Olympus BXFMA Bedienungsanleitung

INSTRUCTIONS

BXFMA

MOTORIZED ILLUMINATION SYSTEM

WITH MOTORIZED FOCUSING UNIT

This instruction manual is for the Olympus Motorized Illumination System with Motorized Focusing

Unit, Model BXFMA. To ensure the safety, obtain optimum performance and to familiarize yourself

fully with the use of this system, we recommend that you study this manual thoroughly before

operating the system. Retain this instruction manual in an easily accessible place near the work

desk for future reference.

A X 7 6 1 5

BXFMA-F

U-FH

U-IFFH

U-BI30-2, U-TR30-2, etc.

U-LH100-3

Modules described in this manual

BXFMA

CONTENTS

5-7

8-9

10-16

IMPORTANT — Be sure to read this section for safe use of the equipment. —

1 SYSTEM DIAGRAM

2 NOMENCLATURE

4 USING THE CONTROLS

REFLECTED LIGHT BRIGHTFIELD/DARKFIELD OBSERVATION PROCEDURE

4-1 Power Supply Unit TH4 .............................................................................................................................................................. 10

4-2 Motorized Illuminator with Motorized Focusing Unit BXFMA-F .............................. 10-13

4-3 Observation Tube ...................................................................................................................................................................... 14-15

4-4 Differences in Operating Procedures of Software BX2-BSW.............................................. 16

1-3

1-2 Setting Procedure BX2-BSW Help

Correct assembly and adjustments are critical for the microscope to exhibit its full performance. If you are going to

assemble the microscope yourself, please read Chapter 8, “ASSEMBLY” (pages 23 to 28) carefully.

Selecting the Observation Light Path 2Centering the Field Iris Diaphragm (FS)

Centering the Aperture Iris Diaphragm (AS)

4Adjusting the Motorized Focusing Unit

5Using the Filters

1Adjusting the Interpupillary Distance 2Adjusting the Diopter

3Using the Eye Shades 4Using Eyepiece Micrometer Disks

5Selecting the Light Path of Trinocular Observation Tube

6Adjusting the Tilt

5 TROUBLESHOOTING GUIDE

6 SPECIFICATIONS

7 OPTICAL CHARACTERISTICS <<UIS2 Series>>

17- 18

20-22

23-28

ASSEMBLY

—

See this section for the replacement of the light bulb. —

9 LAMP HOUSING INSPECTION SHEET 29

BXFMA

Fig. 1

Fig. 2

IMPORTANT

The BXFMA-F motorized illuminator with motorized focusing unit can be installed in a user’s system in

combination with the BX-UCB control box as well as a PC (running the BX2-BSW software) or the

U-HSTR2, U-FH focus adjustment knob unit and U-IFFH focus adjustment knob interface.

The instructions for the BX/UCB/U-HSTR2 and software (BX2-BSW, commands) are provided in separate

instruction manuals. Please also refer to these manuals as required.

Motorized Controls · BF (brightfield)/DF (darkfield) switching operation

· AS (aperture iris diaphragm) opening/closing operation

· Focus adjustment operation

Configuration of Instruction Manuals

Manual Name Main Contents

BX-UCB/U-HSTR2 Functions of the Control Box (incorporating the power supply)

and Hand Switch

BX2 Software for PC (CD-ROM)

BX2-BSW Ver. 03.01 or higher

Methods of PC control of functions

# Normal operation is not available unless the specified software is used.

TH4 External halogen lamp power supply

U-FWT/FWR/FWO Motorized filter wheels (Only the U-FWR can be used in this system.)

Precautions When Unpacking the Microscope

}To prevent deterioration in performance during transport, the illuminator is shipped with transport lock applied to the

focusing unit, observation method switch and aperture iris diaphragm (AS) mechanism, Be sure to release the transport

lock of these three modules before assembly, and engage the transport lock before the next transport of the illuminator.

Releasing the Transport Lock of the Observation Method (BF/DF)

Switch Mechanism (Fig. 1)

Turn the lock knob 1counterclockwise to loosen it, and remove it together

with the caution tag.

}Retain the lock knob carefully because it will be used again the next time

the equipment is transported.

To set transport lock:

Releasing the Transport Lock of the Focusing Unit Mechanism (Fig. 2)

1. Turn the two lock knobs 2counterclockwise to loosen and remove them.

2. Similarly to step 1, turn the two lock screws 3to remove them.

}Retain the lock knobs and lock screws carefully because they will be

used again the next time the equipment is transported.

To set transport lock:

This motorized illuminator can manifest its functions when it is combined with other modules. The instructions

manuals for the following modules are prepared separately to the present instruction manual. Please read the

manuals according to your own system.

1. Switch the observation method to DF (reflected light darkfield).

2. Turn the lock knob all the way clockwise.

1. Raise the focusing unit to the higher limit position.

2. Turn the two lock screws all the way clockwise.

3. Similarly to step 2, turn and tighten the too lock knobs.

Fig. 3

SAFETY PRECAUTIONS

1. Keep your hands apart from the revolving nosepiece during focusing

operation and while the main switch of the BX-UCB control box is set to

“ I” (ON). If your finger is caught by the up/down movement of the revolving

nosepiece, an injury such as bone fracture my result.

Should your finger be caught by the revolving nosepiece, lower it with the

following method:

· Set the main switch to “ ” (OFF), remove the right side panel of the

illuminator using a Phillips screwdriver and turn the manual knob 1 inside

the panel in the opposite direction to the direction shown in the figure (i.e.

clockwise) to lower the revolving nosepiece. (Fig. 3)

2. Emergency stop of focus operation is possible by turning the focus

adjustment knob on the microscope frame or on the U-FH (in either

direction), or by pressing the FOCUS control button ( , , F/C or ESC),

after focus operation has been activated (except when data is being

downloaded to a PC).

When the BX-UCB control box’s main switch is set to “ I” (ON), the focus

operates automatically (the objective raises once and then returns to the

original position) for initialization. (It takes about 20 seconds.)

If the above emergency procedure is performed during this automatic

focus operation, the microscope stops operating. Should this happen,

set the main switch to “ ” (OFF) and then “ I” (ON) again.

3. The surface of the lamp housing on the side of the illuminator becomes

very hot. When installing the system, leave spaces of more than 10 cm

around, particularly above the lamp housing.

4. Be careful not to touch the lamp housing when centering the aperture

iris diaphragm or controlling the field iris diaphragm. You run the risk of

burn if you touch the lamp housing while the lamp is lit or immediately

after it is turned off.

5. Route the connection cables away from the lamp housing. Should a

cable comes in contact with the hot lamp housing, the cable could melt

and cause electric shock.

6. When installing the illuminator in an existing system, insert 6 bolts in the

module installation screw holes and tighten firmly.

Safety Symbols

Symbol Explanation

Indicates that the surface becomes hot, and should not be touched with bare hands.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Before use, carefully read the instruction manual. Improper use could result in personal injury to

the user and/or damage to the equipment.

The following symbols are found on the motorized illumination system. Study the meaning of the symbols and always

use the equipment in the safest possible manner.

Be careful not to have your finger or hand caught (between the revolving nosepiece and illuminator

or between the specimen and objective).

BXFMA

Warnings

Warning engravings/sticklers are placed at parts where special precaution is required when handling and using the

system. Always heed the warnings.

Warning engraving

positions

Lamp housing

(U-LH100L-3, U-LH100-3)

(High Temperature

warning )

Warning sticker

positions

Motorized illuminator

BXFMA-F

(Finger injury

warning)

Active AF unit

U-AFA1M (Laser warning)

1Getting Ready

1. The illuminator is a precision instrument incorporating motorized parts. Always install it horizontally (it is inhibited to install

it on the side panel), handle it with care and avoid subjecting it to sudden or severe impact.

2. Do not use the system where it is subjected to direct sunlight, high temperature and humidity, dust or vibrations. (For

operating conditions, see Chapter 6, “SPECIFICATIONS” on page 19).

3. Only one intermediate attachment can be used, by installing the U-AFA1M active AF unit, U-CA magnification changer or

U-EPA2 eye point adjuster above the motorized illuminator.

2Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirty away using a commercially available blower and wipe

gently using a piece of cleaning paper (or clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

!Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks –– for example, electrical

equipment that is being switched on or off.

Also remember to always use it only in a well-ventilated room.

2. Do not attempt to use organic solvents to clean the non-optical components of the microscope system. To clean them,

use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Never attempt to disassemble any part of the microscope system.

4. When not using the microscope, set the main switch to “ ” (OFF), wait until the lamp housing has cooled down, and

cover the microscope with a dust cover before storage.

5. When disposing of this product, check the regulations and rules of your local government and be sure to observe them.

3Caution

If the system is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

!: Indicates that failure to follow the instructions in the warning could result in bodily harm to the

user and/or damage to equipment (including objects in the vicinity of the equipment).

# : Indicates that failure to follow the instructions could result in damage to equipment.

} : Indicates commentary (for ease of operation and maintenance).

SYSTEM DIAGRAM

}The modules marked *are not required when a PC is used to control all operations from the PC.

The PC used in this system should meet the requirements by IEC60950. Be sure to use an Olympus-designated

connection cord. If a non-designated connection cord is used, Olympus cannot guarantee any performance of the

system.

Focus Adjustment

Knob Unit

U-FH*

Focus Adjustment

Knob Interface

U-IFFH*

Connection cable*

(50-pin)

(Rear panel)

RS232C cable

(BX2-BSW

installed)

Control Box

BX-UCB

Z-Board

U-ZPCB(T2)

AF Board

U-AFA1-CB

Power Supply

Unit

TH4*

Hand Switch

U-HSTR2*

TV system

Observation tube

· U-BI30-2

· U-TR30-2

· U-TBI3

· U-TUL, etc.

Active AF Unit

U-AFA1M

Motorized Revolving

Nosepiece

· U-D5BDREMC

· U-D6REMC

· U-P5REMC

· U-D5BDREM

· U-D6REM

Objective

Connection

cable

(50-pin) Connection

cable

(36-pin)

Extension Cord

U-RMT

High-Intensity

Lamp Housing

· U-LH100HG

· U-LH100HGAPO

· U-LH50MH

· U-LH75XEAPO

100 W Halogen

Lamp Housing

· U-LH100-3

· U-LH100L-3

Auxiliary ring

(provided with the

BXFMA-F)

Filter Wheel

U-FWR (Note)

Special power

supply

Motorized Illuminator

with Motorized

Focusing Unit

BXFMA-F

Surface for installation

on system:

· Bottom panel

· Left side panel

Connect to FW1, 2 or 3

of BX-UCB

()

(Note) The cable of the U-FWR filter wheel runs close to the lamp housing when the filter wheel is attached.

Position the cable so that it does not come in contact with the lamp housing.

BXFMA

NOMENCLATURE

Motorized Illuminator with Motorized Focusing Unit

BXFMA-F

}The observation method (BF/DF) switching, aperture iris diaphragm opening/closing and focus adjustment (which can also

be controlled using the U-FH focus adjustment knob unit) can be controlled using the BX2-BSW software run on the PC.

Surface for installation on system

(Left side panel)

Filter slider (Page 13)

AF support bracket clamping screws

(x 4)

Aperture iris diaphragm lock screw (Page 11)

Auxiliary ring (Note 1)

Aperture iris diaphragm

centering screws (Page 11)

Field iris diaphragm centering screws (Page 10)

Field iris diaphragm lever (Page 11)

Surface for installation on system

(Bottom panel)

Allen wrench (1.5 mm)

Allen screwdriver (3 mm)

Seals (x 6)

AF support brackets

(Page 28)

Field iris diaphragm auxiliary lever

(Detachable)

Connection cable

(50-pin)

(36-pin)

(Note 1) The auxiliary ring is for use with the high-

intensity lamp housing. When the halogen

lamp housing is used, remove the ring by

loosening the 2 clamping screws using the

Allen screwdriver.

Hand Switch U-HSTR2

}The button functions shown below refer to those in the standalone operation.

The button functions can be set arbitrarily when PC control (remote control) is used.

For other operating instructions, refer to the BX-UCB/U-HSTR2 instruction manual.

DF (Darkfield) button

Focus Adjustment Knob Interface U-IFFH

U-FH connector

Power Supply Unit TH4

}For details, refer to the separate

instruction manual.

Main switch

BF (Brightfield) button

AS+ (Aperture iris diaphragm open)

button

AS– (Aperture iris diaphragm close)

button

Projections for blind-touch operation

Connector

Objective buttons

UCB1 (illuminator) connector

BX-UCB connector

I : ON. : OFF. Light intensity control

POWER LED

REMOTE LED

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus IX73 Bedienungsanleitung

Olympus

Olympus CX31 Bedienungsanleitung

Olympus

Olympus AL120-12 Series Bedienungsanleitung

Olympus

Olympus Discover FV10i Betriebsanleitung

Olympus

Olympus BX41 Bedienungsanleitung

Olympus

Olympus FHT-521 Bedienungsanleitung

Olympus

Olympus BX60 Bedienungsanleitung

Olympus

Olympus IX71 Bedienungsanleitung

Olympus

Olympus DP21 Bedienungsanleitung

Olympus

Olympus CH10 Betriebsanleitung

Olympus

Olympus bx40 Bedienungsanleitung

Olympus

Olympus Lext OLS3100 Bedienungsanleitung

Olympus

Olympus BX53M-P Bedienungsanleitung

Olympus

Olympus SZX7 Bedienungsanleitung

Olympus

Olympus DP22 Bedienungsanleitung

Olympus

Olympus BH2 Series Montageanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus BX45 Bedienungsanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus BX60 Bedienungsanleitung

Olympus

Olympus BHA-P Bedienungsanleitung

Olympus

Olympus DSX510 Bedienungsanleitung

Olympus

Olympus CKX31 Betriebsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung