Olympus CX31-P Bedienungsanleitung

INSTRUCTIONS

CX31-P

POLARIZING MICROSCOPE

This instruction manual is for the Olympus Polarizing Microscopes Model CX31-P. To ensure the

safety, obtain optimum performance and to familiarize yourself fully with the use of this microscope,

we recommend that you study this manual thoroughly before operating the microscope. Retain this

instruction manual in an easily accessible place near the work desk for future reference.

A X 7 3 4 9

This publication is printed on 100% recycled paper

4-1 Microscope Frame .................................................................................................................................................................................8

CONTENTS

CX31-P

IMPORTANT — Be sure to read this first for safe use of the equipment. — 1-3

.................................................................. 15

1 MODULE NOMENCLATURE

2 CONTROLS

SUMMARY OF POLARIZED LIGHT OBSERVATION PROCEDURE

4 OPERATION

6-7

8-14

Correct assembly and adjustments are critical for the microscope to manifest its full performance. If you are going to

assemble the microscope by yourself, please read Chapter 9, “ASSEMBLY” (Pages 23 to 26). For the assemblies of the

modules for which instruction manuals are available, refer to their instruction manuals.

1 Turning the Lamp ON

3 Using the Filters

2Field Iris Diaphragm

4-2 Focusing Module ......................................................................................................................................................................................9

4-3 Observation Tube ........................................................................................................................................................................... 9-10

2Adjusting the Diopter

4Using the Eyepiece Micrometer Disk

1Placing Specimen on the Stage

4-4 Intermediate Tube for Polarizing Observation (U-PA) .......................................................................11

4-5 Rotary Stage ................................................................................................................................................................................................ 12

2Rotating the Stage

4-6 Condenser...................................................................................................................................................................................................... 13

1Centering the Field Iris Diaphragm 2Using the Aperture Iris Diaphragm

4-7 Immersion Objective ....................................................................................................................................................................... 14

1Adjusting the Coarse Adjustment Knob Rotation Tension

2Using the Simplified Pre-focusing Knob

1 Adjusting the Interpupillary Distance

3 Using the Eye Shades

1 Using the Bertrand’s Lens 2Using the Analyzer

2Centering the Rotary Stage1Cross-Nicol Adjustment

3Adjusting the Centering Adapter

for Objective

PROPER SELECTION OF THE POWER SUPPLY CORD .................................................................. 27-28

23-26

21-22

5 POLARIZED LIGHT OBSERVATION

5-1 Preparation ........................................................................................................................................................................................... 15-17

5-2 Orthoscopic Observation ......................................................................................................................................................... 18

5-3 Conoscopic Observation .......................................................................................................................................................... 18

15-18

6 SPECIFICATIONS

7 OPTICAL CHARACTERISTICS

8 TROUBLESHOOTING GUIDE

9 ASSEMBLY

CX31-P

IMPORTANT

SAFETY PRECAUTIONS

1. After the equipment has been used in an observation of a specimen that

is accompanied with a potential of infection, clean the parts coming in

contact with the specimen to prevent infection.

· When moving the microscope, be sure to remove the specimen to

prevent it from dropping and scattering, and hold the microscope

by the positions shown in Fig. 2 on the next page.

· In case the specimen is damaged by mistake, promptly take the action

for preventing infection.

· The microscope becomes unstable when its height is increased by

attached modules. In this case, be sure to take countermeasures for

preventing it from toppling down and dropping the specimen.

2. To avoid potential shock hazards and burns when replacing the lamp bulb, set

the main switch 1to “ ” (OFF) then disconnect the power cord from the wall

outlet in advance and, whenever you replace the bulb during use or right after

use, allow the lamp replacement cover 2and bulb to cool before touching.

3. Install the microscope on a sturdy, level table or bench so as not to block

the air vents on the underside of the base. Do not place the microscope

on a soft surface into which the microscope may sink, as this could result

in blocking the air vents and cause overheating or a fire.

4. Always use the power cord provided by Olympus. If no power cord is

provided, please select the proper power cord by referring to the section

“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of

this instruction manual. If the proper power cord is not used, product

safety performance cannot be warranted.

5. When installing the microscope, route the power cord away from the

microscope frame. Should the power cord come in contact with a hot

part, the power cord could melt and cause electric shock.

6. Always ensure that the grounding terminal of the microscope and that of the

wall outlet are properly connected. If the equipment is not grounded, Olympus

can no longer warrant the electrical safety performance of the equipment.

7. Never set the main switch 1to “ I ” (ON) while a metallic object is present

in the air vents of the microscope, as this could result in electrical shock,

personal injury and equipment damage.

8. After operation or in case of abnormality, be sure to disconnect the power

cord from the connector on the microscope or from the wall power outlet

Symbol Explanation

IIndicates that the surface becomes hot, and should not be touched with bare hands.

Fig. 1

Safety Symbols

The following symbols are found on the microscope. Study the meaning of the symbols and always use the equipment in

the safest possible manner.

Before use, carefully read the instruction manual. Improper use could result in personal injury to

the user and/or damage to the equipment.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

If the warning label is stained or peeled off, contact Olympus.

1Getting Ready

2Maintenance and Storage

Warning Label

A warning indication label is attached to every part where special precaution is required when handling and using the

microscope. Always heed the warnings.

Warning label position Bottom of microscope frame Warning against high tempera-

ture in lamp bulb replacement

1. A microscope is a precision instrument. Handle it with care and avoid

subjecting it to sudden or severe impact.

2. Do not use the microscope where it is subjected to direct sunlight, high

temperature and humidity, dust or vibrations. (For the operating condi-

tions, see chapter 6, “SPECIFICATIONS” on page 19.)

3. Always use the tension adjustment ring to adjust the rotation tension of

the coarse adjustment knob.

4. The microscope is ventilated by natural convection. Be sure to leave

enough spaces (10 cm or more) around it when installing it.

5. When carrying the microscope, hold it by the bottom of the base 1and

finger hook on the rear 2as shown on the left and carry carefully.

#To prevent damage, do not hold the microscope by the stage or

observation tube. Before carrying, remove the specimen and filters

to prevent them from dropping.

#If the microscope is displaced by sliding on the desktop, the rubber

feet may be damaged or separated from the bottom.

Fig. 2

1. Clean all glass components by wiping gently with gauze. To remove fingerprints or oil smudges, wipe with gauze slightly

moistened with a mixture of ether (70%) and alcohol (30%).

Since solvents such as ether and alcohol are highly flammable, they must be handled carefully. Be sure to keep

these chemicals away from open flames or potential sources of electrical sparks –– for example, electrical

equipment that is being switched on or off. Also remember to always use these chemicals only in a well-

ventilated room.

2. Do not attempt to use organic solvents to clean the microscope components other than the glass components. To clean

them, use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Do not disassemble any part of the microscope as this could result in malfunction or reduced performance.

4. When not using the microscope, ensure that the frame is cooled down and store it in a dry locker or cover it with

a dust cover.

CX31-P

The following symbols are used to set off text in this instruction manual.

: Indicates that failure to follow the instructions in the warning could result in bodily harm to the

user and/or damage to equipment (including objects in the vicinity of the equipment).

# : Indicates that failure to follow the instructions could result in damage to equipment.

}: Indicates commentary (for ease of operation and maintenance).

3Caution

If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with the requirements of directive 98/79/EC concerning in vitro diagnostic medical

devices. CE marking means the conformity to the directive.

MODULE NOMENCLATURE

?The modules shown below are merely the typical examples. For other applicable modules that are not shown, please

consult the latest catalogues or Olympus.

Eyepieces

· WHN10X

· WHN10X-H

· CROSS WHN10X

· WHB10X

· WHBX10X-H

Intermediate Tube for Polarizing

Observation

·U-PA

·U-OPA

· U-KPA

Rotary stage (Not detachable)

Polarized light condenser

Observation Tube

· U-BI30P

· U-TR30-2

· U-CBI30-2

· U-CTR30-2

Microscope Frame

· CX31PF

Centering Adapter for

Objective Lens

· U-CTAD (4-piece set)

Polarized Light Objective

· PlanN4X-P

· AchN10X/20X/40X/100XO-P

}Other applicable modules

· Mechanical Stage U-FMP

· Rotary Analyzer for Polarized Light U-AN360P-2

· Sensitive Tint Plate U-TP530

· Quarter-Wave Plate U-TP137

· Test Plate Adapter U-TAD

· Transmitted Light Analyzer U-ANT

· Gout Analyzer U-GAN

· Compensators (6 models)

CX31-P

CONTROLS

}If you have not yet assembled the microscope, read Chapter 9, “ASSEMBLY” (pages 23 to 26) first.

· The illustration shows the microscope together with the U-BI30P binocular observation tube for polarizing observation

U-PA intermediate tube for polarizing observation and U-CTAD centering adapter for objective lens.

Interpupillary distance scale (Page 9)

Diopter adjustment ring

(Page 9)

Bertrand’s lens engaging/

focusing knob (Page 11)

) : IN. ( : OUT.

Objective centering screws (Page 17)

Stage rotation clamping knob

Aperture iris diaphragm lever (Page 13)

Field iris diaphragm ring (Page 8)

Test plate/compensator insertion slot

Analyzer rotation assist knob

Provided on 2 positions.

Analyzer clamping knob (Page 11)

Analyzer engaging/rotation knob (Page 11)

) : IN.

( : OUT.

Simplified pre-focusing knob (Page 9)

Main switch (Page 8)

Light intensity adjustment knob

(Page 8)

Stage centering knobs

Provided on both sides

Fine adjustment knob (Page 9)

Coarse adjustment knob (Page 9)

Condenser height adjustment knob (Page 13)

Oscillation direction indications

A : Analyzer

P : Polarizer

Filter holder

For 45 mm filters.

Polarizer rotation knob (Page 15)

Condenser centering knobs

Provided on both sides

SUMMARY OF POLARIZED LIGHT OBSERVATION

PROCEDURE

}This chapter describes the procedure for polarized light observation using the U-PA intermediate tube for polarizing

observation. For the procedure using the U-OPA or U-KPA, refer to the instruction manual for the intermediate tube in use.

* The operations marked *are not required when the U-CTAD centering adapter for objective lens is not used.

(Controls Used) (Page)

Set the main switch to “ I ” (ON).

Disengage the Bertrand’s lens.

Disengage the analyzer.

Place the specimen on the stage.

Engage the reference objective in the light path.

Bring the specimen into focus.

Adjust the brightness.

Adjust the interpupillary distance.

Adjust the diopter.

Adjust the analyzer and polarizer oscillation directions.

Center the reference objective.

Center the stage.

Center other objectives.

Center the field iris diaphragm.

Engage the objective to be used in the light

path, engage the analyzer and/or Bertrand’s

lens according to the purpose of observation,

and bring the specimen into focus.

Start observation.

1 Main switch (P. 8)

2 Light intensity adjustment knob (P. 8)

Bertrand’s lens engaging/focusing knob

(P. 11)

4 Analyzer engaging/rotation knob (P. 11)

5Specimen holder

6 Revolving nosepiece

Coarse/fine focus adjustment knobs

(P. 9)

2 Light intensity adjustment knob (P. 8)

8Binocular tube (P. 9)

9 Diopter adjustment ring (P. 9)

4 Analyzer engaging/rotation knob (P. 11)

a Polarizer rotation knob (P. 15)

bObjective centering screws (P. 17)

cStage centering knob (P. 16)

d Field iris diaphragm ring (P. 8)

e Condenser height adjustment knob (P. 13)

f Condenser centering knob (P. 13)

bObjective centering screws (P. 17)

6 Revolving nosepiece

4 Analyzer engaging/rotation knob (P. 11)

Bertrand’s lens engaging/focusing knob

(P. 11)

7 Coarse/fine focus adjustment knobs (P. 9)

Adjust the aperture and field iris diaphragms. g Aperture iris diaphragm lever (P.13)

d Field iris diaphragm ring (P. 8)

Engage the required filters. h Filter holder (P. 8)

Adjust the brightness. 2 Light intensity adjustment knob (P. 8)

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus MX50A/T Bedienungsanleitung

Olympus

Olympus BHS Bedienungsanleitung

Olympus

Olympus SZX-DA Bedienungsanleitung

Olympus

Olympus CK2 Bedienungsanleitung

Olympus

Olympus SZX2-LTTR Bedienungsanleitung

Olympus

Olympus U-LGPS Bedienungsanleitung

Olympus

Olympus BHTU Bedienungsanleitung

Olympus

Olympus SZ-III Bedienungsanleitung

Olympus

Olympus BH2-6RE Bedienungsanleitung

Olympus

Olympus CHA Bedienungsanleitung

Olympus

Olympus U-D7RES Bedienungsanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus SZX-AR1 Bedienungsanleitung

Olympus

Olympus DSX1000 Bedienungsanleitung

Olympus

Olympus DP26 Bedienungsanleitung

Olympus

Olympus CKX41 Bedienungsanleitung

Olympus

Olympus SZX16 Installationsanleitung

Olympus

Olympus X-Tr Betriebsanleitung

Olympus

Olympus DP74 Bedienungsanleitung

Olympus

Olympus CKX31 Betriebsanleitung

Olympus

Olympus BX51M Bedienungsanleitung

Olympus

Olympus BX61WI Bedienungsanleitung

Olympus

Olympus BHTU-112 Bedienungsanleitung

Olympus

Olympus BX3-SSU Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung