Olympus BX3-SSU Bedienungsanleitung

INSTRUCTIONS

BX3-SSU

SCANNING STAGE WITH ULTRASONIC

This instruction manual is for the Olympus Scanning Stage with Ultrasonic Model BX3-SSU.

To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use of

the scanning stage with ultrasonic, we recommend that you study this manual thoroughly before

operating the microscope. In addition, be also sure to read the instruction manual for the BX63

microscope on which the scanning stage with ultrasonic is installed.

Retain this instruction manual in an easily accessible place near the work desk for future reference.

A X 7 9 3 4

In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment,

this symbol indicates that the product must not be disposed of as unsorted municipal waste, but

should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in your

country.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

Compliance

This device complies with the requirements of both directive 2004/108/EC concerning electromagnetic

compatibility and directive 2006/95/EC concerning low voltage. The CE marking indicates compliance

with the above directives.

IEC61326-1 defines two categories according to the location for use.

Class A: Equipment suitable for use in establishments other than domestic, and those directly con-

nected to a low voltage power supply network which supplies buildings used for domestic

purposes.

Class B: Equipment for use in domestic establishments, and in establishments directly connected to a

low voltage power supply network which supplies buildings used for domestic purposes.

This system is applied Class A. Some interference may occur if this system is used in domestic location.

BX3-SSU

CONTENTS

IMPORTANT -- Be sure to read this section for safe use of the equipment. -- 1,2

4,5

1 MODULE NOMENCLATURE

2 CONTROLS

3 OPERATION OF SCANNING STAGE WITH ULTRASONIC

1Turning the Power ON 2Moving the Stage

1Stage Center Plate IX-CP50/IX2-GCP

3Replacing the Fuses

2Stage Clips IX-SCL

4 OPTIONAL ACCESSORIES 7

nPROPER SELECTION OF THE POWER SUPPLY CORD............................................................ 13 ,14

5 SPECIFICATIONS

6 TROUBLESHOOTING GUIDE

7 ASSEMBLY

10-12

SAFETY PRECAUTIONS (Fig. 1)

IMPORTANT

}This manual pertains only to the information related to the scanning stage

with ultrasonic and associated modules.

Before using this instrument together with the BX63 microscope and

associated modules, make sure that you have carefully read their manuals

and understand how the system should be operated together.

To ensure the performance, we recommend that you have your

Olympus representative assemble and adjust the scanning

stage with ultrasonic.

1. Install the microscope on a level (inclination less than ±2°) surface on a

sturdy table or bench.

2. To prevent obstruction of the air vents 2on both sides of the control box

@ for BX3-SSU, always install it longitudinally and make sure to leave at

least 10 cm of free spaces around them.

Also, to prevent malfunction or electric shock, do not allow a wire or thin

object to enter the air vents.

When installing the BX3-CBH and the control box for BX3-SSU

side by side, always install the BX3-CBH on the left to enable

effective heat radiation.

3. Always use the power cord provided by Olympus. If no power cord is

provided, please select the proper power cord by referring to the section

“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this

instruction manual. If the proper power cord is not used, product safety

performance cannot be warranted.

4. Always ensure that the grounding terminal of the instrument and that of

the wall outlet are properly connected. If the equipment is not grounded,

Olympus can no longer warrant the electrical safety performance of the

equipment.

5. The power cord can be used to shut down the power supply in case of

emergency. To make this possible, place the power cord plug in an easily

accessible location.

Fig. 1

CAUTION

Safety Symbols

The following symbols are found on this system. Study the meaning of the symbols and always use the equipment in

the safest possible manner.

Symbol Explanation

Indicates a non-specific general hazard. Follow the description given after this symbol or in

instruction manual.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Indicates a potential fire hazard; when replacing fuses, be sure replacement fuses are of the

specified rating.

BX3-SSU

1Getting Ready

1. The scanning stage with ultrasonic is a precision instrument. Handle it with care and avoid subjecting it to sudden or

severe impact.

2. When the scanning stage with ultrasonic needs to be packaged for forwarding to a remote location, it should be clamped

using clamping hardware. Please contact Olympus (to obtain advice).

3. Do not use the instrument where it is subjected to direct sunlight, high temperature and humidity, dust or vibrations.

Also avoid using it in the following places.

(1) Near an air intake or outlet of an air conditioning facility, etc.

(2) Place subject to important vibrations or changes in temperature.

(3) Near a source (including equipment not manufactured by Olympus) of abnormal noise.

(4) Place subject to direct sunlight.

(5) Place exposed to excessive dust or high temperature/humidity.

(6) Near a ﬂammable substance (gasoline, lacquer thinner, alcohol, etc.).

4. Leave certain slack to the stage cable so that they are not over-tensioned when the stage is moved.

5. Do not touch this stage unless it needs to be stopped urgently. it should not be touched except for emergency stop

purpose in order to prevent the position information from being deviated. If this happens, turn the stage off then on

again.

Also note that the stage movement may become temporarily unsmooth after it has been moved by hand.

6. Whenever emergency stop is necessary during motorized movement, the stage can be stopped by holding it by hand.

7. Before replacing the fuse, be sure to set the main switch of the control box to “ ” (OFF) and unplug the power cord for

safety.

2Maintenance and Storage

1. To clean the parts, simply wipe them with a clean cloth. If a part is extremely dirty, do not use organic solvents but use a

soft cloth slightly moistened with a diluted neutral detergent.

2. Do not disassemble any part of the microscope except for the parts that are specified to be disassembled in this manual,

as this could result in malfunction or reduced performance.

3. Before disposing of this product, be sure to follow the regulations and rules of your local government.

3 Caution

If the instrument is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,

the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates a potentially hazardous situation which, if not avoided, may result in minor

or moderate injury or damage to the equipment or furniture in the surroundings. This

symbol is also used to warn against risky actions.

} : Indicates commentary (for ease of operation and maintenance).

CAUTION

1MODULE NOMENCLATURE

}To ensure the performance, we recommend that you have your Olympus representative assemble and adjust the scanning

stage with ultrasonic.

The modules marked *are not part of the scanning stage with ultrasonic product.

The control of the scanning stage with ultrasonic is possible from the U-MCZ controller, the touch-panel controller provided with

the BX63.

Microscope frame*

BX63F

Scanning stage with

ultrasonic

BX3-SSU

Control box*

BX3-CBH

Controller*

U-MCZ

XY controller

Provided with BX3-SSU.

Control box

Provided with BX3-SSU.

BX3-SSU

CONTROLS

Scanning Stage with Ultrasonic BX3-SSU * Attach the stage clips only in the two holes on the front side

of the stage. (Do not use the holes on the rear side to avoid

interference with the objectives.)

Stage clip attaching holes*

Total 4 holes.

Slide holder (Detachable)

For a slide glass sample.

Optional accessories

Stage clips

IX-SCL

Center plate with

50 mm hole

IX-CP50

Glass center plate

IX2-GCP

Supersonic stage control box (Provided with BX3-SSU)

Pilot lamp

Main switch

“ I”: ON. “ ”: OFF.

RS232C

connector

DRIVE connector

SENSOR connector

MCXY connector

TRIG-OUT connector

Power cord connector

Fuse box (P. 6)

XY controller (Provided with BX3-SSU)

Y-axis knob*

X-axis knob*

Coarse/fine selector button

Pushed in: Coarse adjustment.

Out position: Fine adjustment.

* The factory settings of the stage displacement per turn are 10 mm for the coarse adjustment and 0.2 mm for the fine

adjustment.

CAUTION

1. Open the [Menu] display by controlling the touch panel.

2. Tap the System Setting button @ to open the [System Setting] display.

3. Tap the [ECO, Others] tab 2and then tap the Auto Compensation

button 3.

4. When the auto compensation confirmation display appears, tap [OK] to

start auto compensation.

The stage moves automatically during the auto compensation

(for a few minutes). Do not touch the stage during the

movement.

5. When auto compensation completes, the touch panel screen shows the

completion message.

If the foreign substance is entered in the stage driving part,

the status may not be recovered by performing the Auto

Compensation. In this case, turn the power of BX3-SSU Control

Box to “ ” (OFF), and perform the Auto Compensation again

after moving the stage from front to back and from side to side

several times with a hand.

This stage is equipped with the Auto Compensation for the stage operation parameters to provide you the best operational

feeling to fit to your use environment.

If the stage operation parameters are displaced against your use environment, you may not obtain the best operational

feeling, such that the stage does not move smoothly, etc. In that case, perform the Auto Compensation of the stage

according to the following procedures to reset the stage operation parameters to the optimum value.

Before starting the auto compensation, install the stage on the BX63 and make sure nothing, including a

specimen, is placed on the stage.

Auto Compensation of the Stage

BX3-SSU

3OPERATION OF SCANNING STAGE WITH ULTRASONIC

Fig. 2

Fig. 3

Fig. 4

1Turning the Power ON (Fig. 2)

}Ensure that the cables are connected correctly and securely.

Set the main switches to “ I” (ON) in the following sequence.

1. Set the main switch @ of the BX3-CBH control box to “ I” (ON).

2. Set the main switch 2of the control box for BX3-SSU to “ I” (ON).

2Moving the Stage (Fig. 3)

1. Rotate the Y-axis knob 2and X-axis knob @to move the stage.

Factory setting: 10 mm displacement per turn for the coarse adjustment,

0.2 mm displacement per turn for the fine adjustment.

2. Press the coarse/fine selector button 3to switch the knob functions

between the coarse and fine adjustment.

· Pushed in: Coarse adjustment.

· Out position: Fine adjustment.

}The tone occurred when operating the stage may vary drastically in some

cases, but it does not cause any problem for the product performance.

}The stage may be vibrated slightly in some cases when starting the stage,

but the product is not damaged.

CAUTION

3Replacing the Fuses (Fig. 4)

1. Set the main switch of the control box for BX3-SSU to “ ” (OFF) and

unplug the power cord connector from the power outlet.

2. Draw out the fuse box @ by inserting a flat object such as a tip of

screwdriver into the slit 2on the top surface of the fuse box.

3. Replace both of the fuses in the fuse box with new ones.

<< Applicable fuses >>

T3.15A(H)250V (LITTELFUSE 2153.15)

Using a non-specified fuse may cause a fire hazard.

4. Place the fuse box in the original position.

When you use BX3-SSU for the first time, be sure to perform the Auto Compensation of the stage. For detail procedures,

refer to “Auto Compensation of the Stage” described in the previous page.

Fig. 5

4OPTIONAL ACCESSORIES

1Stage Center Plate IX-CP50/IX2-GCP (Fig. 5)

}When using a dish or petri dish sample instead of a slide glass specimen,

remove the slide holder and replace it with the stage center plate.

Be careful not to drop or apply a strong impact to the stage

center plate. Otherwise, it may be deformed or destroyed (in the

case of the glass center plate).

CAUTION

2Stage Clips IX-SCL (Fig. 5)

}The stage clips are used to fix a dish or petri dish sample.

1. Screw the stage clips 2into the two stage clip holes @ on the front side

of the scanning stage with ultrasonic.

Do not use the holes on the rear side to avoid interference with

the objectives.

Andere Handbücher für BX3-SSU

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus BHT Bedienungsanleitung

Olympus

Olympus CX22LED Bedienungsanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus X-Tr Betriebsanleitung

Olympus

Olympus BXFMA Bedienungsanleitung

Olympus

Olympus DP74 Bedienungsanleitung

Olympus

Olympus BXFM Bedienungsanleitung

Olympus

Olympus V60 Bedienungsanleitung

Olympus

Olympus U-CBE Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus MVX10 Bedienungsanleitung

Olympus

Olympus IX2-DSU Bedienungsanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus CHS Bedienungsanleitung

Olympus

Olympus BX53 Bedienungsanleitung

Olympus

Olympus BX53M-P Bedienungsanleitung

Olympus

Olympus CX31-P Bedienungsanleitung

Olympus

Olympus BX51M Bedienungsanleitung

Olympus

Olympus CX43 Bedienungsanleitung

Olympus

Olympus CHA-P Bedienungsanleitung

Olympus

Olympus SZX-AR1 Bedienungsanleitung

Olympus

Olympus SZ-III Bedienungsanleitung

Olympus

Olympus SZX10 Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Handbuch

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung