Olympus FV3000 Bedienungsanleitung

Provisionary

https://uol.de/neurosensorik/forschung/fluorescence-microscopy-service-unit

Olympus FV 3000 operation manual

1. Switch on PC (password olympus)

2. Switch on the main power switch on the cord extender in the Rack. Stage control

and microscope controller will switch on automatically.

3. Switch on laser lines which you plan to use. System has 405nm, 445nm, 488nm,

514nm, 561nm, 594 nm and 640 nm cw diode lasers.

4. Turn on the key to activate the lasers. The lasers will blink with green. Then they

show white lamp on, they are ready to use.

5. You can add a laser line later when software is running too.

6. Turn on touch PC (the switch is on the back) and wait until it is initialized. Blue and

green light should light up on the controller.

7. If you need heating and CO2, switch on the cord extender for the Cell Vivo (heating

and CO2 control unit) and start Cell Vivo software. And start heating 1hour in

advance minimum

8. Start the FV31S-SW software

9. Now you can switch on FLIM system (use a FLIM guideline)

10. Keep resonant scanner unchecked if you do not need it. If you need it, for stability

start it 30 minutes before your scans.

11. Keep other settings in the start dialog unchanged (enable XY on)

12. Choose NO for stage cleaning

13. Choose objective either in software or on touch PC. The microscope has 1.25x NA

0.04, 4x NA 0.16, 20x NA 0.8, 40x NA 1.4 oil, 30x NA 1.05 Silicon oil and 60x NA 1.3

Silicon oil. If using oil objective, CHECK THAT YOU USE RIGHT TYPE OF OIL

14. Check the collar correction on the objective. It should be set to 0.17mm if you use

1.5# cover slips. Note that at 23C and at 37C the correction is different.

15. Use the Camera/Eye button on the touch panel controller to switch between Laser

Scanning Mode (LSM, camera symbol) to Ocular view (eye symbol). You will probably

need to adjust light intensity.

16. Find your sample using epifluorescence (EPI) or transmission light (DIA). For EPI

select Quad filter, on position. 2.

17. For EPI choose 1V for violet excitation (DAPI), 2B for blue excitation (GFP) and 3GR

for red excitation (RFP) for LEDs.

18. Open and close shutter when needed

19. Check that COOL LED is on.

Provisionary

https://uol.de/neurosensorik/forschung/fluorescence-microscopy-service-unit

20. In software choose in Ocular pannel, and LSM

21. In the “LSM imaging “panel adjust adjust Scan

Setting: Scanner Type: Galvo, Oneway mode. Scan

speed: 2µs/pix.

22. In the “PMT” panel adjust Scan Setting: use VBF.

23. In the “PMT” panel set channels for your dyes, by pressing the “Dye & Detector

select” button. Adjust emission bandwidth if needed.

24. In the “PMT” panel check the confocal aperture. Use AUTO to have it averaged for all

channels.

25. Start with low laser power 0.5%, HV 500, offset 0% (max 3%), do not change gain.

You can set up two 4 channels in one group plus transmission light channel.

Detection regions should not overlap with laser lines.

26. In the “Area Settings” panel select the Scan Size and use the Optimize button to

adjust the Zoom for Nyquist-sampling

27. Check for over and underexposure (Hi-Lo).

28. Check bleadthrough, i.e if you see signal from one laser in another channel. If

bleadthrough, go to “PMT” panel, select “sequential sc” and the mode “Line” or

“Frame” (Frame is faster).

29. Be careful and do not overexpose PMTs. (indicated by red colour in Hi-Lo mode)

30. Set a folder where your images will be saved. Use the D-drive for it and find your AG-

folder. The image format will be *.oir

31. Set averaging/accumulation if you need it.

32. Check if Z series and t-series are off

33. Do your imaging: press LSM-START

Finish your work

1. When finished: close the software.

2. if used heating and CO2 then stop heating and CO2 in the Cell Vivo software and

close it. Switch off Cell Vivo switch on the power cord. Close CO2 valves.

