments PXIe-5667 Bedienungsanleitung

National Instruments

National Instruments NI 9219 Bedienungsanleitung

National Instruments

National Instruments NI 9263 Bedienungsanleitung

National Instruments

National Instruments PXI-5660 Bedienungsanleitung

National Instruments

National Instruments Module NI PXI-8250 Bedienungsanleitung

National Instruments

National Instruments NI Vision PCI-1409 Bedienungsanleitung

National Instruments

National Instruments NI 9227 Handbuch

National Instruments

National Instruments NI PXIe-4137 Handbuch

National Instruments

National Instruments PXIe-5630 Bedienungsanleitung

National Instruments

National Instruments VirtualBench VB-8034 Bedienungsanleitung

National Instruments

National Instruments NI 4350 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-5624R Bedienungsanleitung

National Instruments

National Instruments NI PXI-4070 Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

National Instruments

National Instruments TB-2725 Bedienungsanleitung

National Instruments

National Instruments PXIe-4136 Bedienungsanleitung

National Instruments

National Instruments NI 5911 Bedienungsanleitung

National Instruments

National Instruments PXIe-5603 Bedienungsanleitung

National Instruments

National Instruments PXI-4070 6 1/2 Digit FlexDMM Handbuch

National Instruments

National Instruments NI 9421 Bedienungsanleitung

National Instruments

National Instruments InsightCM Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4138 Handbuch

National Instruments

National Instruments FD-11605 Bedienungsanleitung

National Instruments

National Instruments BNC-2810 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung