Paradyne 7112 Bedienungsanleitung
1
7112-A2-GN10-40 February 2000
Model 7112 T1 SNMP DSU/CSU
Startup Instructions
Document Number 7112-A2-GN10-40
February 2000
Product Documentation on the World Wide Web
We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the
waste of surplus printing. It also helps us maintain competitive prices for our
products.
Complete documentation for this product is available at www.paradyne.com.
Select Library →Technical Manuals →Subrate Digital Access Devices.
Select the following document:
7112-A2-GB20
Model 7112 T1 DSU/CSU, with Internal Ethernet LAN Adapter, User’s Guide
To request a paper copy of a Paradyne document:
HWithin the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
HOutside the U.S.A., call 1-727-530-8623
Package Checklist
Verify that your package contains the following in addition to the startup
instructions:
-A Model 7112 T1 DSU/CSU
-Wall-mount ac adapter
-One RJ48C unkeyed modular cable for T1 network
-One 8-position unkeyed modular cable for Ethernet LAN access
2 7112-A2-GN10-40
February 2000
Cables You May Need to Order
If connecting . . . Order a . . .
A VT100-compatible terminal
to the Terminal port Standard straight-through EIA-232 cable with DB25
plug connectors on both ends.
A PC to the Terminal port Standard straight-through EIA-232 cable with a DB25
plug connector on one end and a DB9 socket
connector on the other end.
An External Modem to the
Terminal port Standard crossover EIA-232 cable with DB25 plug
connectors on both ends.
A DTE with a V.35 connector
to the DTE port Standard straight-through V.35 cable with an MS34
plug connector on one end and an MS34 socket
connector on the other end.
A DCE with a V.35 connector
to the DTE port Standard V.35 crossover cable with MS34 plug
connectors on both ends.
Contact your sales or service representative to order these cables. For cable
details, refer to Cables and Pin Assignments, Appendix E, in the User’s Guide.
Before Installation
Before installation, read the Important Safety Instructions on page 11.
Make sure you have:
-A dedicated, grounded ac outlet within 6 feet of the unit that is protected by a
circuit breaker.
-A clean, well-lit, and ventilated site that is free from environmental extremes.
-Sufficient clearance for cable connections.
-An operable network connection.
-A VT100-compatible ASCII terminal or PC.
-If desired, an operable Ethernet LAN connection for access to your Network
Management System (NMS).
-If desired, an external modem and serial crossover cable.
3
7112-A2-GN10-40 February 2000
Installing the DSU/CSU
00-15310-02
RJ48C
Jack
NETWORK
TERMINAL
POWER
D
T
E
DTE
10BaseT
Connection
Terminal
Connection
Power
Connection
Network
Connection
DTE
Connection
10BaseT
NMS
NOTE:
The 10BaseT and network connectors are not keyed. Follow the installation
procedures carefully to avoid connection errors.
"Procedure
To install the DSU/CSU:
1. Plug the 8-pin connector on the RJ48C network cable into the NETWORK
connector on the DSU/CSU.
2. Plug the other end of the RJ48C network cable into the RJ48C modular jack.
3. Plug one end of the 34-pin V.35 cable into the DTE port of the DSU/CSU.
4. Plug the other end of the V.35 cable into the DTE.
5. Insert one unkeyed 8-pin connector on the Ethernet cable into the 10BaseT
port.
6. Insert the other end of the cable into the Ethernet interface of the LAN where
your NMS resides.
7. Plug the 25-pin end of an EIA-232 cable into the TERMINAL port of the
DSU/CSU.
4 7112-A2-GN10-40
February 2000
8. Plug the other end of the EIA-232 cable into either a VT100-compatible
terminal or PC.
9. Plug the end of the ac adapter into the POWER jack on the DSU/CSU.
10. Plug the ac adapter in an ac outlet.
11. Press Enter on the keyboard to display the Main Menu.
Using an External Modem
"Procedure
To connect an external modem instead of an asynchronous terminal or PC:
1. Use a standard serial crossover cable as shown in Figure 1 on the next page.
2. Enable auto-answer on your modem, and configure it to use standard
RS-232 detection and control for LSD, DSR, and DTR. Use the following
command string:
AT &C1 &D2 &S1 S0=1
Table 1. AT Command String
Command Description
&C1 Configures your modem to raise LSD after establishing a connection.
&D2 Configures your modem to drop connection when the DSU drops DTR.
&S1 Configures your modem to raise DSR when it begins to establish a
connection.
S0=1 Configures your modem to automatically answer incoming calls.
5
7112-A2-GN10-40 February 2000
NOTE:
The Pin 17 to Pin 24 crossovers shown in Figure 1 are not required and have
no effect with the Model 7112.
Pin 1
Pin 14
Pin 13
Pin 25
Pin 1
Pin 14
Pin 13
Pin 25
P2
Plug
Chassis Ground
TXD
RXD
RTS
CTS
DSR
Signal Ground
CD (RLSD)
TXC
RXC
DTR
XTXC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Pin
98-15811
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
P1
Chassis Ground
TXD
RXD
RTS
CTS
DSR
Signal Ground
CD (RLSD)
TXC
RXC
DTR
XTXC
Pin P2
P1
Plug
Figure 1. Serial Crossover Cable for External Modem
6 7112-A2-GN10-40
February 2000
Hardware Verification
-Verify that the OK LED is on.
-Verify that the FAIL is off.
97-15687
NetworkSystem Port
FT1/T1
CTS (106)
OK
FAIL
TEST
SIG
OOF
ALARM
EER
TXD (103)
RXD (104)
RTS (105)
DTR (108)
7112 SNMP DSU/CSU
MONITOR
In Out
-Verify that the User Interface Idle screen is displayed on the ASCII terminal or
PC.
Press the Enter key. Verify that the Main Menu appears.
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
main Access Level: 1 PARADYNE
Device Name: Model: 7112
MAIN MENU
Status
Test
Configuration
Control
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Ctrl-a to access these functions Exit
NOTES:
Your VT100 terminal or emulation software must be set to communicate at a
rate of 9.6 kbps, using characters of 8 bits, one stop bit, and no parity.
Verifying the connection to a LAN, router, or external modem requires setup
and configuration; see Chapter 3, Configuring the DSU/CSU, in the User’s
Guide.
7
7112-A2-GN10-40 February 2000
Setting Up the ATI
The User’s Guide contains details regarding the ASCII Terminal Interface (ATI).
When setting up the ATI:
-Refer to Chapter 1, About the T1 DSU/CSU, to determine the management
configuration(s) to manage the DSU with one of the user interfaces.
-Set up the device name. Refer to Chapter 3, Configuring the DSU/CSU.
-Establish security and Login IDs. Refer to Chapter 4, Security.
-Decide on an IP addressing scheme. Refer to Chapter 5, IP Addressing.
-Determine if you want SNMP traps generated. Refer to Chapter 8, Messages
and Troubleshooting.
-Change configuration option settings. Refer to Appendix A, Configuration
Option Tables, and Appendix B, Worksheets.
-Provide management connectivity with MIBII and enterprise-specific MIBs.
Refer to Appendix C, MIB Descriptions, and Appendix D, Standards
Compliance for SNMP Traps.
Configuration Options and Defaults
Tables 2 through 8 list the DSU/CSU’s configuration options and the default
values that have been preconfigured at the factory.
Table 2. System Options
Configuration Option Settings (default in Bold)
Self Test Enable, Disable
Test Timeout Enable, Disable
Test Duration (min) 1–120 [10]
8 7112-A2-GN10-40
February 2000
Table 3. Network Interface Options
Configuration Option Settings (default in Bold)
Primary Clock Source Network, Internal, Port
Line Framing Format ESF, D4
Line Coding Format B8ZS, AMI
Bit Stuffing 62411, Part68, Disable
Line Build Out (LBO) 0.0, –7.5, –15, –22.5
FDL Management Link Enable, Disable
FDL IP Address 000.000.000.000 –255.255.255.255, clear
FDL Subnet Mask 000.000.000.000 – 255.255.255.255
Network Initiated Line Loopback (LLB) Enable, Disable
Network Initiated Payload Loopback
(PLB) Enable, Disable
ANSI Performance Report Messages Disable, Enable
Circuit Identifier < Blank >
Table 4. Cross Connect Assignments
Configuration Option Settings (default in Bold)
Assign By Block, ACAMI, Channel
Synchronous Data Port Assignments P(B)
The default is all DS0s assigned to the
data
p
ort
...
d
ata port. P(B)
Table 5. Data Port Options
Configuration Option Settings (default in Bold)
Port Base Rate Nx64, Nx56
Invert Transmit Clock Enable, Disable
Transmit Clock Source Internal, External
Invert Transmit and Received Data Enable, Disable
Send All Ones on Data Port Not Ready Disable, DTR, RTS, Both
Action on Network Yellow Alarm None, Halt
Network Init. Data Channel Loopback Disable, V.54, FT1, Both
Port (DTE) Initiated Loopbacks Disable, DTLB, DCLB, Both
9
7112-A2-GN10-40 February 2000
Table 6. Ethernet Port Options
Configuration Option Settings (default in Bold)
Port Use 802.3, Version 2, Disable
IP Address [000.000.000.000] –255.255.255.255
IP Subnet Mask [000.000.000.000] –255.255.255.255
Default Gateway Address [000.000.000.000] –255.255.255.255
Table 7. Terminal Port Options
Configuration Option Settings (default in Bold)
Data Rate (Kbps) 2.4, 4.8, 9.6, 14.4, 19.2, 28.8, 38.4
Character Length 7, 8
Parity None, Even, Odd
Stop Bits 1, 2
Monitor DTR Enable, Disable
Login Required Enable, Disable
Port Access Level Level 1, Level 2, Level 3
Inactivity Timeout Enable, Disable
Disconnect Time (minutes) range 1 –60, 5
Table 8. Telnet Session Options
Configuration Option Settings (default in Bold)
Telnet Session Enable, Disable
Login Required Enable, Disable
Session Access Level Level 1, Level 2, Level 3
Inactivity Timeout Enable, Disable
Disconnect Time (minutes) range 1 –60, 5
10 7112-A2-GN10-40
February 2000
Table 9. SNMP Options
Configuration Option Settings (default in Bold)
General SNMP Management
SNMP Management Enable, Disable
Community Name 1 ASCII Text, Public
Name 1 Access Read, Read/Write
Community Name 2 ASCII Text
Name 2 Access Read, Read/Write
SNMP NMS Security
NMS IP Validation Enable, Disable
Number of Managers 1, 2, 3, 4, 5, 6, 7, 8, 9, 10
NMS nIP Address 000.000.000.000 –255.255.255.255
Access Level Read, Read/Write
SNMP Traps
SNMP Traps Enable, Disable
Number of Trap Managers 1, 2, 3, 4, 5, 6
Trap Manager nIP Address 000.000.000.000 –255.255.255.255
Trap Manager nDestination None, Mgmt, FDL
General Traps Disable, Warm, AuthFail, Both
Enterprise Specific Traps Enable, Disable
Link Traps Disable, Up, Down, Both
Link Trap Interfaces Network, Port, Both
Andere Handbücher für 7112
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Paradyne Netzwerk-Hardware Handbücher
Paradyne
Paradyne GranDSLAM 4200 Bedienungsanleitung
Paradyne
Paradyne 3160-A3 Handbuch
Paradyne
Paradyne MCC Bedienungsanleitung
Paradyne
Paradyne Comsphere 3510 Bedienungsanleitung
Paradyne
Paradyne ACCULINK 316x Handbuch
Paradyne
Paradyne BitStorm 4800 Express Bedienungsanleitung
Paradyne
Paradyne GranDSLAM 4200 Bedienungsanleitung
Paradyne
Paradyne Hotwire 5620 RTU Bedienungsanleitung
Paradyne
Paradyne Hotwire 5620 Bedienungsanleitung
Paradyne
Paradyne 7112 Bedienungsanleitung
Paradyne
Paradyne DC Power Entry Module 8820-S1-906 Bedienungsanleitung
Paradyne
Paradyne COMSPHERE 3800PLUS Bedienungsanleitung
Paradyne
Paradyne COMSPHERE 6700 Series Bedienungsanleitung
Paradyne
Paradyne Hotwire 5446 Bedienungsanleitung
Paradyne
Paradyne Hotwire 5216 Bedienungsanleitung
Paradyne
Paradyne MIM-4E1 Bedienungsanleitung
Paradyne
Paradyne Hotwire 7996 Original Betriebsanleitung
Paradyne
Paradyne MIM-2E1 Bedienungsanleitung
Paradyne
Paradyne Hotwire 7996 Bedienungsanleitung
Paradyne
Paradyne Hotwire 8779 Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
