POSIFLEX TX-4200 Bedienungsanleitung

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions manual, may cause interference to radio communications.

It has been tested and found to comply with limits for a Class A digital device pursuant to subpart

B of Part 15 of FCC Rules, which are designed to provide reasonable protection against

interference when operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference in which case the user at his owns expense will be

required to take whatever measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized technicians opens

the machine. The user should consult his/her dealer for the problem happened. Warranty voids if

the user does not follow the instructions in application of this merchandise. The manufacturer is by

no means responsible for any damage or hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex

Technology, Inc. will assume no liability for any technical inaccuracies or editorial or other errors

or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise

damages, including without limitation loss of data or profits, resulting from the furnishing,

performance, or use of this material.

This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims any

warranties, expressed, implied or statutory, including without limitation implied warranties of

merchantability or fitness for particular purpose, good title and against infringement.

The information in this manual contains only essential hardware concerns for general user and is

subject to change without notice. Posiflex Technology, Inc. reserves the right to alter product

designs, layouts or drivers without notification. The system integrator shall provide applicative

notices and arrangement for special options utilizing this product. The user may find the most up

to date information of the hardware from: http://www.posiflex.com or http://www.posiflex.com.tw

or http://www.posiflexusa.com

All data should be backed-up prior to the installation of any drive unit or storage peripheral.

Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this

or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a

retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,

or otherwise, without prior express written consent from Posiflex Technology, Inc. the publisher of

this documentation.

©Copyright Posiflex Technology, Inc. 2013

All brand and product names and trademarks are the property of their respective holders.

TX-4200/4200E

Fan Free Terminal

User’s Manual

Rev.: Original

14520900010

Page 2

ALERT TO OUR HONORABLE CUSTOMERS:

Please always read thoroughly all the instructions and documents delivered

with the product before you do anything about it. Don’t take any premature

action before you have a full understanding of the consequences.

DAILY MAINTENANCE GUIDE

For regular cleaning of the TX systems, please use only soft haired brush or

dry soft cloth. You may use moist soft cloth to remove stains when necessary.

Apply only suitable amount of mild neutral cleaner for obstinate stains. Please

note that never use Acryl dissolving solvent or Polycarbonate dissolving

solvent. You may apply ammonia-based glass cleaner only on the screen

surface.

ABOUT THIS PRODUCT

TX-4200/4200E Series is a multi-purpose controller that can be ideal for

various applications. With a compact housing, Intel Cedar view dual core

processor, standard VGA + HDMI display interface, mini-PCIe expansion slot

for WIFI, PS/2 port, VESA mounting and more, TX-4200/4200E Series is so

versatile that it can be used as a full fledge POS Box, a Kitchen Video System

(KVS) controller and a Digital Signage controller.

The most reliable Fanfree structure for harsh environment.

Supports Win POSReady, Win7, Win XP pro and Linux environment.

Supports SSD (Solid-State Drive) Data Storage Device or HDD.

POS system for power saving (Suspension Mode).

External power support for COM and VGA ports.

CR port control maximum 2 cash drawers.

Mini-PCI-E without USB port for TX-4200E.

Desktop or Wall Mount Installation.

TX-3000 VGA daughter card for 2

VGA display.

Option Power USB board to support 24V power USB for TX-4200E

only

INTRODUCTION

PRODUCT PICTURES

4200E

Front View

4200

Front View

Page 3

PARTS IDENTIFICATION

1. Power switch.

2. LED indicator for power and SSD indicator.

3. Power USB 24V port (TX-4200E)/USB port (TX-4200)

4. I/O plate (TX-4200/4200E) on the rear side.

PRODUCT FEATURES

Standard Features:

TX-4200E TX-4200

ITEM SPECIFICATION

SPECIFICATION

Remarks

CPU Intel Cedar View

D2550 1.86G, 1M

Cache, Dual Core

Intel Cedar View

D2550 1.86G, 1M

Cache, Dual Core

Chipset Intel NM10 Intel NM10

VGA port D-SUB 15Pin -1 D-SUB 15Pin -1 support +12V

LCD display

N/A N/A

DRAM

memory

DDR3 1066, SO-

DIMM x 1 , Max

4GB

DDR3 1066, SO-

DIMM x 1 , Max

4GB

HDMI port

x1, on the I/O Plate

Parallel port

x1 x1 Need extension cable

(option)

PS/2 KB Yes, on the front

side

Yes, on the front

side

4200

Rear View

4200

Rear View

Page 4

Serial port DB9 X 2, RJ-

45 X 2

on the I/O plate,

COM5 & COM6

throught special

convert cable.

DB9 X 2, RJ-

45 X 2

on the I/O plate

COM 1/2/3/4 reservd

+ 5V power enable by

software

setting,COM5/COM6

5V BY Jumper

Setting,

COM1/2/3/4/5/6

reservd +12V by

jumper setting

Extension

slot

Mini-PCI-E without

USB port

N/A reserved for external

WiFi antenna

CR port Yes, one port

control 2 CRs on

the I/O Plate

Yes, one port

control 2 CRs on

the I/O Plate

Standard

USB port

6 ports, 5 ports on

the I/O plate,

optional one 24V

power USB Port on

the front side

6 ports, 5 ports on

the I/O plate, 1 port

on the front plate

Power USB card TX-

4200_24V must be

installed for power

USB FUNCTION

(option)

Audio port Line out & 2W

internal Speaker

Line out

ETHER

NET

port

10/100/1000 Mb x 1

Storage

device

2.5" SATA HDD or

SSD

2.5" SATA HDD or

SSD

Power

switch

Soft witch Soft switch On front panel

Mechanical

installation

Desk top or VESA

Wall mount

Desk top or VESA

Wall mount

VESA mount 100 x

100

Power

saving

Suspension mode Suspension mode

Power

supply

12V DC power

adaptor, 80W

12V DC power

adaptor, 60W

TX-4200E use 150W

if power USB used.

TX-4200 use 80W if

VGA port used.

Page 5

Indicator

LED

Power ON/ standby,

bi-color LED,

Ethernet Link LED

on Ethernet

connector, HDD

lamp on front panel

Power ON/ standby,

bi-color LED,

Ethernet Link LED

on Ethernet

connector, HDD

lamp on front panel

On front panel

Fanless

system

Yes Yes

OS support

XP Pro, POSReady

7, Win 7

Linux , XP Pro,

POSReady 7, Win 7

SSD SSD (16GB

Minium)

SSD (16GB

Minium)

throught SATA

interface

2nd display

port

D-SUB 15 Pin; TX-

3000 VGA daughter

card for 2

display

D-SUB 15 Pin; TX-

3000 VGA daughter

card for 2

display

Port on the I/O plate

TX-4200 power

adaptor need upgrade

to 80W

COM 3/4

convert

cable

RJ45 to DB9

convert cable

RJ45 to DB9

convert cable

COM 5/6

extension

cable

Yes N/A

Power USB

port

24V/2Ax1 N/A Power adaptor need

upgrade to 150W

WiFi 802.11n N/A throught MiNi PCI-E

Interface

Wall mount

bracket

Yes Yes

Table: Summary of features

Optional Items:

Note: The underlined items in the following list means that option must be

set prior to shipment from the factory. The rest of items can be set by

the dealers.

a) DDR3 SODIMM memory expansion up to 4GB max.

b) SATA SSD kit (SSD can’t coexist with SATA HDD in main unit).

c) Preload OS Windows XP Pro, Win 7, POS Ready or Linux.

Page 6

d) Wireless LAN adaptor in Mini-PCI-E interface.

e) RJ-45 to DB9 connector cable.

INSTALLATION GUIDES

Hardware Power Switch

The power switch located in the front bezel of main unit. It is a pushbutton

switch and controls the power on/off of the whole system.

This power switch turns the system on when pushed

only. This switch turns the system off when pushed

again during power on status. However, if the system

hangs due to any reason such as software resource

conflict, a simple push on the switch in 10 sec may turn

off the power.

Note: There must always be at least 10 seconds waiting before switching

on again once the system is powered off successfully.

Indicators of power, status and HDD

There are two indicator LED modules serving for several purposes at front

bezel. For HDD indicator, it will flash orange light when the

HDD is operating. The relationship between the indicator

status and other conditions of “Power LED” is summarized in

the following table:

CAUTION: Before any installation or cable connection to the set, please

always make sure that the system is turned off and the external power

source to the set is removed to prevent electric hazard! Never touch any

metal pin in the connectors or circuits to avoid high voltage hazard or

Indicator Terminal Status

LED colour

Standby Orange

Power Status Power On Blue

Page 7

electrostatic discharge damage unless the operator is well grounded. Failure

to do the above will void the product warranty!

Display Issues

VGA Port

The VGA port in the TX series system supports either a separately connected

LCD monitor or touch monitor. To support the DC power to the display

monitor, it requires a qualified technician to set up through BIOS setting. To

supply the necessary power through the VGA connector, please refer to the

Posiflex technical information. Do not connect other monitor to this port

before the power in this port is disabled.

Rear I/O Plate

Please hold the base and pull up the terminal carefully then you will see the

I/O plate.

TX-4200E Rear View

Page 8

A: 1 x Audio line out port (optional)

B: 1x Antenna port (optional)

C: 1x CR port

D: 1x 2

VGA port (optional)

E: 2x Serial port (RJ-45) COM3 & COM4 port

F: 2x Serial port (RS-232) COM1 & COM2 port

G: 5x USB ports

H: 1x LAN port

I: 1x HDMI port

J: 1x LPT port

K: 1x VGA port (D-sub, 15 PIN)

L: 1x DC IN power connecter

Front I/O Plate

Please hold the base toward yourself for front I/O plate view.

TX-4200E TX-4200

TX-4200 Rear View

I J K

Page 9

M: 1x Power USB 24V

N: 1x USB

O: 1x PS/2

In TX series system, COM1, 2, 3 and 4 can supply a +5 V DC through system

BIOS, COM 5 &6 +5V/+12V are supported by jumper setting. The VGA port

can support +12 V power through system BIOS setting for Posiflex LCD

display monitor. 2

VGA port +12V power is set by jumper. Nevertheless,

except Posiflex peripheral device, do not connect any other device to this

port before the power in this port is disabled.

CAUTION: Please turn off the system power first! Then hold the base and

move the terminal carefully.

Connecting Cables

To have the terminal ready for operation, please connect all required cables to

the appropriate connectors. Please make sure that each connector is connected

to the correct port with the correct orientation. Damages due to incorrect

connection or orientation are not covered by product warranty!

Some connectors like the COM port or LAN port or CR connector have

to be gently inserted until a click is heard. It is recommended that connectors

such as the COM port and VGA connector be screwed into place once

seated. Please make sure that each connector has to be connected to the right

device in the right way.

CAUTION: On doing any insertion or extraction of any connector, please

always hold the connector head itself instead of pulling on the

cable wire. Failure to do this could damage the cable and jack

that is considered as an artificial destruction and is not

covered by the warranty.

Connecting Cash Drawer (Optional)

The RJ45 connector in I/O area of a TX-4200/4200E system can be used for

controlling most of the common cash drawers which are driven by +12V signal.

However, it is most recommended to use Posiflex CR-2000 or CR-2200 or

CR-3100 or CR-3200 or CR-4000 or CR-4100 or CR-4210 or CR-6310 for

Page 10

best compliance to operate the opening mechanism and to monitor the drawer

open status.

Use the cable supplied with the cash drawer for connection to the CR port in

TX system. This cable has a 6-pole plug at one end and an 8-pole plug at the

other. The 8-pole plug should be inserted into the connector marked: “signal

cable from POS Printer” at the rear of the cash drawer. The 6-pole plug should

be inserted in the connector marked “CR” found in the main connection area in

the system.

Wall Mount Application

In order to present in clearly organized visuals and freeing up valuable desk

space, TX-4200/4200E series support wall mount application and VESA

mount standard. After screw-fitting the upgrade kit WB*4200 bracket, TX-

4200/4200E can apply mounting function and VESA standard application. For

installation step, please refer to the WB*4200 bracket installation guide.

System Recovery

For TX systems preloaded with Windows POS Ready / Win 7 / Linux on HDD

or Solid State Drive, Posiflex provides recovery

DVD delivered with the terminal for the preloaded operating system. The

System Integrator shall take care of software restoration after OS

recovered. A Posiflex supplied USB interface DVD drive will be required for

such action. Other brand DVD-ROM drive may require its own driver

different from what supported in the recovery DVD.

Please use the recovery DVD in rescue operation only. Using it otherwise

may wipe out whatever stored in the storage device! All upgrade devices

drivers needed for manual installation in usual way are available in the

subfolder “\drivers” in OS recovered HDD and the latest versions of these

required drivers will be available on our web: http://www.posiflex.com. Then

follow instructions from your system integrator for software recovery.

Operating System Installation

This product is highly professionalized equipment. The installation of an OS

into a machine without any preloaded OS could be a major difficulty for

average user or obstacle by possibly unintentional negligence even for PC

veterans to accomplish such a task. Therefore, OS installation into a system

Andere Handbücher für TX-4200

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere POSIFLEX Touch-Terminal Handbücher

POSIFLEX

POSIFLEX TX-5300 Bedienungsanleitung

POSIFLEX

POSIFLEX XP-2000 Series Bedienungsanleitung

POSIFLEX

POSIFLEX KS - 6715 Bedienungsanleitung

POSIFLEX

POSIFLEX LM-31XXE Bedienungsanleitung

POSIFLEX

POSIFLEX KS - 6915 Bedienungsanleitung

POSIFLEX

POSIFLEX Cash Drawer CR400X Bedienungsanleitung

POSIFLEX

POSIFLEX HT-2000 Series Bedienungsanleitung

POSIFLEX

POSIFLEX JIVA TP-5700 Bedienungsanleitung

POSIFLEX

POSIFLEX RT-2015E Bedienungsanleitung

POSIFLEX

POSIFLEX XT-4015-G2 Bedienungsanleitung

POSIFLEX

POSIFLEX KS-7415 Bedienungsanleitung

POSIFLEX

POSIFLEX PB-7700 Series Bedienungsanleitung

POSIFLEX

POSIFLEX TX-4200 Bedienungsanleitung

POSIFLEX

POSIFLEX SA-104 Bedienungsanleitung

POSIFLEX

POSIFLEX PS Series Bedienungsanleitung

POSIFLEX

POSIFLEX HT-3200 SERIES Bedienungsanleitung

POSIFLEX

POSIFLEX XT- 3015 Bedienungsanleitung

POSIFLEX

POSIFLEX Jiva KS-6215 Series Bedienungsanleitung

POSIFLEX

POSIFLEX RT-1016A Bedienungsanleitung

POSIFLEX

POSIFLEX TX-2000 Bedienungsanleitung

POSIFLEX

POSIFLEX PS-3216A Bedienungsanleitung

POSIFLEX

POSIFLEX PS-3515 Bedienungsanleitung

POSIFLEX

POSIFLEX KS - 7212/X Bedienungsanleitung

POSIFLEX

POSIFLEX XT-3817 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung