Omron WT30 Bedienungsanleitung

FA Wireless SS Terminals WT30 1

FA Wireless SS Terminals

WT30

Construct a Wireless System for ON/OFF

Data Collection That Is Ideal for Monitoring

Production Site Equipment

• Wireless Slave Station equipped with I/O.

• Height of 90 mm and DIN Rail mounting enables installation in

control panels.

• Easily check wireless communications status from indicator

display.

• I/O Slave Stations can also be used as Slave Stations in WD30

systems.

• Conforms to radio wave standards for Japan, China (pending),

USA, and Europe.

Ordering Information

■List of Models

Note: An Antenna and Mounting Brackets are not included with the Wireless SS Terminal.

■Accessories

Antennas

Communications Cables

Other

Applicable Standards

•FCC part 15.247 (USA)

•EN 300 440-2 (Europe)

•ARIB STD-T66 (Japan)

•(China) (approval pending)

Main Class 2 Power Supplies

OMRON Switching Power Supplies

•S8VS (15 W, 30 W, 60 W type)

•S82K (15 W, 30 W, 50 W, 90 W type)

Applicable Countries

Wireless standards have been met for the following countries. The

product cannot be used in any other countries.

Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungry, Iceland, Ireland, Italy,

Japan, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland,

UK, USA

Wireless Unit model Type Specifications/No. of I/O points

WT30-M01-FLK Serial master RS-232C

WT30-SID16 I/O slaves 16 DC inputs (NPN/PNP)

WT30-SMD16 8 DC inputs (NPN/PNP) + 8 transistor outputs (NPN)

WT30-SMD16-1 8 DC inputs (NPN/PNP) + 8 transistor outputs (PNP)

Model Type

WT30-AT001 Magnet-base Antenna (2 antennas per set)

WT30-AT002 Flat Diversity Antenna (1 antenna)

WT30-AT003 Pencil Antenna (2 antennas per set)

Model Length Application

XW2Z-0100U-3 1 m For personal computer

XW2Z-0200U-3 2 m

XW2Z-0500U-3 5 m

XW2Z-0200U-5 2 m Cross cable for PLC

XW2Z-0500U-5 5 m

Model Type

WT30-FT001 DIN Rail Mounting Bracket (for TH35-7.5)

WT30-FT002 DIN Rail Mounting Bracket (for TH35-15)

WT30-FT003 Surface Mounting Bracket (screw-mounting)

(2 brackets per set)

WT30-FT011 Flat Diversity Antenna Mounting Brackets

(with magnets)

WT30-CA2M Antenna Extension Cable (1 cable, 2 m)

Conformity to Safety Standards

Always use a Class 2 power supply to conform to UL standards.

Conformity to EN Standards

Use a DC power line less than 3 m to conform to EN standards. If a

power line of 3 m or longer is required, extend the length at the

Switching Power Supply’s primary side (i.e., the AC power line).

2FA Wireless SS Terminals WT30

Specifications

■Ratings

Note: 1. Provide a power supply of at least 15 W, considering the inrush current generated at startup.

2. Use the WT30-FT003 Surface Mounting Bracket when installing the WT30 in environments subject to vibration.

■Wireless Interface Specifications

Note: Varies according to the installation environment.

■Package Contents

•WT30 FA Wireless SS Terminal •Terminal labels (I/O Slaves only)

•Instruction Sheet •Adhesive non-slip feet (Serial Master only)

Item WT30-M01-FLK Serial Master WT30-SID16/SMD16/SMD16-1 I/O Slaves

Power supply

(wireless

communications

power supply)

Rated voltage 24 V DC

Allowable voltage

range

20.4 to 26.4 V DC

Power consumption 3 W max. (See note 1.)

Error output/output

power supply

(for output circuits)

Rated voltage --- 24 V DC

Allowable voltage

range

--- 20.4 to 26.4 V DC

Insulation resistance 20 MΩmin. (at 100 V DC) between the power

supply and chassis

20 MΩmin. (at 100 V DC) between the power

supply and all I/O and I/O power supply and

between the power supply and chassis

Dielectric strength 1,500 V AC for 1 min between power supply

and chassis

1,500 V AC for 1 min between the power supply

and all I/O and I/O power supply and between

the power supply and chassis

Noise immunity IEC61000-4-4. 1 kV (power supply line)

Vibration resistance (See note 2.) JIS C0040

Frequency: 10 to 55 Hz; Amplitude of 0.35 mm or acceleration of 50 m/s2, whichever is smaller

(DIN Rail mounting: single amplitude of 0.1 mm or acceleration of 15 m/s2)

10 sweeps of 8 min each (i.e., 80 min in total) in X, Y, Z directions

Shock resistance Conforms to JIS C0041: 300 m/s23 times each in X, Y, and Z directions

Ambient operating temperature −10 to 55°C (with no condensation or icing)

(with the Terminal mounted with the dust-proof

label facing up)

Number of simultaneously ON I/O points

10 max.: −10 to 55°C (with no condensation or

icing)

16 max.: −10 to 50°C (with no condensation or

icing)

(with the Terminal mounted with the dust-proof

label facing up)

Ambient operating humidity 25% to 85% (with no condensation or icing)

Ambient environment No corrosive gases

Storage temperature −25 to 65°C (with no condensation or icing)

Protective structure IP20

Terminal construction Power supply and I/O Screwless terminal block (Phoenix Contact FFKDS/V1-5.08 or equivalent)

Serial D-sub, 9-pin (female) Inch screws (OMRON

XM2F-0910-132 or equivalent), Master station

only

---

Safety standards UL: UL508 (Listing)

Weight 330 g max.

Item Specifications

Wave type Spread Spectrum (direct sequence; DS-SS)

Communication method Simplex

Frequency band 2,401 to 2,480.2 MHz

Number of channels 67 channels (based on switching)

Transmitter output power 10 mW/MHz

Baud rate between wireless stations 100 kbps

Communications distance (See note.) Indoors: 60 m min. (approx. 50 m min. with Magnet-base Antennas and Flat Diversity Antennas)

Outdoors: Approx. 300 m min. (anticipated distances)

(without using relay stations)

Error detection method CRC-CCITT (16 bits)

Relay functions One stage using I/O slave for the serial master configuration.

Number of stations per area (See note.) 10 sets max. (recommended)

Number of I/O Slaves connected 64 max.

FA Wireless SS Terminals WT30 3

Nomenclature

■Serial Master Station

■I/O Slave Station

■Unit No. Switch

Set the unit number of the Serial Master Station

Default: 00

■Node Setting Switch (WNODE)

Set the number of connected I/O Slave Stations.

Set the node number of the Slave Stations being used as I/O Slave

Stations. The Slave Station functions as a relay station when the

node number is set to 99.

Default: 01

■Channel Setting Switch (WCH)

Set the communications frequency.

Default: 02

■Function Setting Switch

Serial Master Station

I/O Slave Station

Antenna terminal (ANT1)

Status

indicators

RS-232C Terminal

Connect the PLC, personal computer, etc.

Power supply terminal

Supply power to the WT30.

Unit No. switch

Set the unit number of the Serial Master Station.

Node setting switch (WNODE)

Set the number of connected I/O Slave Stations.

Channel setting switch (WCH)

Set the communications frequency

channel.

Antenna terminal (ANT2)

Received

signal

strength

indicator

Special

function

switch

Function setting switch

Make the detailed settings

for RUN/TEST/SET mode.

Mode selection switch

Switch between RUN,

TEST, and SET mode.

Serial communications

setting switch

Set the baud rate.

Status

indicators

Power supply terminal

Supply power to the WT30

and output circuits.

Mode selection switch

Switch between RUN,

TEST, and SET mode.

Node setting switch (WNODE)

Set the unit number of the I/O Slave Station.

I/O terminal status indicators (0 to 7 or 8 to 15)

The contact status is displayed.

Channel setting switch (WCH)

Set the communications frequency.

Antenna terminal (ANT2)

Received

signal

strength

indicator

Special function switch

Antenna terminal (ANT1)

Function setting switch

Make the detailed settings

for RUN/TEST mode.

I/O terminals

Connect the contact

signals.

No. Applicable

mode

ON functions OFF functions

1RUN mode Holds I/O status data

when a

communications error

occurs.

Clears I/O status data

when a

communications error

occurs.

2Enable scan list Disable scan list

3Relays used Relays not used

4TEST mode Signal strength monitor

disabled

Signal strength monitor

enabled

5All channels

automatically switched

Specified channels

6--- ---

7SET mode Scan list recognition Nothing done

8Registers specified I/O

slave

Registers all I/O slaves

automatically

9Recognizes serial

numbers

Ignores serial numbers

10 Not used --- ---

No. Applicable

mode

ON functions OFF functions

1RUN mode Holds I/O status data

when a

communications error

occurs.

Clears I/O status data

when a

communications error

occurs.

2Input hold Normal mode

3Input filter: 100 ms Input filter: 10 ms

4TEST mode Signal strength monitor

disabled

Signal strength monitor

enabled

5All channels

automatically switched

Specified channels

6Installation test

function

Nothing done

7 to

Not used --- ---

4FA Wireless SS Terminals WT30

■Serial Communications Setting

Switch

Note: For example, if pins number 2, 3, and 4 are all ON, the total is

7, which corresponds to a baud rate of 115,200 bps.

■Display

Note: When using the WD30 as the Serial Master Station, the ERR

indicator will light if normal I/O communications are not

possible due to an error in the host network.

No. Function ON OFF

1Communications setting

selection

Detailed

settings

(settings for

No. 2 to 8

used)

Default settings

(baud rate: 9,600 bps;

data length: 7 bits;

parity: even; stop bits:

Settings for No. 2 to 8

are ignored.

2Baud rate (bps)

(See note.)

Total value = 0: 1,200

= 1: 2,400

= 2: 4,800

= 3: 9,600

= 4: 19,200

= 5: 38,400

= 6: 57,600

= 7: 115,200

320

440

5Data length 8 bits 7 bits

6Parity None Yes

7Odd Even

8Stop bits 1 bit 2 bits

Indicator Color Status Meaning (primary error)

PWR Green Lit Power is being supplied.

Not lit Power is not being supplied.

ERR

(Slave Station)

Red Lit Error output is ON:

Wireless device error or

wireless communications

error. (See note)

Not lit No wireless device error or

wireless communications

error.

COMM

(Master Station)

Yellow Lit Serial communications in

progress.

Not lit No serial communications.

0 to 15

(Slave Station)

Yellow Lit/Not lit ON/OFF status for input or

output signals

RSSI Red/

Yellow/

Green

Lit/

All not lit

Receiving Signal Strength

Indicator monitor: Number of

indicators lit (receiving signal

strength 1 to 9)

Receiving signal strength less

than 0 to 1.

(Module Status)

Green Lit Communications are normal.

Flashing TEST mode or SET mode has

been activated.

Red Lit A fatal error has occurred that

cannot be recovered from.

Replace the Unit

Flashing A non-fatal error has occurred

that can be recovered from by

resetting the system.

--- Not lit Power is not being supplied or

the system is resetting.

(Wireless

Status)

Green Lit The station has joined the

wireless network.

Flashing Permission to join wireless

network received from Serial

Master Station (Slave Station)

Red Lit A fatal error has occurred that

cannot be recovered from.

Flashing Error from which recovery is

possible

--- Not lit Wireless communications are

not in progress.

FA Wireless SS Terminals WT30 5

Wiring

■Serial Master Station (WT30-M01-FLK)

I/O Characteristics

■I/O Slave Station

RS-232C Connector

WT30 Power supply terminal

Supply power to the Unit

54321

9876

D-sub, 9-pin, Female End at WT30

Pin No. Signal I/O direction

1 --- ---

2RDOutput

3 SD Input

4 --- ---

5 SG ---

6 --- ---

7 --- ---

8 --- ---

9 --- ---

VG 01 2 3

COM

4567

COM ERRP

24 V DC

0 V 8 9 10 11

COM

12 13 14 15

COM ERRN

Power supply Inputs Inputs

Inputs Inputs

Error output

(

NPN

)

Error output

power supply

Error output

(PNP)

Error output

(NPN)

OUT

24 V DC

0 V 0 1 2 3

COM

4567

COM ERRN

Power supply Outputs Outputs

VG0 1 2 3

COM

4567

COM ERRP

Inputs Inputs

Error output/output

power supply

Error output

(PNP)

WT30-SID16

WT30-SMD16

WT30-SMD-16-1

Item Specifications

Input Characteristics

Input voltage 24 V DC

Allowable

voltage range

20.4 to 26.4 V DC

Input

impedance

4.7 kΩ(typical)

Input current 5 mA (typical)

ON voltage/

current

characteristics

17.4 V DC, 3.0 mA min.

OFF voltage/

current

characteristics

5.0 V DC, 1.0 mA max.

Input filter 10 ms/100 ms (Selected using switch.)

Output/Error Output

Characteristics

Input voltage 24 V DC

Allowable

voltage

20.4 to 26.4 V DC

Max.

switching

current

100 mA max. per output (at 20.4 to 26.4 V DC)

Simultaneous usage of error output NPN/PNP

is not possible.

Leakage

current

0.1 mA max.

Residual

voltage

1.0 V max.

Fuse One for every two outputs except for error

output circuits, which have one for every NPN/

PNP output. (No fuses can be replaced by the

user.)

6FA Wireless SS Terminals WT30

Input Circuit Diagram

Error Output Circuit Diagram

Output Circuit Diagram (NPN)

Output Circuit Diagram (PNP)

Dimensions

Note: All units are in millimeters unless otherwise indicated.

Serial Master Station

WT30-M01-FLK

I/O Slave Station

WT30-SID16

WT30-SMD16

WT30-SMD16-1

IN 0

IN 1

IN 2

IN 15

COM (IN)

Secondary internal circuit

ERRN

ERRP

Fuse

Secondary internal circuit

Fuse

OUT 0

OUT 1

OUT 2

OUT 7

Secondary internal circuit

Fuse

OUT 0

OUT 1

OUT 2

OUT 7

Fuse

OUT

Secondary internal circuit

Fuse

Four, 5 dia.

(15)

60 40

13.3 105 13.3

120

Surface mounting bracket

WT30-FT003

105

7.3

DIN rail mounting bracket

WT30-FT001 or WT30-FT002

FA Wireless SS Terminals WT30 7

With Magnet-base

Antenna

WT30-AT001

With Flat Diversity

Antenna

WT30-AT002

With Pencil Antenna

WT30-AT003

Magnet-base Antenna

WT30-AT001

Flat Diversity Antenna

WT30-AT002

Pencil Antenna

WT30-AT003

DIN Rail Mounting

Bracket

WT30-FT001

WT30-FT002

Surface Mounting

Bracket

WT30-FT003

Flat Diversity Antenna Mounting

Brackets (with magnets)

WT30-FT011

(34)

(32)

(38)

4.6

R38

R40

I/O Slave Station

DIN Rail mounting bracket

WT30-FT001 or

WT30-FT002

(23)

R50

I/O Slave Station DIN Rail mounting bracke

WT30-FT001 or

WT30-FT002

150 40

(46)

Surface Mounting Bracket

WT30-FT003

Serial Master Station

115

2010

35.8 dia.

10.5 dia.

57.5

2010

57.5

Three, 3 dia.

10.5 dia

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Cat. No. N139-E1-01

OMRON Corporation

Industrial Automation Company

Industrial Devices and Components Division H.Q.

Wireless Components Department

Shiokoji Horikawa, Shimogyo-ku,

Kyoto, 600-8530 Japan

Tel: (81)75-344-7116/Fax: (81)75-344-7189

Printed in Japan

0105

Andere Handbücher für WT30

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Touch-Terminal Handbücher

Omron

Omron NT30 Bedienungsanleitung

Omron

Omron NB3Q-TW**B series Installations- und Betriebshandbuch

Omron

Omron NT31 Series Installationshandbuch

Omron

Omron NXR-ILM08C-EIT Bedienungsanleitung

Omron

Omron NT2S-SF121B-E - Gebrauchsanweisung

Omron

Omron NS10-TV Series Betriebsanleitung

Omron

Omron Sysmac NA Series Bedienungsanleitung

Omron

Omron NT2S-SF122B-E START V1.03 Gebrauchsanweisung

Omron

Omron NS7 Series Benutzerhandbuch

Omron

Omron NA-series Bedienungs- und Wartungshandbuch

Omron

Omron Programmable Terminals NT31 NT31C Benutzerhandbuch

Omron

Omron NS - REV 12 Benutzerhandbuch

Omron

Omron NT3S Bedienungsanleitung

Omron

Omron Programmable Terminals NT631 Installationshandbuch

Omron

Omron NT20S-ST121B-EV3 Bedienungsanleitung

Omron

Omron NSJ5 Bedienungsanleitung

Omron

Omron NS10-TV Series Benutzerhandbuch

Omron

Omron DeviceNet DRT2-ID16S-1 Bedienungsanleitung

Omron

Omron NXR-ILM08C-ECT Bedienungsanleitung

Omron

Omron DeviceNet DRT2-AD04 Bedienungsanleitung

Omron

Omron NT631 Series Bedienungsanleitung

Omron

Omron NSH5 Bedienungsanleitung

Omron

Omron NSH5 Bedienungsanleitung

Omron

Omron NA-series Gebrauchsanweisung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung