Pilz PNOZ m ES CANopen Bedienungsanleitung

PNOZ m ES CANopen

Operating Manual-1002699-EN-06

}Configurable control systems PNOZmulti 2

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PNOZ m ES CANopen

1002699-EN-06 3

Section 1 Introduction 5

1.1 Validity of documentation 5

1.2 Using the documentation 5

1.3 Definition of symbols 5

Section 2 Overview 7

2.1 Scope of supply 7

2.2 Unit features 7

2.3 Front view 8

Section 3 Safety 9

3.1 Intended use 9

3.2 System requirements 9

3.3 Safety regulations 10

3.3.1 Use of qualified personnel 10

3.3.2 Warranty and liability 10

3.3.3 Disposal 10

3.3.4 For your safety 10

Section 4 Function description 11

4.1 Operation 11

4.2 Data access 11

4.3 Block diagram 12

Section 5 Installation 13

5.1 General installation guidelines 13

5.2 Dimensions in mm 13

5.3 Connect the base unit and expansion modules 14

Section 6 Commissioning 15

6.1 Wiring 15

6.1.1 General wiring guidelines 15

6.1.2 Connecting the supply voltage 15

6.1.3 CANopen interface 16

6.2 Setting the transmission rate 16

6.3 Setting the station address 17

6.4 Connection example 18

6.5 Download modified project to the PNOZmulti safety system 18

Section 7 Operation 19

7.1 Messages 19

7.1.1 Display elements for device diagnostics 19

Section 8 Technical details 20

Contents

Operating Manual PNOZ m ES CANopen

1002699-EN-06 4

Section 9 Order reference 22

9.1 Product 22

9.2 Accessories 22

Introduction

Operating Manual PNOZ m ES CANopen

1002699-EN-06 5

1 Introduction

1.1 Validity of documentation

This documentation is valid for the product PNOZ m ES CANopen. It is valid until new doc-

umentation is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

1.2 Using the documentation

This document is intended for instruction. Only install and commission the product if you

have read and understood this document. The document should be retained for future ref-

erence.

1.3 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

Introduction

Operating Manual PNOZ m ES CANopen

1002699-EN-06 6

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PNOZ m ES CANopen

1002699-EN-06 7

2 Overview

2.1 Scope of supply

}Expansion module PNOZ m ES CANopen

}Jumper

2.2 Unit features

Using the product PNOZ m ES CANopen:

Expansion module for connection to a base unit from the configurable control system

PNOZmulti 2 .

The product has the following features:

}Can be configured in the PNOZmulti Configurator

}Connection for CANopen

}Station addresses from 0 ... 99, selected via rotary switch

}Transmission rate selected via rotary switch (1 MBit/s, 10 kbit/s, 125 kBit/s, 20 kbit/s,

250 kBit/s, 50 kbit/s, 500 kBit/s, 800 kbit/s)

}Status indicators for communication with CANopen and for errors

}128 virtual inputs and outputs on the control system PNOZmulti 2 can be defined in the

PNOZmulti Configurator for communication with the fieldbus CANopen.

}Max. 1 PNOZ m ES CANopen can be connected to the base unit

}Plug-in connection terminals:

either spring-loaded terminal or screw terminal available as an accessory (see order

reference)

}For details of the PNOZmulti 2 base units that can be connected, please refer to the

document "PNOZmulti System Expansion".

Overview

Operating Manual PNOZ m ES CANopen

1002699-EN-06 8

2.3 Front view

[1]

[3]

[2]

[4]

Legend

[1] LED

- Power

- Run

- Error

[2] Rotary switch

- DR = Transmission rate

- X10 = Tens digit for the station address

- X1 = Units digit for the station address

[3] X1: CANopen interface (male 9-pin D-Sub connector)

[4] X4: 0 V, 24 V:

Supply connections

Functional earth

Safety

Operating Manual PNOZ m ES CANopen

1002699-EN-06 9

3 Safety

3.1 Intended use

The fieldbus module PNOZ m ES CANopen is an expansion module of the configurable

control system PNOZmulti 2. It is used for communication between the configurable control

system PNOZmulti 2 and CANopen.

CANopen is designed for fast data exchange at field level. The expansion module PNOZ m

ES CANopen is a passive CANopen subscriber (Slave). The basic communication func-

tions with CANopen conform to the guidelines of the CANopen User Group CiA DS-301

V4.2.0. The central controller (master) reads input information from the slaves and writes

output information to the slaves as part of each cycle. As well as the cyclical transfer of us-

able data, the expansion module PNOZ m ES CANopen also has diagnostic and commis-

sioning functions. Data traffic is monitored on the Master/Slave side.

The expansion module may only be connected to a base unit from the configurable system

PNOZmulti 2 (please refer to the document "PNOZmulti System Expansion" for details of

the base units that can be connected).

The configurable system PNOZmulti 2 is used for the safety-related interruption of safety

circuits and is designed for use in:

}Emergency stop equipment

}Safety circuits in accordance with VDE0113 Part 1 and EN60204-1

The expansion module may not be used for safety-related functions.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the product

}Use of the product outside the areas described in this manual

}Use of the product outside the technical details (see Technical details [ 20]).

NOTICE

EMC-compliant electrical installation

The product is designed for use in an industrial environment. The product

may cause interference if installed in other environments. If installed in other

environments, measures should be taken to comply with the applicable

standards and directives for the respective installation site with regard to in-

terference.

3.2 System requirements

Please refer to the "Product Modifications PNOZmulti" document in the "Version overview"

section for details of which versions of the base unit and PNOZmulti Configurator can be

used for this product.

Safety

Operating Manual PNOZ m ES CANopen

1002699-EN-06 10

3.3 Safety regulations

3.3.1 Use of qualified personnel

The products may only be assembled, installed, programmed, commissioned, operated,

maintained and decommissioned by competent persons.

A competent person is someone who, because of their training, experience and current pro-

fessional activity, has the specialist knowledge required to test, assess and operate the

work equipment, devices, systems, plant and machinery in accordance with the general

standards and guidelines for safety technology.

It is the company’s responsibility only to employ personnel who:

}Are familiar with the basic regulations concerning health and safety / accident preven-

tion

}Have read and understood the information provided in this description under "Safety"

}And have a good knowledge of the generic and specialist standards applicable to the

specific application.

3.3.2 Warranty and liability

All claims to warranty and liability will be rendered invalid if

}The product was used contrary to the purpose for which it is intended

}Damage can be attributed to not having followed the guidelines in the manual

}Operating personnel are not suitably qualified

}Any type of modification has been made (e.g. exchanging components on the PCB

boards, soldering work etc.).

3.3.3 Disposal

}When decommissioning, please comply with local regulations regarding the disposal of

electronic devices (e.g. Electrical and Electronic Equipment Act).

3.3.4 For your safety

The unit meets all the necessary conditions for safe operation. However, you should always

ensure that the following safety requirements are met:

}This operating manual only describes the basic functions of the unit. The expanded

functions are described in the PNOZmulti Configurator's online help. Only use these

functions once you have read and understood the documentations.

}Do not open the housing or make any unauthorised modifications.

}Please make sure you shut down the supply voltage when performing maintenance

work (e.g. exchanging contactors).

Inhaltsverzeichnis

Andere Pilz Steuereinheit Handbücher

Pilz

Pilz PMCtendo SZ Bedienungsanleitung

Pilz

Pilz PNOZ m0p Bedienungsanleitung

Pilz

Pilz PIT si1.1 Bedienungsanleitung

Pilz

Pilz PIT es Set/1 Bedienungsanleitung

Pilz

Pilz PNOZ m EF 4DI4DOR Bedienungsanleitung

Pilz

Pilz PIT js2 Bedienungsanleitung

Pilz

Pilz PSSu E F 4DI-T Bedienungsanleitung

Pilz

Pilz PSSu E S 2AI RTD Bedienungsanleitung

Pilz

Pilz PNOZ mc10p Bedienungsanleitung

Pilz

Pilz PNOZ ms1p Bedienungsanleitung

Pilz

Pilz PNOZ mc12p Bedienungsanleitung

Pilz

Pilz PITmode flex visu Bedienungsanleitung

Pilz

Pilz PSSu K F EI CV Bedienungsanleitung

Pilz

Pilz PNOZ po3.1p Bedienungsanleitung

Pilz

Pilz PSEN ma1.4-51 M12/8-0.15m Bedienungsanleitung

Pilz

Pilz PNOZ m EF 8DI4DO Bedienungsanleitung

Pilz

Pilz PZE 9P Bedienungsanleitung

Pilz

Pilz PZE X4VP4 Bedienungsanleitung

Pilz

Pilz mc1p coated Bedienungsanleitung

Pilz

Pilz PSSu E AI SHT2 Bedienungsanleitung

Pilz

Pilz PSSu E F 4DO 0.5 Bedienungsanleitung

Pilz

Pilz PNOZ ms4p Bedienungsanleitung

Pilz

Pilz PNOZ m EF 2MM Bedienungsanleitung

Pilz

Pilz PNOZ mc7p Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung