Olympus BX51 Bedienungsanleitung

INSTRUCTIONS

BX51

SYSTEM MICROSCOPE

A X 7 6 5 5

This instruction manual is for the Olympus System Microscopes Models BX51 and BX52. To ensure

the safety, obtain optimum performance and to familiarize yourself fully with the use of this micro-

scope, we recommend that you study this manual thoroughly before operating the microscope.

Retain this instruction manual in an easily accessible place near the work desk for future reference.

This publication is printed on 100% recycled paper

7 ASSEMBLY

— See this section for the replacement of the light bulb. —

BX51

CONTENTS

4-5

6-7

8-20

TRANSMITTED LIGHT BRIGHTFIELD OBSERVATION PROCEDURE

3-2 Focusing Block ...................................................................................................................................................................................... 11

1Voltage Indication 2Using the Light Intensity Preset Switch

3Using the Filters

21-23

24-25

26-27

28-30

Correct assembly and adjustments are critical for the microscope to exhibit its full performance. If you are going to assemble

the microscope yourself, please read section 7, “ASSEMBLY” (pages 28 to 30) carefully.

IMPORTANT — Be sure to read this section for safe use of the equipment. —

1 NOMENCLATURE

3 USING THE CONTROLS

3-1 Base ................................................................................................................................................................................................................. 8-10

3-3 Stage............................................................................................................................................................................................................ 12 - 14

3-4 Observation Tube ...................................................................................................................................................................... 15-17

3-5 Condenser .......................................................................................................................................................................................... 18-19

1Centering the Condenser

2Compatibility of Objectives and Condensers

3-6 Immersion Objectives ................................................................................................................................................................. 20

1Using Immersion Objectives

3-7 Objectives with Correction Collar ............................................................................................................................. 20

4 TROUBLESHOOTING GUIDE

5 SPECIFICATIONS

6 OPTICAL CHARACTERISTICS (UIS2/UIS Series)

PROPER SELECTION OF THE POWER SUPPLY CORD .................................................................. 31-32

1Replacing the Fine Adjustment Knob

2Adjusting the Coarse Adjustment Knob Tension 3Pre-focusing Lever

1Placing the Specimen 2 Adjusting the X- and Y-Axis Knob Tension

3Rotating the Stage 4Adjusting the Stage Height

1Adjusting the Interpupillar Distance

2 Adjusting the Diopter

3Using the Eye Shades

4 Using the Eyepiece Micrometer Disk

5Selecting the Light Path of the Trinocular Tube

6Adjusting the Tilt

1-3

BX51

IMPORTANT

SAFETY PRECAUTIONS (Fig. 1)

Fig. 1

Designated bulb 12V100WHAL (PHILIPS 7724)

12V50WHAL-L (LIFE JC)

This microscope employs a UIS2/UIS (Universal Infinity System) optical design, and should be used

only with UIS2/UIS eyepieces, objectives and condensers for the BX2 series. (Some of the modules

designed for the BX series and objectives/eyepieces for the UIS series are also usable. For details,

please consult Olympus or the catalogues.) Less than optimum performance may result if inappropriate

accessories are used.

1. After the equipment has been used in an observation of a specimen that

is accompanied with a potential of infection, clean the parts coming in

contact with the specimen to prevent infection.

· Moving this product is accompanied with the risk of dropping the

specimen. Be sure to remove the specimen before moving this

product.

· In case the specimen is damaged by erroneous operation, promptly

take the infection prevention measures.

· The product becomes unstable if its height is increased by an accessory

mounted on it. In this case, take anti-toppling measures to prevent the

specimen from being dropped when the product topples down.

2. Install the microscope on a sturdy, level table or bench so as not to block

the air vents on the underside of the base.

Do not place the microscope on a flexible surface, as this could result in

blocking the air vents and cause overheating or a fire.

3. The surfaces of the lamp housing on the rear of the microscope will

become extremely hot during operation. When installing the microscope,

make sure to allow ample free space (10 cm or more) around and in

particular above the lamp housing.

4. When installing the microscope, route the power cord away from the

lamp housing. Should the power cord come in contact with the hot lamp

housing, the power cord could melt and cause electric shock.

5. To avoid potential shock hazards and burns when replacing the light

bulb, set the main switch @ to “ ” (OFF) then disconnect the power

cord from the wall outlet in advance. Whenever you replace the bulb

during use or right after use, allow the lamp housing‚ and bulb to cool

before touching. (Fig. 1)

# The microscope also incorporate a fuse (this should be replaced by

the manufacturer or an authorized agent).

6. Always use the power cord provided by Olympus. If no power cord is

provided, please select the proper power cord by referring to the section

“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of

this instruction manual. If the proper power cord is not used, product

safety performance cannot be warranted.

7. Always ensure that the grounding terminal of the microscope and that

of the wall outlet are properly connected. If the equipment is not grounded,

Olympus can no longer warrant the electrical safety performance of the

equipment.

8. Never insert metallic objects into the air vents of the microscope frame

as this could result in electrical shock, personal injury and equipment

damage.

Symbol Explanation

Indicates that the surface becomes hot, and should not be touched with bare hands.

Before use, carefully read the instruction manual. Improper use could result in personal injury to

the user and/or damage to the equipment.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Warning engraving

position

Lamp housing

(Warning against high temperature)

Fig. 2

1Getting Ready

Safety Symbols

The following symbols are found on the microscope. Study the meaning of the symbols and always use the equipment

in the safest possible manner.

Warnings

Warning engraving is placed at parts where special precaution is required when handling and using the microscope.

Always heed the warnings.

1. A microscope is a precision instrument. Handle it with care and avoid

subjecting it to sudden or severe impact.

2. Do not use the microscope where it is subjected to direct sunlight, high

temperature and humidity, dust or vibrations. (For the operating condi-

tions, refer to section 5, “SPECIFICATIONS”.)

3. When moving the microscope, remove the specimen and modules that

may drop during transport and carefully carry it with the grasping part

on the rear of the arm and the base as shown in Fig. 2 (Weight: approx.

16 kg).

# Before transporting the microscope, be sure to remove the speci-

men, eyepieces and color glass filter so that they will not drop. Also

remove other modules attached to the microscope because they

increase the system weight.

# Damage to the microscope will occur if you grasp it by the stage,

coarse/fine adjustment knob or binocular section of the observa-

tion tube.

4. The BX51 series can be used with up to two intermediate attachments

(e.g. a U-CA magnification changer, U-EPA2 eyepoint adjuster, etc.). For

restrictions when using two intermediate attachments, make sure to read

the instruction manual provided with the respective intermediate attach-

ments.

# The microscope may become unstable when its height is increased

by mounting certain modules on it. In such a circumstance, take

measures to prevent the microscope from toppling down and

dropping the specimen.

BX51

2Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirty away using a commercially available blower and wipe

gently using a piece of cleaning paper (or clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks –– for example, electrical

equipment that is being switched on or off.

Also remember to always use it only in a well-ventilated room.

2. Do not attempt to use organic solvents to clean the microscope components other than the glass components. To clean

them, use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Do not disassemble any part of the microscope as this could result in malfunction or reduced performance.

4. When not using the microscope, keep it covered with a dust cover.

5. When disposing of the microscope, check the regulations and rules of your local government and be sure to observe

them.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with the requirements of directive 98/79/EC concerning in vitro diagnostic

medical devices. CE marking means the conformity to the directive.

3Caution

If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,

the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates that failure to follow the instructions in the warning could result in bodily harm to the

user and/or damage to equipment (including objects in the vicinity of the equipment).

# : Indicates that failure to follow the instructions could result in damage to equipment.

} : Indicates commentary (for ease of operation and maintenance).

NOMENCLATURE

Interpupillary distance

adjustment scale (Page 15)

Diopter adjustment ring

(Page 15)

Slide holder (Page 12)

Aperture iris diaphragm ring

(Page 19)

X-axis knob (Page 13)

Y-axis knob (Page 13)

Pre-focusing Lever (Page 11)

Filter mount (Page 9)

Field iris diaphragm ring

(Page 18)

Allen screwdriver

Condenser height

adjustment knob (Page 18)

Voltage indicator LED

Main switch (Page 1)

Light intensity preset

switch (Page 8)

Light intensity preset

adjustment screw

(Page 8)

Fine adjustment knob (Page 11)

Coarse adjustment knob (Page 11)

Coarse adjustment tension adjustment ring (Page 11)

Brightness adjustment knob (Page 8)

(Lamp voltage adjustment knob)

(accommodation position)

(Detachable)

} If you have not yet assembled the microscope, read section 7, “ASSEMBLY” (pages 28 to 30).

Transmitted light specification model BX51TF or microscope frame

Filter knobs (Page 9)

Optional filter knob (Page 9)

Light path selector knob (Page 16)

ND6, ND25 and LBD from the front to the rear

BX51

Transmitted/reflected light

switch

Transmitted light/reflected light specification model BX51TRF microscope frame

NOTE

*For the reflected illuminators and reflected lamp housings, please also refer to their instruction manuals.

The controls are identical to those of the transmitted light specification models except for the transmitted/

reflected light switch and the reflected light system (vertical illuminator, reflected lamp housing).

Reflected light illuminator*

· Universal illuminator

(BX-URA2)

· Fluorescence illuminator

(BX-RFA)

· Vertical illuminator

(BX-RLA2)

Reflected lamp housing*

· 100 W mercury burner housing

(U-LH100HG)

· 100 W mercury apo-burner housing

(U-LH100HGAPO)

· 75 W xenon lamp housing

(U-LH75XEAPO)

· 100 W halogen lamp housing

(U-LH100-3)

· System lamp housing

(U-ULH, halogen bulb specification)

(for exclusive use with

the halogen light source)

(Controls Used) (Page)

(P. 8)

Start observation.

(P. 16)

(P. 12)

(P. 13)

(P. 11)

(P. 15)

(P. 18)

(P. 19)

(P. 18)

(P. 9)

TRANSMITTED LIGHT BRIGHTFIELD OBSERVATION PROCEDURE

Set the main switch to “ I ” (ON) and adjust the

brightness.

@Main switch

²Brightness adjustment knob

Set the transmitted light

(BX51TRF only)

³Transmitted/reflected light

switch

Engage only the LBD filter. |LBD filter knob

Select the light path (trinocular tube). ƒLight path selector knob

Place the specimen on the stage. …Slide holder

†X-/Y-axis knobs

Engage the 10X objective in the light path. ‡Revolving nosepiece

Bring the specimen in focus. ŠCoarse/fine adjustment knobs

Adjust the interpupillary distance.

Adjust the diopter.

Adjust the light axis.

‰Binocular tube

‹Diopter adjustment ring

ŒCondenser height adjustment

knob

™Condenser centering knob

Adjust the aperture iris and field iris diaphragms. šAperture iris diaphragm ring

›Field iris diaphragm ring

Engage the objective to be used in the light path

and bring the specimen in focus.

‡Revolving nosepiece

ŠCoarse/fine adjustment knobs

Adjust the brightness. ²Brightness adjustment knob

Engage the required filters. œFilters

(P. 5)

(P. 9)

(P. 8)

(P. 11)

Andere Handbücher für BX51

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus FLUOVIEW FV300 Bedienungsanleitung

Olympus

Olympus DP21-SAL Benutzerhandbuch

Olympus

Olympus SZX16 Bedienungsanleitung

Olympus

Olympus BX51M Bedienungsanleitung

Olympus

Olympus SZ2-ILA Bedienungsanleitung

Olympus

Olympus FV3000 Bedienungsanleitung

Olympus

Olympus BXFM Bedienungsanleitung

Olympus

Olympus SLIDEVIEW VS200 Bedienungsanleitung

Olympus

Olympus SZX16 Installationsanleitung

Olympus

Olympus BHTU Bedienungsanleitung

Olympus

Olympus CHBS Bedienungsanleitung

Olympus

Olympus CX31 Bedienungsanleitung

Olympus

Olympus SZ3060 Bedienungsanleitung

Olympus

Olympus SZ-III Bedienungsanleitung

Olympus

Olympus CX21 Bedienungsanleitung

Olympus

Olympus U-DA Bedienungsanleitung

Olympus

Olympus FV5-LD405 Bedienungsanleitung

Olympus

Olympus BH2 Series Montageanleitung

Olympus

Olympus BX51-P Betriebsanleitung

Olympus

Olympus FH Bedienungsanleitung

Olympus

Olympus DP73 Bedienungsanleitung

Olympus

Olympus MX50A/T Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus K Betriebsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung