ParaBody 441101 440 Bedienungsanleitung

441101 440 LEG PRESS ADAPTER KIT

Part # 7039101

REV. B Revision: 07/19/011

ASSEMBLY INSTRUCTIONS

WARNING:

Read and follow all directions

for each step to insure proper

assembly of this product.

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please

follow these rules:

IMPORTANT NOTES

1. Consult your physician before beginning any exercise program.

Please note:

Tools Required for Assembly

* Thank you for purchasing the Parabody 441101 Leg PressAdapter Kit. Please read these

instructions thoroughly and keep them for future reference. This product must be assembled

on a flat, level surface to assure its proper function.

* Rubber mallet or hammer

* 3/4” wrench

* 9/16” wrench

* Ratchet with 3/4” and 9/16” sockets

* 5/32” Allen wrench

* Adjustable wrench

* Tape measure

NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.

BOLT LENGTH RULER:

3. Do not allow minors or children to play on or around this equipment.

2. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.

Failure to do so may result in serious injury.

4. Exercise with care to avoid injury.

5. If unsure of proper use of equipment, call your local Parabody distributor or call the

Parabody customer service department at (800) 328-9714.

* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy

water. Touch-up paint can be purchased from your Parabody customer service representative

at (800) 328-9714.

Bolt Length Ruler

0123456

1/2 1/2 1/2 1/2 1/2 1/2

BOLT LENGTH

FIGURE 1

STEP 1

• Slide two COVER CAPS (7) over the FRONT LEG (1)

as shown in FIGURE 1

PARTS LIST

PART #

6686608

6693902

6694002

6694208

3116201

6405201

6467001

3108102

6140701

KEY

QTY

PART #

3102501

3102802

3102801

3102924

3102904

3102918

7032303

6694401

DESCRIPTION

3/8” WASHER

3/8” LOCKNUT

1/2” LOCKNUT

3/8 X 1-3/4” BOLT

3/8 X 3” BOLT

1/2 X 3-1/4” BOLT

110-3/4” CABLE ASSY

82-1/2” CABLEASSY

QTY

DESCRIPTION

FRONT LEG

PULLEYBRACKET

CABLESWIVEL

BASECONNECTION

3-1/2” PULLEY

2” SQ. END CAP

COVER CAP

QUICK DISCONNECT LINK

GLIDE 1 X 1”

KEY

FIGURE 2

STEP 2

• Slide one 2” SQ. END CAP (6) into the BASE CONNECTION (4)

as shown in FIGURE 2.

FIGURE 3

STEP 3

• Attach two 1 X 1” GLIDES (9) to the top of PULLEY BRACKET

(2) as shown in FIGURE 3.

NOTE: The LEG PRESS ATTACHTMENT (100101) must be assembled before connecting it to the

PARABODY 440 HOME GYM

FIGURE 4

FIGURE 5

1/2X3-1/4” 15

STEP 4

• Securely fasten the FRONT LEG (1) and the BASE CONNECTION (4) to the 440 HOME GYM using two 1/2 X 3-1/4” BOLTS

(15) and two 1/2” LOCKNUTS (12). See FIGURE 4.

STEP 5

• Remove one existing 3-1/2” PULLEYand two SPACERS

from theADJUSTMENTTUBE on the 100 LEG PRESS

OPTION by unfastening the 3/8 X 4-1/2” BOLTholding

the pulley on. See FIGURE 5. (Note: Save 3-1/2”

PULLEY, it will be used in later steps.)

0123456

1/2 1/2 1/2 1/2 1/2 1/2

3-1/2” PULLEY

2” WHEEL

3/8 X 4-1/2”

BOLT

SPACER

FIGURE 7

FIGURE 6

STEP 6

• Attach CABLE SWIVEL (3) to the

ADJUSTMENT TUBE on the 100 LEG

PRESS using the existing previously removed

3/8 X 4-1/2” BOLTS, WASHERS, 2”

WHEELS AND NUT. (Note: Securely

tighten, then back off 1/4 turn to allow the

CABLE SWIVEL & WHEELS to rotate

freely.) See FIGURE 6.

2” WHEEL

3/8 X 4-1/2” BOLT

NUT

2” WHEEL

STEP 7

• Securely fasten the 100 LEG PRESS to the FRONT LEG (1) using two 3/8 X 3” BOLTS (14), four 3/8” WASHERS (10), and two

3/8” LOCKNUTS (11) as shown in FIGURE 7.

3/8 X 3” 14

0123456

1/2 1/2 1/2 1/2 1/2 1/2

STEP 8

Remove the existing LAT CABLE using the following steps:

• Unscrew the threaded end of CABLE from the HEAD PLATE ASSEMBLY.

• Route the LAT CABLE around the PULLEY BLOCK as shown in FIGURE 8.

REMOVE CABLE

FIGURE 8

• The pulleys in TOP BOOM may need to be temporarily removed to remove CABLE.

• Route the LAT CABLE around the TOP BOOM as shown in FIGURE 8.

• Disconnect LAT BAR from TOP BOOM.

STEP 9

Install the NEW 110-3/4” CABLEASSY (16) using the following steps:

• Route the CABLE (16) back over one pulley in the TOP BOOM, down through the PULLEY BRACKET (2) and over the second

pulley in the TOP BOOM.

• Route the CABLE (16) around the PULLEY BLOCK as shown in FIGURE 9.

• Route the CABLE (16) through the TOP BOOM as shown in FIGURE 9. The pulleys in TOP BOOM may need to be temporarily

removed to perform this step. (Note: Make sure the CABLE is running OVER the BOLTS connecting the FRONT UPRIGHT

to the TOP BOOM. These may also have to be removed to perform this step.)

FIGURE 9

FIGURE 10

3/8 X 1-3/4” 13

STEP 10

• Loop CABLE (16) around one 3-1/2” PULLEY (5) in the PULLEY

BRACKET (2) using one 3/8 X 1-3/4” BOLT (13) and one 3/8”

LOCKNUT (11) as shown in FIGURE 10.

• Screw the threaded end of CABLE (16) into the HEAD PLATE

ASSEMBLY.

IMPORTANT: Cable must run over the top of

bolts.

FIGURE 11

STEP 11

• Attach the hook end of 82-1/2” CABLE (17) to the CABLE SWIVEL (3) with one QUICK DISCONNECT LINK (8).

IMPORTANT: Tighten the QUICK DISCONNECT LINK (8) securely.

0123456

1/2 1/2 1/2 1/2 1/2 1/2

• Route the 82-1/2” CABLE (17) under the WEIGHT STACK as shown in FIGURE 11.

IMPORTANT:

Tighten QUICK DISCONNECT LINK

SECURELY.

FIGURE 13

FIGURE 12

STEP 12

• Screw the threaded end of 82-1/2” CABLE (17) to the PULLEY

BRACKET (2) as shown in FIGURE 12.

STEP 13

• Attach one 3-1/2” PULLEY (5) to the FRONT LEG (1) and one 3-1/2” PULLEY (5) to the BASE CONNECTION (4) using two 3/

8 X 1-3/4” BOLTS (13) and two 3/8” LOCKNUTS (11). (Note: Make sure CABLE (17) is running under PULLEYS.)

3/8 X 1-3/4” 13

1 17

FIGURE 14

STEP 14

• The 100 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit

from the machine. To use, you must slightly push against the foot plates to take tension off the pin.

• To set the correct amount of tension in the cables, adjust the 100 LEG PRESS into the last adjustment hole (so the LEG PRESS is

spread apart) and remove the WEIGHT STACK PIN. Thread the 110-3/4” CABLE (16) into the HEAD PLATE ASSEMBLY until

the PULLEY BRACKET (2) is held against the TOPBOOM and the cable is slightly pulling up on the HEAD PLATE. Tighten the

jan but securely. Next, thread the 82-1/2” CABLE (17) into the PULLEY BRACKET (2) until cable is tight , then tighten the jam

nut securely.

0123456

1/2 1/2 1/2 1/2 1/2 1/2

SPRING PIN ADJUSTMENT

Thankyou forpurchasingthe Parabody441101LEGPRESSADAPTER KIT. Ifunsureofproperuseof

equipment,callyour local Parabody distributororcall the Parabodycustomerservicedepartment at (800)

328-9714.

Inhaltsverzeichnis

Andere ParaBody Fitnessgeräte Handbücher

ParaBody

ParaBody 888101 Bedienungsanleitung

ParaBody

ParaBody 835102 Bedienungsanleitung

ParaBody

ParaBody 375101 Bedienungsanleitung

ParaBody

ParaBody 843101 Bedienungsanleitung

ParaBody

ParaBody 886 Montageanleitung

ParaBody

ParaBody 855 Bedienungsanleitung

ParaBody

ParaBody 856 Bedienungsanleitung

ParaBody

ParaBody 874106 Bedienungsanleitung

ParaBody

ParaBody 854 Montageanleitung

ParaBody

ParaBody 837101 Bedienungsanleitung

ParaBody

ParaBody 216 50 LB Bedienungsanleitung

ParaBody

ParaBody 884101 Bedienungsanleitung

ParaBody

ParaBody 821 Bedienungsanleitung

ParaBody

ParaBody 824 Bedienungsanleitung

ParaBody

ParaBody 822 Bedienungsanleitung

ParaBody

ParaBody 866103 Bedienungsanleitung

ParaBody

ParaBody 832102 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 360101 375 Bedienungsanleitung

ParaBody

ParaBody 807 BODYSYSTEM Montageanleitung

ParaBody

ParaBody 824101 Montageanleitung

ParaBody

ParaBody 8661O2 Bedienungsanleitung

ParaBody

ParaBody 844 Bedienungsanleitung

ParaBody

ParaBody 493 Montageanleitung

ParaBody

ParaBody 826 Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung

SteelFlex

SteelFlex PLHP Kurzanleitung