3. Copy your data to the data transfer server.

4. Switch off FLIM system if it was on

5. On the touch PC screen press OFF, when OLYMPUS is displayed, switch off the touch

PC using the switch on the back.

6. Turn the key to deactivate lasers.

7. Switch off all lasers which are on.

8. Switch off the main switch on the power cord in the rack.

9. Remove your sample

10. Clean oil objective with isopropanol and lens paper.

11. Write you name, date and comments in the electronic log book.

12. Switch off the PC.

For Z-stack:

1. In acquisition choose Z-series on (Z Section panel, bottom right)

2. Find bottom position, register it, then find a top position and register it.

3. Go from the lower position to higher position.

4. Optimize step size accordingly to your needs (Or press the “Optimize” button).

Provisionary

https://uol.de/neurosensorik/forschung/fluorescence-microscopy-service-unit

ZDC: drift compensation (does not work with 1.25x and 4x)

1. Check the current position and check NEAR-limit settings: approx. numbers 1800 for

cover slips, petri dish 2300, well plate about 3500. (Please verify the values for petri

dish and well plate with your vessels again)

2. Press “Apply entered parameters to near limit”.

3. Place ZDC dichroic mirror in: ZDC DM IN

4. On Touch PC press START for focus search in EPI mode. If it is successful, you hear

one beep.

5. Use Single shot mode for multipoint imaging experiments (Z stacks etc) and

Continuous mode for long-term time-lapse experiments.

6. At ZDC you cannot change objectives.

7. ZDC does not work well with oil objective, but good with Silicon oil objective.

Objectives:

30x Silicon and 60x Silicon are good for live cell imaging: SILICON OIL

40x oil is good for fixed samples: NORMAL OIL

Shortcuts:

1. F11 start/stop live

2. F12 start image scan

3. Ctrl and mouse scroll: focusing

4. Double click on the image while life moves the stage

Provisionary

https://uol.de/neurosensorik/forschung/fluorescence-microscopy-service-unit

OIL:

To use Cell Vivo heating and CO2 controller:

1. If you did not start it before press the button on the power extender under the Cell

Vivo controller.

2. Start Cell Vivo software.

3. To heat the incubator set the temperature H unit 2000 to T you need and press ON.

4. You can log Temperature data.

5. To have stable temperature 1-2 hours heat up time is required.

6. When finished, stop heating

7. Close the software

8. Switch off the controller using the button on the power extender.

Stage control

40x oil

30x and 60x

Silicon oil

Provisionary

https://uol.de/neurosensorik/forschung/fluorescence-microscopy-service-unit

Andere Handbücher für FV3000

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus SZ4045TR Bedienungsanleitung

Olympus

Olympus SZ3060 Bedienungsanleitung

Olympus

Olympus IMT-2 Bedienungsanleitung

Olympus

Olympus U-MDOB3 Bedienungsanleitung

Olympus

Olympus BX51M Bedienungsanleitung

Olympus

Olympus SZX9 Bedienungsanleitung

Olympus

Olympus CKX53 Bedienungsanleitung

Olympus

Olympus CHA-P Bedienungsanleitung

Olympus

Olympus VS110 Fluorescence Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus DP21-SAL Benutzerhandbuch

Olympus

Olympus BXFMA Bedienungsanleitung

Olympus

Olympus VS120 Bedienungsanleitung

Olympus

Olympus BX45 Bedienungsanleitung

Olympus

Olympus CHBS Bedienungsanleitung

Olympus

Olympus BH2 Series Montageanleitung

Olympus

Olympus SZ-III Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus KHC Bedienungsanleitung

Olympus

Olympus IX71 Bedienungsanleitung

Olympus

Olympus ORBEYE Handbuch

Olympus

Olympus DP71 Bedienungsanleitung

Olympus

Olympus CX43 Bedienungsanleitung

Olympus

Olympus BHTU Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung