Norac UC5 Topcon X30 Bedienungsanleitung
Goldacres
Active Wing Roll Control Option
Installation Manual
5466BC-GA
Printed in Canada
Copyright 2015 by NORAC Systems International Inc.
Reorder P/N: 5466BC-GA-INST Rev A (Goldacres Active Wing Roll Control Option)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.
Contents
1Introduction................................................................................................................ 1
2Kit Parts ...................................................................................................................... 2
3Hydraulic Installation ................................................................................................ 5
4Electrical Installation ................................................................................................. 8
5Wing Roll Cylinder Air Bleed Procedure................................................................ 9
6Cable Drawings ........................................................................................................ 10
1
1Introduction
Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This
system is manufactured with top quality components and is engineered using the latest
technology to provide operating reliability unmatched for years to come.
When properly used the system can provide protection from sprayer boom damage, improve
sprayer efficiency, and ensure chemicals are applied correctly.
Please take the time to read this manual completely before attempting to install the system. A
thorough understanding of this manual will ensure that you receive the maximum benefit from
the system.
Your input can help make us better! If you find issues or have suggestions regarding the parts
list or the installation procedure, please don’t hesitate to contact us.
Every effort has been made to ensure the accuracy of the information contained in
this manual. All parts supplied are selected to specially fit the sprayer to facilitate
a complete installation. However, NORAC cannot guarantee all parts fit as
intended due to the variations of the sprayer by the manufacturer.
Please read this manual in its entirety before attempting installation.
2
2Kit Parts
2.1 Kit Overview
Figure 1: UC5 Active Wing Roll Control Parts
3
2.2 Hydraulic Plumbing
Figure 2: UC5 Active Wing Roll Control Hydraulic Plumbing
NOTE: All other hydraulic hoses and fittings needed for this installation are supplied by
Goldacres.
4
2.3 List of Parts
Item Part Number Name Quantity
C10 43230-04 CABLE UC5 VALVE 2PIN DT TO 2PIN DT 2
H20 44978 WING ROLL CYLINDER W/POSITION SENSOR 1
M03 5466BC-AP-INST MANUAL INSTALLATION UC5 ACTIVE WING ROLL OPTION GOLDACRES 1
V02 44962D VALVE ASSEMBLY EXPANSION DPOC PROP DT 4 BOLT 1
Do not use high speed power tools/drills when installing hardware.
The use of dielectric grease is not recommended on any NORAC electrical
connections.
To ensure all stainless steel hardware does not gall or seize apply a light coating of
the supplied Permatex Anti-seize grease to all threaded parts upon installation.
Permatex Anti-seize lubricant is preferred, but other similar anti-seize products
may be used.
5
3Hydraulic Installation
Ensure all pressure has been bled from the system before disconnecting any lines
or fittings. Hydraulic pressure will exist on the wing tilt circuits unless the wings
are being supported by other means. The hydraulic installation may be performed
with the wings in transport position, resting on the ground or with the tilt cylinders
fully extended.
Component failure due to oil contamination is not covered under the NORAC UC5
system warranty. It is recommended that a qualified technician perform the
hydraulic installation.
3.1 Expansion Block Assembly
1. Remove the four 4MBP plugs from the 2 station valve block (Figure 3). Gently tap the
plugs with a hammer to loosen before attempting to remove.
2. Coat the four o-rings in hydraulic oil and install them into the expansion block. Ensure the
o-rings are seated properly.
3. Attach the expansion block to the 2 station block using the included spring washers and
bolts.
4. Tighten the bolts to 31 ft-lbs (42 Nm).
Figure 3: NORAC Expansion Block Assembly
6
3.2 Wing Roll Cylinder Mounting
1. Mount the wing roll cylinder (H20) to the boom as shown in Figure 4 with the cable end
pointing towards the right-hand wing (when looking from the rear of the sprayer). Tighten
mounting bolts to 60-70 ft-lb (81-95 Nm).
2. Route the wing roll cylinder sensor cable to the 8-way coupler (E11).
Figure 4: Wing Roll Cylinder and Valve Block Mounting
7
3.3 Hydraulic Plumbing
From this point on in the installation the booms will be inoperative until the
hydraulics are fully installed.
After the NORAC valve is mounted, the hydraulic hoses and fittings can be plumbed. The
plumbing for the hydraulic circuit is shown schematically in Figure 2.
NOTE: All other hydraulic hoses and fittings needed for this installation are supplied by
Goldacres.
1. Disconnect the tilt lower lines from the tees at the sprayer valve block.
2. Install two more tees onto the tees installed on the lower lines. Connect the sprayer lower
lines to the second set of tees.
3. Connect a hose between the free ends of the tees on the lower lines.
4. Disconnect the sprayer raise lines from the tees at the sprayer valve block.
5. Connect the free ends of the tees on the raise lines to the ports on the ends of the wing
roll cylinder.
6. Connect the sprayer raise lines to the second ports on the ends of the wing roll cylinder.
7. Connect the “A” port on the wing roll cylinder to the “A” port on the NORAC expansion
block.
8. Connect the “B” port on the wing roll cylinder to the “B” port on the NORAC expansion
block.
Andere Handbücher für UC5 Topcon X30
55
Inhaltsverzeichnis
Andere Norac Steuerungssystem Handbücher
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac SPRA-COUPE 7000 Series Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC5 HD12 Bedienungsanleitung
Norac
Norac PULSE UC5 Gebrauchs- und Pflegehandbuch
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4+ Apache 2010+ Bedienungsanleitung
Norac
Norac UC4 Total Control Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Kurzanleitung
Norac
Norac UC4 Total Control Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac John Deere 4720 Bedienungsanleitung
Norac
Norac UC5 Rogator 600 Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
