Pfeiffer Vacuum EVB 016 Series Bedienungsanleitung
Operating Instructions
BP 805 271 BE (0209) 1
Angle Valve
electromagnetically actuated
with automatic voltage
adaptation 85 … 248 VAC
EVB 016 … 040 MA/MX
2BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi
In all communications with Pfeiffer Vacuum, please specify the information given on
the product nameplate. For convenient reference copy that information into the
nameplate replica below.
Typ:
No:
F-No:
Pfeiffer Vacuum, D-35614 Asslar
Nominal voltage
This document applies to products with the following part numbers:
Aluminum housing
with FPM seals
Stainless steel housing
with FPM seals
Nominal diameter
PFA34505 PFA34535 DN 16 ISO–KF
PFA44505 PFA44535 DN 25 ISO–KF
PFA54505 PFA54535 DN 40 ISO–KF
The part number (No) can be taken from the product nameplate.
If not indicated otherwise in the legends, the illustrations in this document cor-
respond to the valve with the nominal diameter DN 25 ISO-KF. They apply to
valves with other nominal diameters by analogy.
We reserve the right to make technical changes without prior notice.
The electromagnetically actuated bellows sealed angle valves are used as shut-off
or venting devices in vacuum applications.
The angle valves are opened electromagnetically and closed by means of a
prestressed pressure spring. They close, or remain closed, on power loss.
The following trade marks and firms are the property of their respective owners:
Loctite®Loctite Corporation
Torx®Camcar/Textron, Inc.
All other trade marks or trade names are the property of their respective owners.
Product Identification
Validity
Intended Use
Functional Principle
Trade Marks
BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi 3
Contents
Product Identification 2
Validity 2
Intended Use 2
Functional Principle 2
Trade Marks 2
1 Description 4
1.1 Operating Modes 4
1.2 Indication of Positions and Faults 5
1.3 Position Indicator (in REMOTE mode only) 5
2 Safety 6
2.1 Symbols Used 6
2.2 General Safety Instructions 6
2.3 Liability and Warranty 6
3 Technical Data 8
4 Installation 10
4.1 Vacuum Connection 10
4.2 Electrical Connection 11
4.2.1 Removing the Cover 11
4.2.2 Setting the Operating Mode Selection Switch 12
4.2.3 Connecting the Feeder Line 13
4.2.4 Connecting the Control Cable (for REMOTE Mode Only) 14
4.2.5 Mounting the Cover 15
5 Operation 16
5.1 Signaling Behavior 16
5.2 Indication of Positions and Faults 16
6 Deinstallation 18
6.1 Electrical Connection 18
6.2 Vacuum Connection 19
7 Troubleshooting 20
8 Maintenance 21
9 Spare Parts 28
10 Returning the Product 30
11 Disposal 30
Declaration of Contamination 31
4BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi
1 Description
The angle valve has two operating modes:
· REMOTE mode
Drive via control voltage 15 … 30 VDC.
· LOCAL mode
Drive via supply voltage 85 … 248 VAC.
The operating mode is selected by setting a switch (®212).
In the REMOTE mode, the supply voltage of 85 … 248 VAC is constantly fed. The
angle valve is opened and closed via the control contact (0 VDC).
a
b
c
d
PE
N
L
15 ... 30 VDC
Valve closed
Valve open
Control contact
0 VDC
85 ... 248 VAC
Customer's connection
Protective resistor
for 30 ... 60 VDC
4.7kW
100 mA
The angle valve is opened and closed directly via the supply voltage.
a
b
c
d
PE
N
L
Customer's connection
85 ... 248 VAC
1.1 Operating Modes
REMOTE mode
LOCAL mode
BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi 5
Green LED lit
Red LED lit
Red LED flashing
= valve open
= valve closed
= fault, for instance
a temperature overload
The integrated position indicator allows for polling the valve positions. In the event
of a fault, the signal "valve closed" is constantly fed.
a
b
c
d
PE
N
L
Protective resistor
for 30 ... 60 VDC
Valve closed
Valve open
Control contact
Customer's connection
15 ... 30 VDC
0 VDC
85 ... 248 VAC
4.7kW
100 mA
1.2 Indication of Positions
and Faults
1.3 Position Indicator
(in REMOTE mode only)
6BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi
2 Safety
DANGER
Information on preventing any kind of physical injury.
WARNING
Information on preventing extensive equipment and environmental damage.
Caution
Information on correct handling or use. Disregard can lead to malfunctions or
minor equipment damage.
20 Dimensions in mm
®2See page ...
· Adhere to the applicable regulations and take the necessary precautions for the
process media used.
Consider possible reactions of the process media due to the heat generated by
the product (®29).
· Adhere to the applicable regulations and take the necessary precautions for all
work you are going to do and consider the safety instructions in this document.
· Before beginning to work, find out whether any vacuum components are con-
taminated. Adhere to the relevant regulations and take the necessary pre-
cautions when handling contaminated parts.
Communicate the safety instructions to all other users.
Pfeiffer Vacuum assumes no liability and the warranty becomes null and void if
end-users or third parties
· disregard the information in this document
· use the product in a non-conforming manner
· make any kind of changes (modifications, alterations etc.) to the product
· use the product with accessories and options not listed in the corresponding
product documentation.
The end-user assumes the responsibility in conjunction with the process media
used.
2.1 Symbols Used
2.2 General Safety
Instructions
2.3 Liability and Warranty
BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi 7
Notes
8BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi
3 Technical Data
Connection flange DN 16 ISO-KF DN 25 ISO-KF DN 40 ISO-KF
Actuation opening: electromagnetically
closing: by pressure spring
Supply voltage
Frequency
Power consumption
85 … 248 VAC
50 / 60 Hz
400 W (max. upon switching on)
Pickup-/Holding power 405 / 8.1 W 416 / 8.3 W 367 / 7.5 W
Control voltage
Power consumption
15 … 30 VDC 1)
3 … 5 mA
Position indicator
switching voltage 2)
switching current 3)
15 … 30 VDC
100 mA
Type of protection
Protection class
IP 54 according to DIN 40 050
II
Cable diameter
feeder line
control cable
5 … 7 mm
5 … 7 mm
Installation angle
Flow direction
any
any
Cycle life 4) 2 million
Switching frequency
at 40 °C 5)
at 50 °C 5)
30 / min
20 / min
Opening time
Closing time
Dead time 6)
100 ms
240 ms
50 ms
120 ms
240 ms
170 ms
230 ms
700 ms
500 ms
Pressure range
Bursting pressure
1×10-8mbar … 1.3 bar (absolute)
3 bar (overpressure)
Pressure difference Dp
in closing direction
in opening direction
Opens to a pressure
difference Dp
1.3 bar
1.3 bar
1.3 bar
Ambient temperature 0 … 50 °C
Tightness 1×10-9mbar l/s
1) 30 … 60 VDC with serial resistor (RV= 4.7 kW, installation ®214)
2) Corresponds to the control voltage
3) Must be protected with a quick-acting 100 mA fuse provided by the end-user
4) Cycles without expendable parts (seals) and under clean operating conditions
5) Ambient temperature
6)
Dead time
Control-
signal Valve position
open
close
t
off
on
Opening time Closing time
BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi 9
Connection flange DN 16 ISO-KF DN 25 ISO-KF DN 40 ISO-KF
Conductance 7) 4 l/s 16 l/s 40 l/s
Materials
housing
inside section
seals
shell
aluminum (3.2374) or
stainless steel (1.4301)
1.4301 and 1.4541
FPM
PAGV 30
Weight
aluminum housing
stainless steel housing
1.3 kg
1.5 kg
2.2 kg
2.9 kg
4 kg
5.4 kg
7) For air with molecular flow
DN
DN
DN A B C D E F G
DN 16 ISO–KF 160 58 40 96 84.5 59 7.5
DN 25 ISO–KF 194 76 50 111 96.5 75 10
DN 40 ISO–KF 230 98 65 138 119.5 96 13.5
Dimensions in mm
10 BP 805 271 BE (0209) EVB 016 … 040 MA/MX.oi
4 Installation
Skilled personnel
The vacuum connection may only be established by persons who have
suitable technical training and the necessary experience or who have
been instructed by the end-user of the product.
DANGER
Caution: overpressure in the vacuum system >1 bar
Injury caused by released parts and harm caused by escaping process
gases can result if clamps are opened while the vacuum system is
pressurized.
Do not open any clamps while the vacuum system is pressurized. Use
the type clamps which are suited to overpressure.
Caution
Caution: vacuum component
Dirt and damages impair the function of the vacuum component.
When handling vacuum components, take appropriate measures to
ensure cleanliness and prevent damages.
Caution
Caution: dirt sensitive area
Touching the product or parts thereof with one's bare hands increases
the desorption rate.
Always wear clean, lint-free gloves and use clean tools when working
in this area.
Keep the protective lids.
Remove the protective lids and install the valve to the vacuum system by means of
the small flange fittings.
Any installation angle and flow direction may be chosen.
Clamp
ISO-KF
connection
flange
Protective lid
Seal with
centering ring
4.1 Vacuum Connection
Procedure
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Pfeiffer Vacuum Steuereinheit Handbücher
Pfeiffer Vacuum
Pfeiffer Vacuum OmniControl Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum EVI 005 MI Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum EVB 016 PA Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum PM Z01 295 Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum UVH 040 CU Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum EVA 016S Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum TCP 350 Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum EVB Series Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum CENTERONE-TWO Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum UVH 016 VI Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum TPG 361 Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum TPG 300 Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum N Series Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum TPG 500 Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum EVB 16 P A Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum BVML Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum RVG 050 C Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum DualGauge TPG 262 Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum UDV 146 Bedienungsanleitung
Pfeiffer Vacuum
Pfeiffer Vacuum HPU 001 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
